Luxor MGB3040 30" x 40" Mobile Glass Marker Board (Discontinued)
190.00
NewCondition
OutOfStock
We're sorry, but we no longer offer this item.
Call us at 1-800-944-4573 for personalized recommendations
or check out these similar items that may be a good fit:
Luxor MGB3040 30" x 40" Mobile Glass Marker Board (Discontinued)
SWIPE FOR MORE IMAGES
- 0
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
Product Description
This Luxor MGB3040 30" x 40" Mobile Glass Marker Board has tempered 5/16" thick glass with silver-painted steel frame. Its glass will not stain or ghost and it is an ideal surface for wet/dry erase markers. This glass board features a lock and pivot system that allows glass to tilt up to 8° in each direction for comfortable writing and clearer viewing. Plus, it comes with four non-marring grip swivel casters with locking brakes for easy maneuverability and stability. This Luxor MGB3040 30" x 40" Mobile Glass Marker Board comes with a lifetime warranty.
Product Details
- Board Size: 30"W x 40"H
- Assembled Size: 35"W x 68"H x 24"D
- Made of tempered 5/16" (8mm) thick glass
- Will not stain or ghost
- Silver finish on Steel frame
- Glass is the ideal surface for wet/dry erase markers
- Comes with 4 locking non-marring grip swivel casters
- Warranty: Lifetime Warranty
Demonstration Video
Assembly Guide - Luxor MGB3040 Mobile Glass Board
Transcript:
Materials included with the MGB3040 Mobile Glass Board. Carefully remove the protective packaging making sure to inspect the glass for cracks before assembly. If cracks are found, DO NOT ASSEMBLE. Contact customer service immediately. Place the padded packaging onto a table to raise the glass up during assembly. Step 1: With assistance life the glass board onto the packing on a large table. Left hole is towards the first top of the units. Step 2: Parts Needed. Step 2a: Raise Frame (D x 2) so that it is upright and insert Plastic Washers (F) into Screw (G). Insert Knob (E) into the ...
Read More
Materials included with the MGB3040 Mobile Glass Board. Carefully remove the protective packaging making sure to inspect the glass for cracks before assembly. If cracks are found, DO NOT ASSEMBLE. Contact customer service immediately. Place the padded packaging onto a table to raise the glass up during assembly. Step 1: With assistance life the glass board onto the packing on a large table. Left hole is towards the first top of the units. Step 2: Parts Needed. Step 2a: Raise Frame (D x 2) so that it is upright and insert Plastic Washers (F) into Screw (G). Insert Knob (E) into the oval shaped hole at the top of (D). Attach Plastic Washer (F) to the other side of screws (G) & Knob (E). Screw knob (E) into the side “top” most hole on the glass board clamp, then screw (E) into the middle hole on the glass board clamp. Using Allen wrench (L). Repeat Step 2a. Do the same to the other side of the glass board clamp. Step 3: Parts Needed. Step 3: With assistance, attach cross bar (H) to both legs with screws (Gx4) with allen wrench (L). Part 5: Parts Needed. Part 5: With a wrench attach casters (A) to bottom frame (B). Part 5: Parts Needed. Step 5a: With assistance attach metal washers (J) into screw (K) and attach bottom caster bar (B) to the bottom of the frame (D). Tighten with Allen Wrench (M). Repeat Step 5a for other side. Part 6: Parts Needed. Step 6: With assistance, attach the bottom cross bar (H) with screws (Gx4) and allen wrench (L) into Bottom cross bars (B). Step 7: With assistance carefully lift the mobile glassboard upright. Loosen the knobs to tilt the Glassboard forward or backwards and tighten to set your position in place. Remove safety clips. Assembly Complete!
