MHL Matt UV 3mil 51" x 500' Low Temp Thermal Laminating Film
530.79
NewCondition
InStock
MHL Matt UV 3mil 51" x 500' Low Temp Thermal Laminating Film
SWIPE FOR MORE IMAGES
- 0
- 1
Product Description
MHL Matt 3mil 51" x 500' low temperature laminating film eliminates reflection and glare while hiding minor imperfections in the output. MHL Matt 3.0 mil provides moderate UV protection for indoor and short term outdoor graphics. Typical applications for MHL Matt are xerographic, offset, or inkjet bond output for viewing where there is little control over lighting conditions. This makes MHL Matt ideal for the creation of POP displays, ceiling graphics, trade show signs, etc. Get 51" x 500' of 3mil MHL Matt UV Low Temp film with every order. Product number MM51503.
Product Details
- Film Width: 51"
- Film Length: 500'
- Film Thickness: 3.0mil
- Core Size: 3"
- Finish: Matte
- Base Film: 0.5mil (13 micron) polyester
- Adhesive: 2.5 mil (62 micron) co-extruded polyethylene copolymer
- Initial Tack: None
- Application Speed: 1' - 10' per minute
- Application Temperature: 190 F - 220 F
- Release Liner: None
Item Specifications
- Specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators
- Co-extruded for a carefully balanced ratio of polyester film to adhesive.
- Higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out).
- Available in a variety of thicknesses and finishes from standard gloss and lustre finishes to scratch-resistant films suitable for outdoor applications
- Suitable for both single sided and double sided laminating (encapsulation) of photographic, electrostatic, inkjet-bond, xerographic and lithographic output, as well as many more applications.
- Incorporate UV absorbers for excellent protection from damaging UV rays.
Recommended for you
-
MHL Gloss 5mil Low Temp Thermal Laminating Film
Starting At: $221.89
-
Laminating Workstation
$321.49
-
Sooper Media Roll Clips
Starting At: $30.20
-
Core ID Cards for Vinyl Rolls
Starting At: $11.69
Tips and Technical Data
Tips For Applying MHL UV Thermal Films:
- Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down.
- Co-extruded for a carefully balanced ratio of polyester film to adhesive.
- Use your idler bar to increase the area of contact between the heated rollers and the film.
- To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results.
- MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
Technical Data
MHL Low Temperature Matte is a 3 mil (75µ) high clarity, abrasion-resistant PET thermal laminating film with a low melt-point adhesive designed for high-speed single- and double-sided lamination. It off ers excellent glare reduction. The film is resistant to water, oil, acid, and alkali and can be die cut.
Typical Applications
- Ideal for tradeshow graphics.
- Suitable for a wide variety of POP displays.
Physical Characteristics
Film Thickness | 3 mil (75µ) |
---|---|
Film/Adhesive Ratio | 0.5:2.5 |
Processing Temperature | 185°F to 195°F (85°C to 91°C) |
Shelf Life | Use within 1 year after opening original box |
Storage Conditions | 59°F to 72°F (15°C to 22°C); 50 - 55% Relative Humidity |