Product listing: Lawson Pacemaker 110" III IV High Speed Steel Replacement Blade (JH-40500HSS) to Ledco EP-25 Pre-Mask 25" Tape Applicator 110V (2025100)
-
Lawson Pacemaker 110" III IV High Speed Steel Replacement Blade (JH-40500HSS)
- Type of Blade: High Speed Steel
- Dimensions (L x W x T): 125.000" x 5.000" x .495"
- Holes/Slots: 63H
- Hole Size: 1/2"-13
- Type of Blade: High Speed Steel
Part #: JH-40500HSS -
Lawson Pacemaker 69" III IV High Speed Steel Replacement Blade (JH-40200HSS)
- Type of Blade: High Speed Steel
- Dimensions (L x W x T): 83.000" x 5.000" x .496"
- Holes/Slots: 42H
- Hole Size: 1/2"-13
- Type of Blade: High Speed Steel
Part #: JH-40200HSS -
Lawson Pacemaker III or IV 47" Tungsten Carbide Replacement Blade (JH-39020TCT)
- Material: Tungsten carbide tipped
- Compatible Models: Pacemaker III or VI 47"
- Holes: 30 Holes
- Hole Size: 1/2" - 13
- Length: 59"
Part #: JH-39020TCT -
Lawson PM II 59" 2BE4040 4" 2" End to Center HSS Replacement Blade (JH-39820HSS)
- Type of Blade: High Speed Steel
- Dimensions (L x W x T): 72.000" x 5.000" x .496"
- Holes/Slots: 36H
- Hole Size: 1/2"-13
- Type of Blade: High Speed Steel
Part #: JH-39820HSS -
Lawson Wohlenberg 115F Metric HSS Replacement Blade (JH-38820MHSS)
- Compatible Models: Lawson, Wohlenberg 115 F METRIC
- Material: High Speed Steel
- Holes: 14 (M12 x 1.75)
- Length: 54.33"
- With: 4.921"
Part #: JH-38820MHSS -
Lawson Wohlenberg 115F Metric Replacement Blade (JH-38820M)
- Compatible Models: Lawson, Wohlenberg 115 F METRIC
- Material: Standard Inlay
- Holes: 14 (M12 x 1.75)
- Length: 54.33"
- With: 4.921"
Part #: JH-38820M -
Lawson Wohlenberg 115F Standard HSS Replacement Blade (JH-38820HSS)
- Compatible Models: Lawson, Wohlenberg 115 F STANDARD
- Material: High Speed Steel
- Holes: 14 (1/2 x 13)
- Length: 54.33"
- With: 4.921"
Part #: JH-38820HSS -
Lawson Wohlenberg 115F Standard Replacement Blade (JH-38820)
- Compatible Models: Lawson, Wohlenberg 115 F STANDARD
- Material: Standard Inlay
- Holes: 14 (1/2 x 13)
- Length: 54.33"
- With: 4.921"
Part #: JH-38820 -
Lawson Wohlenberg 38F 44 FS100 Front Replacement Blade (JH-38100)
- Compatible Models: Lawson, Wohlenberg 38 F, 44 FS100
- Material: Standard Inlay
- Holes: 12
- Length: 19.685"
- With: 4.527"
Part #: JH-38100 -
Lawson Wohlenberg 38F 44 FS100 HSS Front Replacement Blade (JH-38100HSS)
- Compatible Models: Lawson, Wohlenberg 38 F, 44 FS100
- Material: High Speed Steel
- Holes: 12
- Length: 19.685"
- With: 4.527"
Part #: JH-38100HSS -
Lawson Wohlenberg 38F 44 FS50 A43 RT 343 Side Blade (JH-38400)
- Compatible Models: Lawson, Wohlenberg 38F, 44 FS50, A 43
- Material: Standard Inlay
- Holes: 10
- Length: 16.688"
- With: 4.5"
Part #: JH-38400 -
Lawson Wohlenberg 38F 44 FS50 A43 RT 343 Side HSS Blade (JH-38400HSS)
- Compatible Models: Lawson, Wohlenberg 38F, 44 FS50, A 43
- Material: High Speed Steel
- Holes: 10
- Length: 16.688"
- With: 4.5"
Part #: JH-38400HSS -
Lawson Wohlenberg 44 FS100 HSS Side Replacement Blade (JH-38200HSS)
- Compatible Models: Lawson, Wohlenberg 44 FS100
- Material: High Speed Steel
- Holes: 10
- Length: 15.345"
- With: 4.527"
Part #: JH-38200HSS -
Lawson Wohlenberg 44 FS50 A43 RT 343 Front Blade (JH-38500)
- Compatible Models: Lawson, Wohlenberg 44 FS50, A 43
- Material: Standard Inlay
- Holes: 12
- Length: 22"
- With: 4.5"
Part #: JH-38500 -
Lawson Wohlenberg 44 FS50 A43 RT 343 HSS Front Blade (JH-38500HSS)
- Compatible Models: Lawson, Wohlenberg 44 FS50, A 43
- Material: High Speed Steel
- Holes: 12
- Length: 22"
- With: 4.5"
Part #: JH-38500HSS -
Lawson Wohlenberg 88T A86 A90 Metric Replacement Blade (JH-38560M)
- Compatible Models: Lawson, Wohlenberg 88 T, A 86, A 90 METRIC
- Material: Standard Inlay
- Holes: 10 (M12 x 1.75)
- Length: 42.126"
- With: 4.921"
Part #: JH-38560M -
Lawson Wohlenberg 90F 92F Metric Replacement Blade (JH-38570M)
- Compatible Models: Lawson, Wohlenberg 90 F, 92 F METRIC
- Material: Standard Inlay
- Holes: 11 (M12 x 1.75)
- Length: 43.31"
- With: 4.92"
Part #: JH-38570M -
Lawson Wohlenberg 90F 92F Standard Replacement Blade (JH-38570)
- Compatible Models: Lawson, Wohlenberg 90 F, 92 F STANDARD
- Material: Standard Inlay
- Holes: 11 (1/2 x 13)
- Length: 43.31"
- With: 4.92"
Part #: JH-38570 -
Lawson Wohlenberg A112 A115 Metric Regent Replacement Blade (JH-38700M)
- Compatible Models: Lawson, Wohlenberg A 112, A 115 METRIC, Regent
- Material: Standard Inlay
- Holes: 13 (M12 x 1.75)
- Length: 52.756"
- With: 4.921"
Part #: JH-38700M -
Lawson Wohlenberg RW 6256 Replacement Blade (JH-38550HSS)
- Compatible Models: Lawson, Wohlenberg RW 6256
- Material: High Speed Steel
- Holes: 10
- Length: 41.732"
- With: 4.921"
Part #: JH-38550HSS -
Ledco 30" Automatic Laminate Cutter 110V (C300110-B)
- Variable speed up to 150 feet per minute.
- Adjustable speed even during operation.
- Feed table support for precise guidance of web.
- Two-sided cutting blades for twice the lifespan.
- Self-sharpening shear cutting blades.
Part #: C300110-B -
Ledco B64 64" Wide Format Hot Roll Laminator and Mounter (B640220A)
- Common Applications Include:
- Transfer tape applications.
- Vinyl application to sign blanks.
- Mounting and over-laminating using thermal mounting pouches.
- One sided over lamination using pressure sensitive films.
Part #: B640220A -
Ledco Digital 42" Laminator & Mounter (42B-0008)
- A Quality silicone rubber laminating rollers release materials easily and maintain their flexibility for a good edge seal.
- Two sets of rollers keep the film flat and tight while heat laminating so that the automatic fans cool and set the adhesive. When thermal films cool in a slack state, the surface of the lamination is wavy and rippled.
- Supply roll tension is easy to adjust by simply tightening or loosening the tension control knobs on the supply roll mandrels.
- Variable speed allows thinner films to be run faster, and enables mounting or the use of thicker films, which require slower speeds.
- Independent temperature controls for top and bottom heaters allow the use of different materials on front and back of an image.
Part #: 42B-0008 -
Ledco Digital 44" Dual Hot Roll Laminator & Mounter (4400200P)
- Quality silicone rubber laminating rollers release materials easily and maintain their flexibility for a good edge seal.
- Two sets of rollers keep the film flat and tight while heat laminating so that the automatic fans cool and set the adhesive. When thermal films cool in a slack state, the surface of the lamination is wavy and rippled.
- Supply roll tension is easy to adjust by simply tightening or loosening the tension control knobs on the supply roll mandrels.
- Variable speed allows thinner films to be run faster, and enables mounting or the use of thicker films, which require slower speeds.
- Independent temperature controls for top and bottom heaters allow the use of different materials on front and back of an image.
Part #: 4400200P -
Ledco Digital 60" Laminator & Mounter (60B-0007)
- A Quality silicone rubber laminating rollers release materials easily and maintain their flexibility for a good edge seal.
- Two sets of rollers keep the film flat and tight while heat laminating so that the automatic fans cool and set the adhesive. When thermal films cool in a slack state, the surface of the lamination is wavy and rippled.
- Supply roll tension is easy to adjust by simply tightening or loosening the tension control knobs on the supply roll mandrels.
- Variable speed allows thinner films to be run faster, and enables mounting or the use of thicker films, which require slower speeds.
- Independent temperature controls for top and bottom heaters allow the use of different materials on front and back of an image.
Part #: 60B-0007 -
Ledco Econocraft 30" Laminator Roll Applicator (2030102U)
- A scrap rewind with an adjustable clutch takes up the release liner found on many pressure sensitive films.
- Roller bearings, alloy construction and high quality motors insure a long and trouble-free life for these machines.
- The laminating roller opening is adjustable in seconds and allows operators to work with different thickness materials.
- A variable speed motor control allows operators to apply different materials to different substrates.
- Interchangeable rubber rollers help keep maintenance costs down.
Part #: 2030102U -
Ledco Econocraft 44" Laminator Roll Applicator (2044102U)
- A scrap rewind with an adjustable clutch takes up the release liner found on many pressure sensitive films.
- Roller bearings, alloy construction and high quality motors insure a long and trouble-free life for these machines.
- The laminating roller opening is adjustable in seconds and allows operators to work with different thickness materials.
- A variable speed motor control allows operators to apply different materials to different substrates.
- Interchangeable rubber rollers help keep maintenance costs down.
Part #: 2044102U -
Ledco Econocraft 60" Laminator Roll Applicator (2160103U)
- A scrap rewind with an adjustable clutch takes up the release liner found on many pressure sensitive films.
- Roller bearings, alloy construction and high quality motors insure a long and trouble-free life for these machines.
- The laminating roller opening is adjustable in seconds and allows operators to work with different thickness materials.
- A variable speed motor control allows operators to apply different materials to different substrates.
- Interchangeable rubber rollers help keep maintenance costs down.
Part #: 2160103U -
Ledco Educator 25" School Laminator (9025100D)
- Preset lamination pressure and speed. Makes the machine easier to use and eliminates many possible sources of problems.
- Enclosed laminating and pull rollers. Helps you avoid time-consuming jams and wrap-arounds.
- Forced air cooling. Allows laminating with 3 and 5-mil films, as well as the 1.5 mil film often used by schools. Without a film cooling system, thicker films will warp and ripple because they are still hot and partly melted when they come out of the laminator.
- Fixed-position lamination rollers. Provides a stable platform for uniform roll pressure which provides the highest quality lamination available in a school laminator.
- Attached safety shield. The safety shield is fixed to the machine and is placed so that the operator will naturally put it in the guard position before laminating. The shield is made of clear polycarbonate so users can see their work and will not be tempted to try to laminate without the shield in its safe position.
Part #: 9025100D -
Ledco EP-25 Pre-Mask 25" Tape Applicator 110V (2025100)
- A scrap rewind with an adjustable clutch takes up the release liner found on many pressure sensitive films.
- Roller bearings, alloy construction and high quality motors insure a long and trouble-free life for these machines.
- The laminating roller opening is adjustable in seconds and allows operators to work with different thickness materials.
- A variable speed motor control allows operators to apply different materials to different substrates.
- Interchangeable rubber rollers help keep maintenance costs down.
Part #: 2025100
