Product listing: Challenge Champion 305 TC 30.5" Programmable Paper Cutter (CH-305TC) to Intimus 14.87 6mm x 50mm Cross Cut Level P-3 Industrial Shredder with Baler (14.87-6X50MM)
-
Challenge Champion 305 TC 30.5" Programmable Paper Cutter (CH-305TC) - $33295
- Up to 26 cuts per minute.
- Virtually maintenance-free design.
- Fully-adjustable knife bar gibs (front and rear).
- 30.5" / 77.5 cm cutting width, 4" / 10.2 cm clamp opening.
- Hydraulic clamping and cutting.
Part #: CH-305TC -
Graphic Whizard Crease/Perf/Fold Machine (PT-335CKF) - $33174.36
- Auto Sheet length measurement.
- Automated, or Manual job set-up for custom jobs.
- No limitations between creases/perfs.
- Partial perforation capabilities in both directions.
- 4" deep pile feeder.
Part #: PT-335CKF -
Formax Atlas C300 High-Speed Automatic Creaser and Folder (Atlas-C300) - $32750
- Color touchscreen control panel.
- Fully automatic setup.
- Processes up to 6,000 sheets per hour.
- Handles sheets up to 27.5" x 15.1".
- Contoured floating knives prevent marking of digital prints.
Part #: Atlas-C300 -
Graphic Whizard Automatic Creaser and Folder (PT335-AKF) - $32722.93
- Processes up to a maximum sheet size of 13" x 35" / 33.02 cm x 88.90 cm.
- Efficient vacuum pile feeder.
- Automated job set up with sheet length measuing.
- Easy to replace front loading interchangeable crease/perf dies.
- 3 year parts/electronics warranty.
Part #: PT335-AKF -
Morgana DigiFold Pro High Speed Automatic Creaser and Folder (DigiFold-Pro) - $32500
- SmartScreen touch screen operation.
- 6000 sph.
- 0.015" (approx 150lb cover)*.
- Alpha-numeric memory.
- PosiFeed feed system.
Part #: DigiFold-Pro -
Truline Preferred Pack 2 Belt Fully Automatic Side Sealer (Int-20) - $32500
- Touch screen automatically adjusts side seal, inverting head and infeed conveyor.
- Option 3' or 6' flighted or belted infeed conveyors.
- Front load film cradle with adjustable pin-perf wheels.
- No mantaince side seal, seals virtually all films.
- Seal Area: 20" Cross Seal x 6"H
Part #: Int-20 -
Royal Sovereign 67" Calender Heat Transfer System With 10" Oil Drum (CX-181) - $32117.65
- Extra-long infra-red quartz heated drum to ensure complete heat distribution and coverage.
- Finely tuned sensors to ensure consistent temperatures throughout the transfer process.
- Universal core adapters and shaft-less unwinding technology.
- Easy to reach front and rear facing emergency stops.
- Emergency Reverse.
Part #: CX-181 -
Truline Preferred Pack Inline Fully Automatic Sleeve Wrapper with Attached Tunnel (SFE-800NF) - $31500
- Speed: 5 to 20 PPM (Depending on product size and film thickness.)
- Electrical: 220 Volt, 3 Phase, 60 Amp
- Seal Size: 29.5"
- Max Roll Width: 27"
- Max Package Height: 14"
Part #: SFE-800NF -
Brackett Chipur 21" Automatic Chipboard Inserter (BK-2100MA) - $31250
- Automatic chipboard insertion for roll-to-sheet presses.
- Feeds chipboard into the lapstream delivery (shingled sheets) of your web press at precise, predetermined intervals as frequently as every 25 sheets.
- Utilizes a series of vacuum separator units which lift up printed sheets in the delivery stream momentarily to allow chipboard insertion.
- Installs and adjusts in minutes to fit the height of your press - a Diddle or other popular roll-to-sheet press.
- Replaces hand inserting - or in some installations, take the place of an expensive, cumbersome, limited application inserter.
Part #: BK-2100MA -
Ledco Heavy Duty 38" Laminator with Stand (7038200A) - $30887
- Intelligent heat controllers display both the set temperature and the actual temperature. The microprocessor in the control quickly learns to anticipate the heat demand of each job and keeps the actual temperature within a few degrees of the set temperature.
- Laminating and pull rollers are covered with quality silicone rubber for superior release quality, higher lamination quality and easier cleaning. The laminating rollers and pull rollers are interchangeable to help keep maintenance costs down.
- Pneumatic power opens or closes the laminating and pull rollers and gives you a precise and independent control of roll pressure. A compressor is built in so that shop air is not required.
- Removable heat shoes are Teflon coated to reduce film abrasion. They are easily unplugged and removed to clean or replace the laminating rollers.
- Built-in retractable slitters save an enormous amount of cutting time by trimming away side scrap during the lamination process. The two heads can be adjusted independently with great precision.
Part #: 7038200A -
HSM FA500.3c Cross-cut Industrial Shredder (HSM1991) - $30825.52
- Order number: HSM1991
- EAN Code: 4026631033206
- Shredder material: Paper, CD/DVD, Floppy Disk, USB Stick, Paper Clip and Credit/Store Cards
- Cutting type: Cross Cut
- Security level (DIN 66399): P-3 (Old level 2)
Part #: HSM1991 -
GBC DigiCoil Automatic Color Coil Inserter (0340000000) - $30749
- LCD panel directs operator through each step of the binding process.
- Accommodates 4:1 coils from 8mm to 33mm.
- Secure coil crimping.
- Small footprint - takes less space.
- No air required.
Part #: 0340000000 -
Royal Sovereign Rollover Classic 55" x 315" Flatbed Applicator for Mounting and Laminating (10814) - $30073
- Key Features:
- Ideal for rigid panel application and laminating digital prints.
- Substrates up to 3.5 inches can be handled for perfectly flat applications without bubbles or creases.
- Applying digital prints and other self-adhesive applications on rigid panels such as composite board, acrylic, aluminum etc., is just one of the areas where Rollover Classic reveals its excellent properties in results and operations.
- Being able to comfortably operate the laminator with one hand while having free access to roller, media and tabletop, results in smooth and effective handling.
Part #: 10814 -
Ledco 30" Automatic Laminate Cutter 110V (C300110-B) - $30057.5
- Variable speed up to 150 feet per minute.
- Adjustable speed even during operation.
- Feed table support for precise guidance of web.
- Two-sided cutting blades for twice the lifespan.
- Self-sharpening shear cutting blades.
Part #: C300110-B -
Morgana DigiBook 150 Automatic PUR Perfect Binding Machine (DigiBook-150) - $29990
- Up to 100 books per hour.
- Touch screen operation.
- Automatic clamp.
- Binding length (spine) from 4.3" up to 14.9".
- Spine thickness from 0.07" to 1.96".
Part #: DigiBook-150 -
Rhin-O-Tuff Tornado Autopunch EX Modular Interchangeable Die Binding Punch (TEX110) - $29950
- World’s First Automated Collating Punch using Patented BDT Tornado Technology. A single off-line automated collation and punching platform to meet the needs of your on-demand print environment with a quick return on investment.
- Advanced Media Handling Technology. Powered by BDT’s patented Tornado Technology to separate, lift and transport the widest range of media, including printed media and other book components like covers, tabs and inserts reliably minimizing downtime.
- Widest Media Range in the Industry. The system handles media from 60gsm – 312gsm, including light porous/heavy coated print media and specialty binding media like plastics, vinyl, and textures.
- Automated Interposing of Covers/Index Tabs/Inserts. Two Interposer Bins hold up to .75" (19mm) of media, auto-collating front/back covers, inserts and index tabs into the book stack prior to punching. No manual collation required.
- Accommodates Mixed Media Run on Digital/Offset Printers. High-Capacity Main Bin holds up to 2500 sheets, including mixed media.
Part #: TEX110 -
Spiel Sterling Digipunch High Speed Automatic Punch (SPL-DP14) - $29950
- Paper Stabber. The stabber can be set to stab 3 - 17 sheets. This is more consistent than punches that rely on gravity to feed the paper.
- Die. The dies can be changed in seconds. Pull pins result in faster changeovers between sheet sizes.
- Registration Table. This registers the paper on all four sides, using side guides and rear stops. The rear stops accommodate sheets intermixed with tabs.
- Stacker. The receding stacker operates in tandem with the feeder, each of which can hold five reams of paper. The machine stops when the stacker is full.
- Touch Screen. The Digipunch’s touch screen computer guides you through the entire punching process. You choose the paper size from a variety of presets or enter a custom size. Choose how many sheets you want to punch per lift, punching less for problem stocks. The computer will track the maintenance cycle of each die that is used, prompting when to lubricate or sharpen the die. It also prompts the operator when safety covers are open. The manual is contained in the touch screen computer with a variety of tips and tricks to make the operation of the machine quick and easy.
Part #: SPL-DP14 -
Vivid Matrix 20" Pneumatic Single Sided Roll Laminator (MX-530P) - $29690
- Pneumatic pressure.
- Retrofits to existing models.
- Easy-to-use control panel.
- Anti-curl technology.
- Semi-automatic feed.
Part #: MX-530P -
GBC 2064Ct Roll Laminator (1880008) - $29521
- LCD display for pressure and temperature eliminate guesswork
- Bi-directional productivity allows jobs to be run consecutively
- Film shafts swing out for easy loading and unloading
- Heat rollers and pull rollers are independently adjustable
- With a mechanical roller adjustment, heat rollers are infinitely variable to 1"
Part #: 1880008 -
Tec Lighting TruCoat 21" Auto Feed UV Coater (TRUVF-21FD) - $29205
- Apply gloss-satin and matte coatings.
- Coat toner based, offset or inkjet with ease.
- Quick change textured rollers for an array of finishes.
- Speeds of up o 4,800SPH.
- From start to coating in less than 5 Minutes.
Part #: TRUVF-21FD -
Afinia Label DLF-1100 Table-Top Digital Label Finisher for L801 Printer (AFN26611) - $28995
- Capabilities - Lamination, Liner removal, Contour cutting, Waste removal, Slitting and Rewinding.
- Built around a proven industry-standard, plotter-style cutting mechanism for maximum accuracy and dependability.
- Quick printers and brands will be free to create and print unusually-shaped labels
- Features a compact, table-top design and measures 31?w x 22?h x 21?d (79cm x 56cm x 53cm) and can fit into almost any setting.
- Works directly from your design software with its convenient plug-in for Illustrator and CorelDraw.
Part #: AFN26611 -
Challenge Champion 305 Manual Backgauge 30.5" Electric Paper Cutter (CH-305X) - $28995
- 30-1/2" Cutting Width, 4" Clamp Opening
- Hydraulic Clamping & Cutting
- Adjustable Clamp Pressure
- Manual Foot Pedal Clamping
- Backgauge Position Indicator
Part #: CH-305X -
James Burn Lhermite DocuPunch Plus Automatic Binding Punch (04DOCUPUNCH) - $28730
- Speeds of up to 76,500 sheets per hour with clean, perfect holes for finishing.
- Adjustable pick thickness from 0.4 to 1.0 mm, to maximize production and offer trouble free operation on a wide range of paper stocks.
- Digital LCD touch pad control that is icon based for simple operation.
- Punches a wide variety of paper stocks, covers, and even tabbed sheets in sizes from 5.5" x 5.5" up to 13" x 12" kept in perfect pre-collated order.
- Easy-to-Use hands-free operation allows you to simply load the tray, push a button and walk away. No special training or personnel required.
Part #: 04DOCUPUNCH -
Truline Preferred Pack Semi Automatic Sleeve Wrapper with Attached Tunnel (SFE-1100SA) - $28250
- Speed: 5 to 15 PPM (Depending on product size and film thickness.)
- Electrical: 220 Volt, 3 Phase, 70 Amp
- Seal Size: 41 3/4"
- Max Roll Width: 39"
- Max Package Length: 19.5"
Part #: SFE-1100SA -
James Burn CB30QS 17" Automatic Coil Inserter and Crimper (04JBCB30QS17) - $27999
- Setup is quick and no tools are required for basic setup and operation.
- So easy to use that it automatically inserts pre-cut coil lengths into pre-punched books and simultaneously crimps both ends in a single operation.
- Comes with 8 to 20mm Crimper Head
- Production speeds up to 600 books per hour.
- Comes standard as .2475 pitch and requires a 5 x 4mm oval punch die. (Optional 3:1 pitch available which requires a 6.5 x 5.5 mm oval punch dies for 22mm to 30mm size coil.)
Part #: 04JBCB30QS17 -
HSM CP 4988 PET Crusher Baler Combo (HSMCP4988) - $27998.99
- Low space requirement
- Manual and automatic filling possible
- Crusher rollers made of specially hardened and ground steel, impervious and sturdy – for a long service life
- Scraper system removes the compressed plastic bottles reliably from the crusher rollers
- Dosing shaft with several paddles ensures that the PET bottles are reliably fed to the rollers
Part #: HSMCP4988 -
Formax ColorMax T6 Digital Color Multimedia Printer with Conveyor, Feeder and Sheet Trays (ColorMaxT6-P) - $27995
- Speed: Up to 50 ppm color/mono, up to 45 ppm (CMYK over White), up to 17ppm (CMYK plus Clear).
- Multi-Level LED Print Heads: Control the amount of toner applied to each 1200-dpi dot, preserving fine image detail and maximizing color fidelity across the entire document.
- Microfine Dry Toner: Sharp, crisp output, with a durable high-quality finish, ideal for envelopes.
- Flexibility: Prints on a wide range of envelopes and media, including magnetic, polyester, transparent film, and heavy stock up to 360gsm.
- High-Capacity Toner Cartridges: Up to 38,000 pages.
Part #: ColorMaxT6-P -
Royal Sovereign Rollover Classic 65" x 236" Flatbed Applicator for Mounting and Laminating (10617) - $27726
- Key Features:
- Ideal for rigid panel application and laminating digital prints.
- Substrates up to 3.5 inches can be handled for perfectly flat applications without bubbles or creases.
- Applying digital prints and other self-adhesive applications on rigid panels such as composite board, acrylic, aluminum etc., is just one of the areas where Rollover Classic reveals its excellent properties in results and operations.
- Being able to comfortably operate the laminator with one hand while having free access to roller, media and tabletop, results in smooth and effective handling.
Part #: 10617 -
Intimus 14.87 3.8mm x 40mm Level P-4 Cross Cut Industrial Shredder with Baler (699931+475901) - $27412
- The useful supplement to the large document shredder: shredded material is automatically compressed into compact bales.
- Shredder and baler operate in tandem.
- Shredder features see Model 14.95 S.
- Shredder loading can be continued while baler is compressing the material.
- Push button control for bale ejection.
Part #: 699931+475901 -
Intimus 14.87 6mm x 50mm Cross Cut Level P-3 Industrial Shredder with Baler (14.87-6X50MM) - $27412
- The useful supplement to the large document shredder: shredded material is automatically compressed into compact bales.
- Shredder and baler operate in tandem.
- Shredder features see Model 14.95 S.
- Shredder loading can be continued while baler is compressing the material.
- Push button control for bale ejection.
Part #: 14.87-6X50MM
