Product listing: Manual TIMEbadge Expiring Half Day Badge FRONTpart - Visitor - 1000pk - TEMPbadges (06403) to Drytac MHL Lustre UV 3mil 51" x 500' Low Temp Laminating Film - Low Melt (MLD51503)

Page
View by: Title (A-Z)  |  Title (Z-A)  |  Price (High-to-Low)  |  Price (Low-to-High)  |  Popularity  |  Best Sellers  |  Category  |  Product Number
  1. Manual TIMEbadge Expiring Half Day Badge FRONTpart - Visitor - 1000pk - TEMPbadges (06403), Id Accessories

      Type: Visitor Half Day Attachment Method: FRONTpart to be attached to BACKpart (sold separately) Size: 1 15/16inchx2 7/8inch (49mmx73mm) Quantity: 1000 Per Pack Part Number: 06403
    Part #: 06403

    $349.59

  2. Thermal-Printable ONEstep TIMEbadge Expiring Badge - Blank - 500pk - TEMPbadges (02011), Id Accessories

      Type: Blank Attachment Method: Adhesive Back Size: 1 7/8inchx2 7/8inch (47mmx73mm) Quantity: 500 Per Pack Part Number: 02011
    Part #: 02011

    $200.99

  3. Manual ONEstep TIMEbadge Expiring Badge Clip-on - Visitor - 500pk - TEMPbadges (02014), Id Accessories

      Type: Visitor Attachment Method: Clip-on Size: 2 5/8inchx3inch (67mmx76mm) Quantity: 500 Per Pack Part Number: 02014
    Part #: 02014

    $246.39

  4. Manual ONEstep TIMEbadge Expiring Badge - Vendor - 500pk - TEMPbadges (02007), Id Accessories

      Type: Vendor Attachment Method: Adhesive Backing Size: 1 7/8inchx2 7/8inch (47mmx73mm) Quantity: 500 Per Pack Part Number: 02007
    Part #: 02007

    $209.69

  5. Manual ONEstep TIMEbadge Expiring Badge - Contractor - 500pk - TEMPbadges (02005), Id Accessories

      Type: Contractor Attachment Method: Adhesive Backing Size: 1 7/8inchx2 7/8inch (47mmx73mm) Quantity: 500 Per Pack Part Number: 02005
    Part #: 02005

    $198.09

  6. Manual ONEstep TIMEbadge Expiring Badge - Temporary - 500pk - TEMPbadges (02004), Id Accessories

      Type: Temporary Attachment Method: Adhesive Backing Size: 1 7/8inchx2 7/8inch (47mmx73mm) Quantity: 500 Per Pack Part Number: 02004
    Part #: 02004

    $198.09

  7. Manual ONEstep TIMEbadge Expiring Badge - Visitor - 500pk - TEMPbadges (02003), Id Accessories

      Type: Visitor Attachment Method: Adhesive Backing Size: 1 7/8inchx2 7/8inch (47mmx73mm) Quantity: 500 Per Pack Part Number: 02003
    Part #: 02003

    $198.09

  8. Printable TEMPcard Expiring PVC Badge - 100pk - TEMPbadges (08172), Id Accessories

      Type: Printable 30mil Plastic - Blank Attachment Method: Badge holder or slot punch required Size: 2.125inchx3.375inch (54mmx85mm) Quantity: 100 Per Pack Part Number: 08172
    Part #: 08172

    $115.09

  9. GBC 1/4" Black Linen ThermaBind Covers (100pk) - Thermal Covers (2516315), Bookbinding Supplies

      Style: GBC Linen Therm-A-Bind Covers Color: Black Thickness: 1/4inch (GBC ThermaBind Covers are actually 1/16inch larger than their size indicates) Capacity: 25-60Sheets Part Number: 2516315
    Part #: 2516315

    $226.59

  10. 3/8" White Grain ThermaBind Covers (25pk) - GBC (2513532), Bookbinding Supplies

      Style: GBC Grain Therm-A-Bind Covers Color: White Thickness: 3/8inch (GBC ThermaBind Covers are actually 1/16inch larger than their size indicates) Capacity: 55-90Sheets Part Number: 2513532
    Part #: 2513532

    $57.09

  11. 1/4" White Grain ThermaBind Covers (25pk) - GBC (2513531-X), Bookbinding Supplies

      Style: GBC Grain Therm-A-Bind Covers Color: White Thickness: 1/4inch (GBC ThermaBind Covers are actually 1/16inch larger than their size indicates) Capacity: 25-60Sheets Part Number: 2513531
    Part #: 2513531-X

    $57.09

  12. 1/8" White Grain ThermaBind Covers (25pk) - GBC (2513530X), Bookbinding Supplies

      Style: GBC Grain Therm-A-Bind Covers Color: White Thickness: 1/8inch (GBC ThermaBind Covers are actually 1/16inch larger than their size indicates) Capacity: 5-30Sheets Part Number: 2513530
    Part #: 2513530X

    $57.09

  13. 1/16" White Grain ThermaBind Covers 25pk - GBC (2513529X), Bookbinding Supplies

      Style: Grain Therm-A-Bind Covers Color: White Thickness: 1/16inch Capacity: 1-10Sheets Part Number: 2513529
    Part #: 2513529X

    $57.09

  14. Thermal Binding Glue Strips for Create Your Own Covers - 50pk (BIADSTRIP11), Bookbinding Supplies

      Width: 8.5 inches length: 11 inches Thickness: 1mm Product Number: BIADSTRIP11
    Part #: BIADSTRIP11

    $61.49

  15. Fellowes Helios 30 Thermal Binding Machine (5219301), Binding Machines


      Ideal for medium duty thermal binding projects or desktop use
      Binds up to 300 sheets in one step
      1-3 minute thermal binding cycle with 4-minute heat-up time
      HeatShield safety barrier prevents accidental contact with the heating plate
      Manual document measure and LED control panel ensure ease of use
      Audio/visual indicators signal when machine is ready for thermal binding or job is complete
      Auto shut-off safety feature prevents overheating.
      Folds flat for storage; for use with thermal binding covers only
      LED control panel
      Auto shut-off safety feature
      300 page binding capacity
      2 Year Manufacturer Warranty ßÃЊ“Á
    Part #: 5219301

    $114.48

  16. Fellowes Helios 60 Thermal Binding Machine (5219501), Binding Machines


      Ideal for large offices - features 1-step, worry-free thermal binding!
      Binds up to 600 sheets in one step
      1-3 minute thermal binding cycle with 4-minute heat-up time
      Auto document thickness detector selects thermal binding settings for the user
      HeatShield safety barrier prevents accidental contact with the heating plate
      LED control panel ensures advanced thermal binding machine is user-friendly
      Audio/visual indicators signal when machine is ready or job is complete
      Auto shut-off safety feature prevents overheating.
      Folds flat for storage; for use with thermal binding covers only
      LED control panel
      Auto document thickness detector
      600 page binding capacity
      2 Year Manufacturer Warranty ßÃЊ“Á
    Part #: 5219501

    $160.29

  17. Pro-Bind 1000 Professional Thermal Binding Machine (PB-1000), Binding Machines


      Hard Cover & Soft Cover Binding Capabilities
      Simple One-Touch Operation
      Convenient Built-In Cooling Rack
      Energy Saving Mode
      Dimensions: 15.5" W x 8-7/8" D x 4-1/4" H
      Power-Supply: 120V / 60hz
      Binding Throat: 12" x 1-1/4"
      Binding Capacity : 3/4"
      Manufacturer: Pro-Bind
      Weight: 2 lbs
      Part Number: PB-1000
      Warranty: 1 Year Manufacturer Warranty
      Simple one-touch operation
      Convenient built-in cooling rack
      3/4" binding capacity
      1 Year Manufacturer Warranty ßÃЊ“Á
    Part #: PB-1000

    $149.00

  18. Pro-Bind 2000 Professional Thermal Binding Machine (PROBIND2000), Binding Machines


      All Metal Construction
      Auto Shut Off
      14.75'' Binding Length
      Binds Multiple Documents At One Time
      Circuit Board Mounted on frame away from heating unit
      Cycle Time 30 seconds Soft Cover & 60 seconds for Hard Cover
      15 Degree Angle on Heating Plate - Allows for less spreading of sheets in binding process
      Factory Set Heat - Fully electronically programmable for changes in paper material or content substraights - 300 to 350 degrees
      No Warm Up Required
      One Button Operation
      1/16'' to 2'' Binding Capacity
      Manufacturer: Pro-Bind
      Weight: 10 lbs
      Part Number: PROBIND2000
      Warranty: 1 Year Manufacturer Warranty
      Auto Shut Off
      Binds multiple documents at one time
      2" binding capacity
      1 Year Manufacturer Warranty ßÃЊ“Á
    Part #: PROBIND2000

    $695.00

  19. Perfect Bind T-30 Thermal Binding Machine - Tamerica (MYT30), Thermal Binding


      Durable light gray plastic shell
      Easy operation with buzzer and indicator light.
      Built in cooling rack for increased performance
      Maximum Spine Width: 1"
      Maximum Spine Length: 11.8"
      Part Number: MYT30
      Warranty: 3 Month Manufacturer Warranty
      Easy operation with buzzer and indicator light
      Built in cooling rack
      Can handle up to 1" total thickness
      3 Month Manufacturer Warranty ßÃЊ“Á
    Part #: MYT30

    $78.00

  20. Drytac MHL Impervo UV 10mil 38" x 250' Hardcoat Laminating Film - UV Protected (MLL38210), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MLL38210

    $1067.54

  21. Drytac MHL Impervo UV 10mil 25" x 250' Hardcoat Laminating Film - UV Protected (MLL25210), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MLL25210

    $702.28

  22. Drytac MHL Impervo UV 5mil 51" x 250' Hardcoat Laminating Film - UV Protected (MLL51205), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MLL51205

    $855.55

  23. Drytac MHL Impervo UV 5mil 43" x 250' Hardcoat Laminating Film - UV Protected (MLL43205), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MLL43205

    $721.35

  24. Drytac MHL Impervo UV 5mil 38" x 250' Hardcoat Laminating Film - UV Protected (MLL38205), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MLL38205

    $637.46

  25. Drytac MHL Impervo UV 5mil 25" x 250' Hardcoat Laminating Film - UV Protected (MLL25205), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MLL25205

    $426.13

  26. Drytac MHL Matt UV 3mil 61" x 500' Low Temp Thermal Laminating Film - Low Melt (MM61503), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MM61503

    $472.60

  27. Drytac MHL Matt UV 3mil 51" x 500' Low Temp Thermal Laminating Film - Low Melt (MM51503), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MM51503

    $395.14

  28. Drytac MHL Matt UV 3mil 43" x 500' Low Temp Thermal Laminating Film - Low Melt (MM43503), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MM43503

    $333.14

  29. Drytac MHL Matt UV 3mil 38" x 500' Low Temp Thermal Laminating Film - Low Melt (MM38503), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MM38503

    $294.39

  30. Drytac MHL Lustre UV 3mil 51" x 500' Low Temp Laminating Film - Low Melt (MLD51503), Laminating Film

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MLD51503

    $396.84

Items 1-15 of 22

Display Type List Grid
Page:   1   10   20   30   40   50   60   70   80   89   90   91   92   93   94   95   96   97   98   99   100   101   102   103   104   105   106   107   108   109   110   111   112   113   114   115   116   117   118   120   130   140   150   160   170   180   190   200   300   304