Product listing: Drytac Trimount 42.5" x 150' Dry Mounting Tissue (Rolls) - Mounting Adhesives (TR42150) to Drytac MediaShield Heatset Emerytex UV 5mil 51" x 328' Overlaminate (ET51328)

Page
View by: Our Choices  |  Best Seller  |  Title (A-Z)  |  Title (Z-A)  |  Popularity  |  All-Round Favorites  |  Price (High-to-Low)  |  Price (Low-to-High)
  1. Drytac Trimount 42.5" x 150' Dry Mounting Tissue (Rolls) - Mounting Adhesives (TR42150)


      Size: 42.5" x 150'
      Carrier: Paper/off-white
      Adhesive Bond: Permanent
      Adhesive Base: Solvent acrylic
      Initial Tack: None
      Precessing Temperature: 85 DegreesC-100 Degrees (185 DegreesF-212 DegreesF)
      Release Liner: None
      Dwell Time: 30-90 seconds
      Part Number: TR42150
      Film Finish: Mounting Tissue
      Thickness: 3 mil
      Dwell Time: 30-90 seconds
      Hot or Cold: Hot ßÃЊ“Á
    Part #: TR42150

    $239.17

  2. Drytac Trimount 41" x 300' Dry Mounting Tissue (Rolls) - Mounting Adhesives (TR41300)


      Size: 41" x 300'
      Carrier: Paper/off-white
      Adhesive Bond: Permanent
      Adhesive Base: Solvent acrylic
      Initial Tack: None
      Precessing Temperature: 85 DegreesC-100 Degrees (185 DegreesF-212 DegreesF)
      Release Liner: None
      Dwell Time: 30-90 seconds
      Part Number: TR41300
      Film Finish: Mounting Tissue
      Thickness: 3 mil
      Dwell Time: 30-90 seconds
      Hot or Cold: Hot ßÃЊ“Á
    Part #: TR41300

    $455.69

  3. Drytac Trimount 41" x 150' Dry Mounting Tissue (Rolls) - Mounting Adhesives (TR41150)


      Size: 41" x 150'
      Carrier: Paper/off-white
      Adhesive Bond: Permanent
      Adhesive Base: Solvent acrylic
      Initial Tack: None
      Precessing Temperature: 85 DegreesC-100 Degrees (185 DegreesF-212 DegreesF)
      Release Liner: None
      Dwell Time: 30-90 seconds
      Part Number: TR41150
      Film Finish: Mounting Tissue
      Thickness: 3 mil
      Dwell Time: 30-90 seconds
      Hot or Cold: Hot ßÃЊ“Á
    Part #: TR41150

    $239.17

  4. Drytac Trimount 36.5" x 300' Dry Mounting Tissue (Rolls) - Mounting Adhesives (TR36300)


      Size: 36.5" x 300'
      Carrier: Paper/off-white
      Adhesive Bond: Permanent
      Adhesive Base: Solvent acrylic
      Initial Tack: None
      Precessing Temperature: 85 DegreesC-100 Degrees (185 DegreesF-212 DegreesF)
      Release Liner: None
      Dwell Time: 30-90 seconds
      Part Number: TR36300
      Film Finish: Mounting Tissue
      Thickness: 3 mil
      Dwell Time: 30-90 seconds
      Hot or Cold: Hot ßÃЊ“Á
    Part #: TR36300

    $149.48

  5. Drytac Trimount 16" x 20" Dry Mounting Tissue - 100 Sheets - Mounting Adhesives (TR3215)


      Size: 16" x 20"
      Carrier: Paper/off-white
      Adhesive Bond: Permanent
      Adhesive Base: Solvent acrylic
      Initial Tack: None
      Precessing Temperature: 85 DegreesC-100 Degrees (185 DegreesF-212 DegreesF)
      Release Liner: None
      Dwell Time: 30-90 seconds
      Part Number: TR3215
      Film Finish: Mounting Tissue
      Thickness: 3 mil
      Dwell Time: 30-90 seconds
      Hot or Cold: Hot ßÃЊ“Á
    Part #: TR3215

    $121.29

  6. Drytac Trimount 11" x 14" Dry Mounting Tissue - 100 Sheets - Mounting Adhesives (TR3210)


      Size: 11" x 14"
      Carrier: Paper/off-white
      Adhesive Bond: Permanent
      Adhesive Base: Solvent acrylic
      Initial Tack: None
      Precessing Temperature: 85 DegreesC-100 Degrees (185 DegreesF-212 DegreesF)
      Release Liner: None
      Dwell Time: 30-90 seconds
      Part Number: TR3210
      Film Finish: Mounting Tissue
      Thickness: 3 mil
      Dwell Time: 30-90 seconds
      Hot or Cold: Hot ßÃЊ“Á
    Part #: TR3210

    $70.62

  7. Drytac SureTac White 51" x 300' Premium PS Mounting Adhesive (PSA29510)


      Roll Width: 51"
      Roll Length: 300'
      Core Size: 3"
      Laminate Type: SureTac White Premium Mounting Adhesive
      Filmic Carrier: 1.1mil (28 micron) white polypropylene
      Adhesive Bond: Permanent
      Initial Tack : High
      Application Speed: 1' - 8' per minute
      Adhesive Base: Solvent Acrylic
      Application Temp: Room Temperature - 120F (49 C)
      Release Liner: Moisture Stable Lay-Flat Paper (96 lbs) (157 gsm)
      Film Finish: White Polypropylene
      Core Size: 3"
      Thickness: 1.1 mil
      Hot or Cold: Hot ßÃЊ“Á
    Part #: PSA29510

    $870.75

  8. Drytac Push/Pull Hangers (100pk) - Laminating Accessories (ACC9700)


      Quantity: Package of 100
      Part Number: ACC9700
      Quantity: Package of 100
      Capable to provide a quick and easy hanging solution in minutes
      Art and graphics with foam board can be mounted securely and firmly with the Drytac Push/Pull Hinged Hangers
      Part Number: ACC9700 ßÃЊ“Á
    Part #: ACC9700

    $71.94

  9. Drytac Protac Scribe 2.5mil 25.5" x 150' Dry-Erase PS Overlaminate - Pressure Sensitive (PSC25150)


      Film Width: 25.5"
      Film Length: 164'
      Film Thickness: 2.5mil
      Core Size: 3"
      Finish: Dry-erase / Gloss
      Base Film: 1.6 mil (40 micron)
      Adhesive: 1.0mil Solvent Acrylic
      Initial Tack: High
      Maximum Bond: 24 Hours
      Application Speed: 1' - 7' per minute
      Application Temperature: Room Temperature - 120 F
      Release Liner: Moisture Stable Paper (100gsm)
      Film Finish: Gloss
      Core Size: 3"
      Film Thickness: 2.5mil
      Hot or Cold: Cold ßÃЊ“Á
    Part #: PSC25150

    $195.23

  10. Drytac Protac Polycarbonate UV 10.0mil 51" x 75' PS Overlaminate - Pressure Sensitive (PPC51075-10)


      Film Width: 51"
      Film Length: 75'
      Film Thickness: 10.0mil
      Core Size: 3"
      Finish: Polycarbonate (Pebble Textured Velvet Matte)
      Base Film: 10.0 mil (250 micron) polycarbonate
      Adhesive: 2.0 mil solvent acrylic
      Initial Tack: High
      Application Speed: 1' - 4' per minute
      Application Temperature: Room Temperature - 90 F
      Release Liner: Clear Polyester
      Film Finish: Matte
      Core Size: 3"
      Film Thickness: 10.0mil
      Hot or Cold: Hot ßÃЊ“Á
    Part #: PPC51075-10

    $600.54

  11. Drytac Protac High Gloss UV 5.0mil 51" x 150' PS Overlaminate - Pressure Sensitive (PLHG3515)


      Film Width: 51"
      Film Length: 150'
      Film Thickness: 5.0mil
      Core Size: 3"
      Finish: Gloss
      Base Film: 4 mil (100 micron) Polyester
      Adhesive: 1.0mil solvent acrylic
      Initial Tack: High
      Application Speed: 1' - 6' per minute
      Application Temperature: Room Temperature - 120 F
      Release Liner: Clear Polyester Film
      Film Finish: Gloss
      Core Size: 3"
      Film Thickness: 5.0mil
      Hot or Cold: Hot ßÃЊ“Á
    Part #: PLHG3515

    $620.55

  12. Drytac Protac High Gloss UV 5.0mil 38" x 150' PS Overlaminate - Pressure Sensitive (PLHG3385)


      Film Width: 38"
      Film Length: 150'
      Film Thickness: 5.0mil
      Core Size: 3"
      Finish: Gloss
      Base Film: 4 mil (100 micron) Polyester
      Adhesive: 1.0mil solvent acrylic
      Initial Tack: High
      Application Speed: 1' - 6' per minute
      Application Temperature: Room Temperature - 120 F
      Release Liner: Clear Polyester Film
      Film Finish: Gloss
      Core Size: 3"
      Film Thickness: 5.0mil
      Hot or Cold: Hot ßÃЊ“Á
    Part #: PLHG3385

    $470.20

  13. Drytac ML25 Manual Hand Crank Pressure Sensitive Cold Mount Roll Laminator (DTML25)


      Max Laminating Width: 25.5 inches (648mm)
      Width: 27.375 inches (695.3mm)
      Depth: 24.5 inches (622mm)
      Height: 10.25 inches (260mm)
      Roller Diameter: 2.5 inches (63.5mm)
      Max Nip Opening: 1" (25 mm)
      Warranty: 1 Year Manufacturer Warranty
      Weight: 32 lbs (14 kg)
      Max Nip Opening: 1" (25 mm)
      Max Laminate Width: 25.5"
      Max Film Thickness: 10 mil
      Hot or Cold: Cold ßÃЊ“Á
    Part #: DTML25

    $348.99

  14. Drytac MHL Scribe 3mil 51" x 500' Dry Erase Laminating Film - Pressure Sensitive (MS51503)

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MS51503

    $163.89

  15. Drytac MHL Matt UV 3mil 61" x 500' Low Temp Thermal Laminating Film - Low Melt (MM61503)

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MM61503

    $472.60

  16. Drytac MHL Lustre UV 3mil 38" x 500' Low Temp Laminating Film - Low Melt (MLD38503)

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MLD38503

    $295.69

  17. Drytac MHL Impervo UV 5mil 38" x 250' Hardcoat Laminating Film - UV Protected (MLL38205)

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MLL38205

    $637.46

  18. Drytac MHL Gloss 5mil 61" x 250' Low Temp Thermal Laminating Film - Low Melt (MGD61205)

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MGD61205

    $358.26

  19. Drytac MHL Gloss 5mil 43" x 250' Low Temp Thermal Laminating Film - Low Melt (MGD43205)

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MGD43205

    $252.55

  20. Drytac MHL Gloss 5mil 25" x 250' Low Temp Thermal Laminating Film - Low Melt (MGD25205)

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MGD25205

    $146.83

  21. Drytac MHL Gloss 3mil 51" x 500' Low Temp Thermal Laminating Film - Low Melt (MGD51503)

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MGD51503

    $308.07

  22. Drytac MHL Gloss 3mil 43" x 500' Low Temp Thermal Laminating Film - Low Melt (MGD43503)

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MGD43503

    $259.71

  23. Drytac MHL Gloss 3mil 38" x 500' Low Temp Thermal Laminating Film - Low Melt (MGD38503)

      MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.
    Part #: MGD38503

    $151.02

  24. Drytac MHA 41" x 328' Multi Heat Activated Mounting Adhesive (MHA41328)


      Film Width: 41"
      Film Length: 328'
      Core Size: 3"
      Filmic Carrier: None
      Adhesive Bond: Permanent:
      Initial Tack: Very Low
      Application Speed: 1' - 8' (0.3m - 2.5m) per minute
      Adhesive Base: Solvent acrylic heat-activated
      App. Temperature: 185 F - 220 F
      Release Liner: Moisture Stable Paper (100 gsm)
      Film Finish: Mounting Adhesive
      Core Size: 3"
      Adhesive Bond: Permanent:
      Hot or Cold: Hot ßÃЊ“Á
    Part #: MHA41328

    $562.34

  25. Drytac MHA 25.5" x 328' Multi Heat Activated Mounting Adhesive (MHA25328)


      Film Width: 25.5"
      Film Length: 328'
      Core Size: 3"
      Filmic Carrier: None
      Adhesive Bond: Permanent:
      Initial Tack: Very Low
      Application Speed: 1' - 8' (0.3m - 2.5m) per minute
      Adhesive Base: Solvent acrylic heat-activated
      App. Temperature: 185 F - 220 F
      Release Liner: Moisture Stable Paper (100 gsm)
      Film Finish: Mounting Adhesive
      Core Size: 3"
      Adhesive Bond: Permanent:
      Hot or Cold: Hot ßÃЊ“Á
    Part #: MHA25328

    $357.52

  26. Drytac MediaTac 51" x 164' Pressure Sensitive Aqueous Adhesive - Mounting Adhesives (PSA26-51164)


      Roll Width: 51"
      Roll Length: 164'
      Core Size: 3"
      Laminate Type: MediaTac Adhesive
      Filmic Carrier: 0.5 mil (13 micron) clear polyester
      Adhesive Bond: Permanent
      Adhesive Base: High
      Application Speed: 1' - 8' per minute
      Application Temp: Room Temperature - 120F (49 C)
      Release Liner: Moisture Stable Paper (60 lbs) (100 gsm)
      Film Finish: Clear Polyester
      Core Size: 3"
      Thickness: 0.5 mil
      Hot or Cold: Hot ßÃЊ“Á
    Part #: PSA26-51164

    $317.81

  27. Drytac MediaTac 38" x 164' Pressure Sensitive Aqueous Adhesive - Mounting Adhesives (PSA26-38164)


      Roll Width: 38"
      Roll Length: 164'
      Core Size: 3"
      Laminate Type: MediaTac Adhesive
      Filmic Carrier: 0.5 mil (13 micron) clear polyester
      Adhesive Bond: Permanent
      Adhesive Base: High
      Application Speed: 1' - 8' per minute
      Application Temp: Room Temperature - 120F (49 C)
      Release Liner: Moisture Stable Paper (60 lbs) (100 gsm)
      Film Finish: Clear Polyester
      Core Size: 3"
      Thickness: 0.5 mil
      Hot or Cold: Hot ßÃЊ“Á
    Part #: PSA26-38164

    $270.16

  28. Drytac MediaShield Heatset Satinex UV 3mil 51" x 328' Overlaminate (SX51328)

      MediaShield UV HeatSet (also referred to as a heat-assist) overlaminating films are often described as a hybrid between thermal and pressure sensitive films. MediaShield films bond well to inkjet output with high ink coverage - even on photo gloss paper and digital photo laser output (Lambda / Lightjet). The image can be trimmed flush, or even die-cut without fear of delamination. Due to its quick setup / curing time, MediaShield laminated graphics can be handled or rolled immediately after processing. Unlike most heat-activated films, MediaShield overlaminating films are protected by a release liner because the adhesive on these films is slightly tacky when cool. Tips For Applying MediaShield UV Heatset Films: MediaShield UV Heatset films are an excellent choice for laminating multiple images which have been mounted onto a single board or substrate because they minimize air entrapment around the edges of each image. To keep the film from stretching as it becomes soft and pliable when heated, apply only minimal brake tension to the unwind supply shaft and the release liner take-up. Mediashield and thermal overlaminating films can be combined when encapsulating a graphic. For example: MediaShield Emerytex on the front and MHL White Backing on the back of the image is an ideal combination for trade show applications. Adjust the take up shaft so that the release liner is removed just prior to entering the nip rollers. By reducing the adhesive's exposure to the air, there is less chance of picking up dust particles.
    Part #: SX51328

    $662.38

  29. Drytac MediaShield Heatset Satinex UV 3mil 38" x 164' Overlaminate (SX38164)

      MediaShield UV HeatSet (also referred to as a heat-assist) overlaminating films are often described as a hybrid between thermal and pressure sensitive films. MediaShield films bond well to inkjet output with high ink coverage - even on photo gloss paper and digital photo laser output (Lambda / Lightjet). The image can be trimmed flush, or even die-cut without fear of delamination. Due to its quick setup / curing time, MediaShield laminated graphics can be handled or rolled immediately after processing. Unlike most heat-activated films, MediaShield overlaminating films are protected by a release liner because the adhesive on these films is slightly tacky when cool. Tips For Applying MediaShield UV Heatset Films: MediaShield UV Heatset films are an excellent choice for laminating multiple images which have been mounted onto a single board or substrate because they minimize air entrapment around the edges of each image. To keep the film from stretching as it becomes soft and pliable when heated, apply only minimal brake tension to the unwind supply shaft and the release liner take-up. Mediashield and thermal overlaminating films can be combined when encapsulating a graphic. For example: MediaShield Emerytex on the front and MHL White Backing on the back of the image is an ideal combination for trade show applications. Adjust the take up shaft so that the release liner is removed just prior to entering the nip rollers. By reducing the adhesive's exposure to the air, there is less chance of picking up dust particles.
    Part #: SX38164

    $346.05

  30. Drytac MediaShield Heatset Emerytex UV 5mil 51" x 328' Overlaminate (ET51328)

      MediaShield UV HeatSet (also referred to as a heat-assist) overlaminating films are often described as a hybrid between thermal and pressure sensitive films. MediaShield films bond well to inkjet output with high ink coverage - even on photo gloss paper and digital photo laser output (Lambda / Lightjet). The image can be trimmed flush, or even die-cut without fear of delamination. Due to its quick setup / curing time, MediaShield laminated graphics can be handled or rolled immediately after processing. Unlike most heat-activated films, MediaShield overlaminating films are protected by a release liner because the adhesive on these films is slightly tacky when cool. Tips For Applying MediaShield UV Heatset Films: MediaShield UV Heatset films are an excellent choice for laminating multiple images which have been mounted onto a single board or substrate because they minimize air entrapment around the edges of each image. To keep the film from stretching as it becomes soft and pliable when heated, apply only minimal brake tension to the unwind supply shaft and the release liner take-up. Mediashield and thermal overlaminating films can be combined when encapsulating a graphic. For example: MediaShield Emerytex on the front and MHL White Backing on the back of the image is an ideal combination for trade show applications. Adjust the take up shaft so that the release liner is removed just prior to entering the nip rollers. By reducing the adhesive's exposure to the air, there is less chance of picking up dust particles.
    Part #: ET51328

    $875.70

Items 1-15 of 22

Display Type List Grid
Page:   1   10   20   30   35   36   37   38   39   40   41   42   43   44   45   46   47   48   49   50   51   52   53   54   55   56   57   58   59   60   61   62   63   64   70   80