Need Help 1-800-944-4573 1-800-944-4573

Drytac Laminating Equipment

  1. Drytac ML25 Manual Hand Crank Pressure Sensitive Cold Mount Roll Laminator

    Part number: DTML25

    • Max Laminating Width: 25.5 inches (648mm)
    • Width: 27.375 inches (695.3mm)
    • Depth: 24.5 inches (622mm)
    • Height: 10.25 inches (260mm)

    Your Price: $348.99

  2. Drytac JetMounter JM18 Electric 18 Inch Pressure Sensitive Cold Mount Laminator - Roll Laminators

    Part number: DTJM18

    • Max Laminating Width: 18.25 inches (464mm)
    • Width: 25.5 inches (648mm)
    • Depth: 11.75 inches (299mm)
    • Height: 13 inches (330mm)

    Your Price: $780.95

  3. Drytac JetMounter JM26 Electric 26 Inch Pressure Sensitive Cold Mount Laminator - Roll Laminators

    Part number: DTJM26

    • Max Laminating Width: 26.25 inches (667mm)
    • Width: 33.25 inches (845mm)
    • Depth: 12.2 inches (310mm)
    • Height: 12.3 inches (312.5mm)

    List Price: $995.00

    Your Price: $994.00

    You Save: 0%

  4. Drytac JetMounter Electric 34 Inch Pressure Sensitive Cold Mount Laminator - Roll Laminators

    Part number: JM34

    • Max Laminating Width: 34.25" (86.9 cm)
    • Max Board Thickness: .75" (1.9 cm)
    • Unpacked Weight: 70.5 lbs (32 kg)
    • Width: 41.33" (105 cm)

    Your Price: $1,498.95

  5. Drytac Push/Pull Hangers

    Part number: ACC9700

    • Quantity: Package of 100
    • Part Number: ACC9700
    • Quantity: Package of 100
    • Capable to provide a quick and easy hanging solution in minutes

    Your Price: $71.94

  6. Drytac 12" Dust Removal System Roller - Laminating Accessories

    Part number: ACC9050

    • Size: 12"
    • Warning: Not suitable with Epson Printers
    • Part Number: ACC9050
    • Size: 12"

    Your Price: $215.63

  7. Drytac Dust Removal System Pads - 5 Pads

    Part number: PCRPAD-5

    • Qty: 5 Pads (50 Sheets/Pad)
    • Warning: Is not suitable with Epson Printers
    • Part Number: PCRPAD-5
    • Roller is not included

    Your Price: $240.00

  8. Drytac MHL Lustre UV 3mil 38" x 500' Low Temp Laminating Film - Low Melt

    Part number: MLD38503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $422.42

    Your Price: $295.69

    You Save: 30%

  9. Drytac MHL Lustre UV 3mil 43" x 500' Low Temp Laminating Film - Low Melt

    Part number: MLD43503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    Your Price: $334.60

  10. Drytac MHL Lustre UV 3mil 51" x 500' Low Temp Laminating Film - Low Melt

    Part number: MLD51503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $566.92

    Your Price: $396.84

    You Save: 30%

  11. Drytac MHL Matt UV 3mil 38" x 500' Low Temp Thermal Laminating Film - Low Melt

    Part number: MM38503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $420.56

    Your Price: $294.39

    You Save: 30%

  12. Drytac MHL Matt UV 3mil 43" x 500' Low Temp Thermal Laminating Film - Low Melt

    Part number: MM43503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $475.92

    Your Price: $333.14

    You Save: 30%

  13. Drytac MHL Matt UV 3mil 51" x 500' Low Temp Thermal Laminating Film - Low Melt

    Part number: MM51503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $564.48

    Your Price: $395.14

    You Save: 29%

  14. Drytac MHL Matt UV 3mil 61" x 500' Low Temp Thermal Laminating Film - Low Melt

    Part number: MM61503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    Your Price: $472.60

  15. Drytac MHL Gloss 3mil 25" x 500' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD25503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $215.74

    Your Price: $151.02

    You Save: 29%

  16. Drytac MHL Gloss 3mil 38" x 500' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD38503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $327.92

    Your Price: $229.54

    You Save: 30%

  17. Drytac MHL Gloss 3mil 43" x 500' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD43503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $371.02

    Your Price: $259.71

    You Save: 30%

  18. Drytac MHL Gloss 3mil 51" x 500' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD51503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $440.10

    Your Price: $308.07

    You Save: 30%

  19. Drytac MHL Gloss 5mil 25" x 250' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD25205

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $209.76

    Your Price: $146.83

    You Save: 30%

  20. Drytac MHL Gloss 5mil 38" x 250' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD38205

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $318.82

    Your Price: $223.17

    You Save: 30%

  21. Drytac MHL Gloss 5mil 43" x 250' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD43205

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $360.78

    Your Price: $252.55

    You Save: 29%

  22. Drytac MHL Gloss 5mil 51" x 250' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD51205

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $427.90

    Your Price: $299.53

    You Save: 30%

  23. Drytac MHL Gloss 5mil 55" x 250' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD55205

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $461.46

    Your Price: $329.49

    You Save: 28%

  24. Drytac MHL Gloss 10mil 25" x 250' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD25210

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $500.22

    Your Price: $350.15

    You Save: 30%

  25. Drytac MHL Gloss 10mil 38" x 250' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD38210

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $760.30

    Your Price: $532.21

    You Save: 30%

  26. Drytac MHL Gloss 10mil 43" x 250' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD43210

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $860.36

    Your Price: $602.25

    You Save: 30%

  27. Drytac MHL Gloss 10mil 51" x 250' Low Temp Thermal Laminating Film - Low Melt

    Part number: MGD51210

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $1,020.38

    Your Price: $714.27

    You Save: 29%

  28. Drytac MHL Scribe 3mil 25" x 500' Dry Erase Laminating Film - Pressure Sensitive

    Part number: MS25503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $229.48

    Your Price: $163.89

    You Save: 28%

  29. Drytac MHL Scribe 3mil 38" x 500' Dry Erase Laminating Film - Pressure Sensitive

    Part number: MS38503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    Your Price: $244.20

  30. Drytac MHL Scribe 3mil 51" x 500' Dry Erase Laminating Film - Pressure Sensitive

    Part number: MS51503

    • MHL overlaminating films are specifically developed for multi-heat roller laminators (MHL) and hotshoe laminators. These high quality laminating / encapsulating films are co-extruded for a carefully balanced ratio of polyester film to adhesive. The result is higher clarity for more vibrant colors, reduced "orange peel", greater rigidity (which reduces wrinkles and waves) and better adhesive flow characteristics (wet out). MHL laminating films are Consider webbing your laminator with a gloss film on top and a luster film on the bottom supply shaft. This will allow you to change the surface finish by feeding in your image either face up or face down. Use your idler bar to increase the area of contact between the heated rollers and the film. To allow for proper heat recovery, laminators with smaller diameter rollers require a slower processing speed and / or higher operating temperature for the best results. MHL laminating films bond while they are cooling (thermoplastic). This means that it is important that you create a steady uniform tension with the pull rollers (and a cooling system for thicker films) to ensure a smooth, flat encapsulated print without waves or wrinkles.

    List Price: $468.16

    Your Price: $327.71

    You Save: 30%