Mactac Permacolor Overlaminates and Mounting Films

Page
  1. Mactac Permacolor ColorTrans Optically Clear 61" x 150' Perm/Rem Mounting Film (CT2261L150)

    • Physical Properties Property Typical Values Test Method Thickness in inches Carrier plus adhesive Total product 0.0037 (94) 0.0067 (170) ASTM D-645 Quick Tack lb. /in² (N/25mm) Stainless Steel Permanent Removable 2.8 (12.3) 2.5 (11) Mactac CTM-25 Peel Adhesion lb./in. (N/25 mm) Stainless Steel - 30 minutes Stainless Steel – 24 hours 4.0 (17.5) 1.2 (5.2) 5.2 (22.7) 1.6 (7.0) PSTC - 3 Shear, Hours to Fail Stainless Steel 100+ 24+ PSTC - 7 Temperature Ranges Application for best results: End Use: 50° to 120°F (10° - 49°C) -40° to 185°F (-40° to 85°C)
    • Shelf Life Two years when stored at 75°F (24°C) and 50% relative humidity or less. Note: Mactac recommends that rolls be stored on end or suspended from the core.
    • Removability This product has 6 month removability after application from glass, Plexiglas and acrylic sheeting. The removability of CT2500 may be affected by the following substrates: polystyrene, nitrocellulose painted surfaces and soft PVC. With such substrates an increase of adhesion over time may occur and adhesive residue on removal may be noticed.
    • Limitations 1) The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide. 2) If there are any questions about applications, please contact your Mactac sales representative to discuss your requirements for recommendations. 3) If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest, most up-to-date version.
    • General Comments
    Part #: CT2261L150

    $614.47

  2. Mactac Permacolor ColorTrans Optically Clear 51" x 150' Perm/Rem Mounting Film (CT2251L150)

    • Physical Properties Property Typical Values Test Method Thickness in inches Carrier plus adhesive Total product 0.0037 (94) 0.0067 (170) ASTM D-645 Quick Tack lb. /in² (N/25mm) Stainless Steel Permanent Removable 2.8 (12.3) 2.5 (11) Mactac CTM-25 Peel Adhesion lb./in. (N/25 mm) Stainless Steel - 30 minutes Stainless Steel – 24 hours 4.0 (17.5) 1.2 (5.2) 5.2 (22.7) 1.6 (7.0) PSTC - 3 Shear, Hours to Fail Stainless Steel 100+ 24+ PSTC - 7 Temperature Ranges Application for best results: End Use: 50° to 120°F (10° - 49°C) -40° to 185°F (-40° to 85°C)
    • Shelf Life Two years when stored at 75°F (24°C) and 50% relative humidity or less. Note: Mactac recommends that rolls be stored on end or suspended from the core.
    • Removability This product has 6 month removability after application from glass, Plexiglas and acrylic sheeting. The removability of CT2500 may be affected by the following substrates: polystyrene, nitrocellulose painted surfaces and soft PVC. With such substrates an increase of adhesion over time may occur and adhesive residue on removal may be noticed.
    • Limitations 1) The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide. 2) If there are any questions about applications, please contact your Mactac sales representative to discuss your requirements for recommendations. 3) If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest, most up-to-date version.
    • General Comments
    Part #: CT2251L150

    $513.76

  3. Mactac Permacolor ColorTrans CT2200 Series Optically Clear Perm/Rem Mounting Films (MACTAC-CT22)

    • Physical Properties Property Typical Values Test Method Thickness in inches Carrier plus adhesive Total product 0.0037 (94) 0.0067 (170) ASTM D-645 Quick Tack lb. /in² (N/25mm) Stainless Steel Permanent Removable 2.8 (12.3) 2.5 (11) Mactac CTM-25 Peel Adhesion lb./in. (N/25 mm) Stainless Steel - 30 minutes Stainless Steel – 24 hours 4.0 (17.5) 1.2 (5.2) 5.2 (22.7) 1.6 (7.0) PSTC - 3 Shear, Hours to Fail Stainless Steel 100+ 24+ PSTC - 7 Temperature Ranges Application for best results: End Use: 50° to 120°F (10° - 49°C) -40° to 185°F (-40° to 85°C)
    • Shelf Life Two years when stored at 75°F (24°C) and 50% relative humidity or less. Note: Mactac recommends that rolls be stored on end or suspended from the core.
    • Removability This product has 6 month removability after application from glass, Plexiglas and acrylic sheeting. The removability of CT2500 may be affected by the following substrates: polystyrene, nitrocellulose painted surfaces and soft PVC. With such substrates an increase of adhesion over time may occur and adhesive residue on removal may be noticed.
    • Limitations 1) The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide. 2) If there are any questions about applications, please contact your Mactac sales representative to discuss your requirements for recommendations. 3) If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest, most up-to-date version.
    • General Comments
    Part #: MACTAC-CT22

    $513.76

  4. Mactac Permacolor PermaPrint White 54" x 150' Perm/Perm Back Mounting Film (IP5040)

    • Features and Benefits:
    • One paper release liner allows for fast lamination
    • Typical Uses:
    • Mounting of images to black gator, Sintra and other typical mounting substrates
    • Physical Properties Property Typical Values Test Method Thickness mils (mm) Adhesive Carrier and Adhesive 1/1 (0.028/0.028) 4.5 (0.114) ASTM D-645 Peel Adhesion, lb. /in. (N/25 mm) Stainless Steel - 30 min. - 24 hr. 3.5 (19) 4.0 (22) PSTC - 3 Quick Tack lb. /in² (N/25mm) Stainless Steel 4.4 (17.5) MACtac CTM-25 Shear, Hours to Fail Stainless Steel 150 PSTC - 7 Temperature Ranges Application for best results: End Use: 50° to 120°F (10° - 49°C) -20° to 200°F (-30° to 93°C) Adhesive pH Neutral TAPPI-529
    Part #: IP5040

    $546.37

  5. Mactac Permacolor PermaPrint White 51" x 400' Perm/Perm Back Mounting Film (IP5001)

    • Features and Benefits:
    • One paper release liner allows for fast lamination
    • Typical Uses:
    • Mounting of images to black gator, Sintra and other typical mounting substrates
    • Physical Properties Property Typical Values Test Method Thickness mils (mm) Adhesive Carrier and Adhesive 1/1 (0.028/0.028) 4.5 (0.114) ASTM D-645 Peel Adhesion, lb. /in. (N/25 mm) Stainless Steel - 30 min. - 24 hr. 3.5 (19) 4.0 (22) PSTC - 3 Quick Tack lb. /in² (N/25mm) Stainless Steel 4.4 (17.5) MACtac CTM-25 Shear, Hours to Fail Stainless Steel 150 PSTC - 7 Temperature Ranges Application for best results: End Use: 50° to 120°F (10° - 49°C) -20° to 200°F (-30° to 93°C) Adhesive pH Neutral TAPPI-529
    Part #: IP5001

    $1045.59

  6. Mactac Permacolor PermaPrint White 51" x 150' Perm/Perm Back Mounting Film (IP5002)

    • Features and Benefits:
    • One paper release liner allows for fast lamination
    • Typical Uses:
    • Mounting of images to black gator, Sintra and other typical mounting substrates
    • Physical Properties Property Typical Values Test Method Thickness mils (mm) Adhesive Carrier and Adhesive 1/1 (0.028/0.028) 4.5 (0.114) ASTM D-645 Peel Adhesion, lb. /in. (N/25 mm) Stainless Steel - 30 min. - 24 hr. 3.5 (19) 4.0 (22) PSTC - 3 Quick Tack lb. /in² (N/25mm) Stainless Steel 4.4 (17.5) MACtac CTM-25 Shear, Hours to Fail Stainless Steel 150 PSTC - 7 Temperature Ranges Application for best results: End Use: 50° to 120°F (10° - 49°C) -20° to 200°F (-30° to 93°C) Adhesive pH Neutral TAPPI-529
    Part #: IP5002

    $428.61

  7. Mactac Permacolor PermaPrint White 38" x 150' Perm/Perm Back Mounting Film (IP5008)

    • Features and Benefits:
    • One paper release liner allows for fast lamination
    • Typical Uses:
    • Mounting of images to black gator, Sintra and other typical mounting substrates
    • Physical Properties Property Typical Values Test Method Thickness mils (mm) Adhesive Carrier and Adhesive 1/1 (0.028/0.028) 4.5 (0.114) ASTM D-645 Peel Adhesion, lb. /in. (N/25 mm) Stainless Steel - 30 min. - 24 hr. 3.5 (19) 4.0 (22) PSTC - 3 Quick Tack lb. /in² (N/25mm) Stainless Steel 4.4 (17.5) MACtac CTM-25 Shear, Hours to Fail Stainless Steel 150 PSTC - 7 Temperature Ranges Application for best results: End Use: 50° to 120°F (10° - 49°C) -20° to 200°F (-30° to 93°C) Adhesive pH Neutral TAPPI-529
    Part #: IP5008

    $315.57

  8. Mactac Permacolor PermaPrint White 37" x 150' Perm/Perm Back Mounting Film (IP5007)

    • Features and Benefits:
    • One paper release liner allows for fast lamination
    • Typical Uses:
    • Mounting of images to black gator, Sintra and other typical mounting substrates
    • Physical Properties Property Typical Values Test Method Thickness mils (mm) Adhesive Carrier and Adhesive 1/1 (0.028/0.028) 4.5 (0.114) ASTM D-645 Peel Adhesion, lb. /in. (N/25 mm) Stainless Steel - 30 min. - 24 hr. 3.5 (19) 4.0 (22) PSTC - 3 Quick Tack lb. /in² (N/25mm) Stainless Steel 4.4 (17.5) MACtac CTM-25 Shear, Hours to Fail Stainless Steel 150 PSTC - 7 Temperature Ranges Application for best results: End Use: 50° to 120°F (10° - 49°C) -20° to 200°F (-30° to 93°C) Adhesive pH Neutral TAPPI-529
    Part #: IP5007

    $322.64

  9. Mactac Permacolor PermaPrint White 25" x 150' Perm/Perm Back Mounting Film (IP5015)

    • Features and Benefits:
    • One paper release liner allows for fast lamination
    • Typical Uses:
    • Mounting of images to black gator, Sintra and other typical mounting substrates
    • Physical Properties Property Typical Values Test Method Thickness mils (mm) Adhesive Carrier and Adhesive 1/1 (0.028/0.028) 4.5 (0.114) ASTM D-645 Peel Adhesion, lb. /in. (N/25 mm) Stainless Steel - 30 min. - 24 hr. 3.5 (19) 4.0 (22) PSTC - 3 Quick Tack lb. /in² (N/25mm) Stainless Steel 4.4 (17.5) MACtac CTM-25 Shear, Hours to Fail Stainless Steel 150 PSTC - 7 Temperature Ranges Application for best results: End Use: 50° to 120°F (10° - 49°C) -20° to 200°F (-30° to 93°C) Adhesive pH Neutral TAPPI-529
    Part #: IP5015

    $219.03

  10. Mactac Permacolor PermaPrint IP5000 Series White Perm/Perm Back Mounting Films (MACTAC-IP5000)

    • Features and Benefits:
    • One paper release liner allows for fast lamination
    • Typical Uses:
    • Mounting of images to black gator, Sintra and other typical mounting substrates
    • Physical Properties Property Typical Values Test Method Thickness mils (mm) Adhesive Carrier and Adhesive 1/1 (0.028/0.028) 4.5 (0.114) ASTM D-645 Peel Adhesion, lb. /in. (N/25 mm) Stainless Steel - 30 min. - 24 hr. 3.5 (19) 4.0 (22) PSTC - 3 Quick Tack lb. /in² (N/25mm) Stainless Steel 4.4 (17.5) MACtac CTM-25 Shear, Hours to Fail Stainless Steel 150 PSTC - 7 Temperature Ranges Application for best results: End Use: 50° to 120°F (10° - 49°C) -20° to 200°F (-30° to 93°C) Adhesive pH Neutral TAPPI-529
    Part #: MACTAC-IP5000

    $219.03

  11. Mactac Permacolor Gemini XT 51" x 400' Opaque White Rubber Back Mounting Film (PP5051L400)

    • Features and Benefits:
    • High-tack, high-peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: PP5051L400

    $613.87

  12. Mactac Permacolor Gemini XT 51" x 150' Opaque White Rubber Back Mounting Film (PP5051L150)

    • Features and Benefits:
    • High-tack, high-peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: PP5051L150

    $230.20

  13. Mactac Permacolor Gemini XT 54" x 400' Opaque White Rubber Back Mounting Film (PP5054L400)

    • Features and Benefits:
    • High-tack, high-peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: PP5054L400

    $649.97

  14. Mactac Permacolor Gemini XT 54" x 150' Opaque White Rubber Back Mounting Film (PP5054L150)

    • Features and Benefits:
    • High-tack, high-peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: PP5054L150

    $244.14

  15. Mactac Permacolor Gemini XT 61" x 150' Opaque White Rubber Back Mounting Film (PP5061L150)

    • Features and Benefits:
    • High-tack, high-peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: PP5061L150

    $264.54

  16. Mactac Permacolor Gemini XT Opaque White Rubber Back Mounting Films (MACTAC-PP5000)

    • Features and Benefits:
    • High-tack, high-peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: MACTAC-PP5000

    $230.20

  17. Mactac Permacolor Gemini XT 51" x 400' Clear Rubber Back Mounting Film (PP5651L400)

    • Features and Benefits:
    • High-tack, high peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: PP5651L400

    $526.87

  18. Mactac Permacolor Gemini XT 51" x 150' Clear Rubber Back Mounting Film (PP5651L150)

    • Features and Benefits:
    • High-tack, high peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: PP5651L150

    $197.57

  19. Mactac Permacolor Gemini XT 54" x 400' Clear Rubber Back Mounting Film (PP5654L400)

    • Features and Benefits:
    • High-tack, high peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: PP5654L400

    $557.87

  20. Mactac Permacolor Gemini XT 54" x 150' Clear Rubber Back Mounting Film (PP5654L150)

    • Features and Benefits:
    • High-tack, high peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: PP5654L150

    $209.06

  21. Mactac Permacolor Gemini XT Clear Rubber Back Mounting Films (MACTAC-PP5600)

    • Features and Benefits:
    • High-tack, high peel adhesions and high cohesive strength for quick adhesion
    • Good for low energy surfaces such as Sintra, plastic and styrene
    • Typical Uses:
    • General purpose mounting of digital images
    Part #: MACTAC-PP5600

    $197.57

  22. Mactac Permacolor RAYZor 1.5mil 60" x 150' Clear Matte Cast Vinyl Overlaminate (LF3639G)

    • Physical Properties Property Typical Values Test Method Thickness, inches (µm) Film plus adhesive Total product 0.0025 (64) 0.0039 (100) ASTM D-645 Peel Adhesion lb./in. (N/25mm) 180° on stainless steel -20 min - 24 hrs. 3.0 (13.1) 3.7 (16.5) PSTC-1 Quick Tack, lb./in² (N/25mm) Stainless Steel 2.5 (11) FTM - 9 Dimensional Stability, (%) 48 hours @ 158°F max 0.01 FTM - 14 10” x 10” Sample Bonded to aluminum Gloss (60°) 2 – 10 Temperature Ranges Minimum Application: End Use: 50°F (+10°C) -50°F to 225°F (-45°C to 107°C) Surface Burning Characteristics (Meets ANSI, NFPA, and IFC as class A) Flame Spread Smoke Density 0 30 ASTM E84-01 or ANSI/NFPA 255 or IFC 8-1 Adhesive pH Neutral TAPPI-529
    • Chemical Resistance Salt Water Spray .................... ASTM B 117-03
    • 100 hours @ 5% solution ........... no change Water Immersion
    • 100 hours immersed @ RT ........... no change Other immersion tests show:
    • Gasoline (30 min.) ........... No effect
    Part #: LF3639G

    $772.20

  23. Mactac Permacolor RAYZor 1.5mil 54" x 150' Clear Matte Cast Vinyl Overlaminate (LF3638G)

    • Physical Properties Property Typical Values Test Method Thickness, inches (µm) Film plus adhesive Total product 0.0025 (64) 0.0039 (100) ASTM D-645 Peel Adhesion lb./in. (N/25mm) 180° on stainless steel -20 min - 24 hrs. 3.0 (13.1) 3.7 (16.5) PSTC-1 Quick Tack, lb./in² (N/25mm) Stainless Steel 2.5 (11) FTM - 9 Dimensional Stability, (%) 48 hours @ 158°F max 0.01 FTM - 14 10” x 10” Sample Bonded to aluminum Gloss (60°) 2 – 10 Temperature Ranges Minimum Application: End Use: 50°F (+10°C) -50°F to 225°F (-45°C to 107°C) Surface Burning Characteristics (Meets ANSI, NFPA, and IFC as class A) Flame Spread Smoke Density 0 30 ASTM E84-01 or ANSI/NFPA 255 or IFC 8-1 Adhesive pH Neutral TAPPI-529
    • Chemical Resistance Salt Water Spray .................... ASTM B 117-03
    • 100 hours @ 5% solution ........... no change Water Immersion
    • 100 hours immersed @ RT ........... no change Other immersion tests show:
    • Gasoline (30 min.) ........... No effect
    Part #: LF3638G

    $687.96

  24. Mactac Permacolor Enhancers 2.5mil Clear 54" x 50' Brilliant Crystal Metallic Gloss Overlaminate (CY63980154)

    • Features and Benefits:
    • Five year outdoor durability
    • Two enhancers finishes
    • Typical Uses:
    • Overlaminate - flat, slightly curved applications
    Part #: CY63980154

    $303.57

  25. Mactac Permacolor Enhancers 3mil Clear 54" x 50' Silver Metallic Gloss Overlaminate (CY63980054)

    • Features and Benefits:
    • Five year outdoor durability
    • Two enhancers finishes
    • Typical Uses:
    • Overlaminate - flat, slightly curved applications
    Part #: CY63980054

    $303.57

  26. Mactac Permacolor 6300 Metallic Enhancers Clear Gloss Overlaminates (MACTAC-CY63980)

    • Features and Benefits:
    • Five year outdoor durability
    • Two enhancers finishes
    • Typical Uses:
    • Overlaminate - flat, slightly curved applications
    Part #: MACTAC-CY63980

    $303.57

  27. Mactac Permacolor PermaTrans 61" x 150' Optically Clear Mounting Film (PUV2161W61L150)

    • Features and Benefits:
    • Industry’s best clarity.
    • UV inhibitors reduce color fade.
    • Aggressive solvent acrylic adhesive.
    • Clear liners for inspection of product before lamination.
    Part #: PUV2161W61L150

    $1580.71

  28. Mactac Permacolor PermaTrans 51" x 265' Optically Clear Mounting Film (PUV2151W51L265)

    • Features and Benefits:
    • Industry’s best clarity.
    • UV inhibitors reduce color fade.
    • Aggressive solvent acrylic adhesive.
    • Clear liners for inspection of product before lamination.
    Part #: PUV2151W51L265

    $2020.89

  29. Mactac Permacolor PermaTrans 51" x 150' Optically Clear Mounting Film (PUV2151W51L150)

    • Features and Benefits:
    • Industry’s best clarity.
    • UV inhibitors reduce color fade.
    • Aggressive solvent acrylic adhesive.
    • Clear liners for inspection of product before lamination.
    Part #: PUV2151W51L150

    $1278.04

  30. Mactac Permacolor PermaTrans 41" x 150' Optically Clear Mounting Film (PUV2141W41L150)

    • Features and Benefits:
    • Industry’s best clarity.
    • UV inhibitors reduce color fade.
    • Aggressive solvent acrylic adhesive.
    • Clear liners for inspection of product before lamination.
    Part #: PUV2141W41L150

    $1081.96

Items 1-15 of 22

Display Type List Grid

Related Categories