IMAGin ROODLE 6mil Matte White Removable Wall Print Media

Product Details

• Features and Benefits:
  • ROODLE meets the flame spread and smoke density specifications for ANSI/NFPA – Class A and IBC – Class A
  • Thick face makes ROODLE easy to install, even without a laminate
  • Removable for up to two years from most well maintained substrates
  • Solvent, eco-solvent, latex, and UV wide-format, as well as for screen printing


• Typical Uses:
  • Wall murals.
  • Decals.
  • Point-of-purchase displays.


• Use with:
  • PERMACOLOR LUV Series
  • PERMACOLOR PromoGard PG7000 Series


• Physical Properties
  
  

  Property	Typical Values	Test Method
  Thickness, inches (µm) Film plus adhesive	0.007 (200)	ASTM D-645
  Quick Tacks, lb./in.² (N/25mm) Stainless Steel	2.1 (9.2)	MACtac CTM-25
  Peel Adhesion lb./in. (N/25mm) 180° on Stainless Steel - 24 hr.	2.1 (9.2)	ASTM D-903
  Dimensional Stability, inches (mm) 48 hours @ 158°F MD CD	0.40 0.20	MACtac CTM-21 (Method D) 10" x 10" Sample Bonded to aluminum
  Temperature Range Minimum application: End Use:	32°F (0°C)* -40°F to 180°F (-40°C to 82°C)
  Surface Burning Characteristics (Meets ANSI, NFPA, & IFC as class A) Flame Spread Smoke Density	20 120	ASTM E84-01 or ANSI/NFPA 255 or IFC 8-1

  • When applying ROODLE at temperatures below 50°F the semi-rigid vinyl face will become brittle. Therefore special care must be employed during installation to keep it from tearing.


• Durability
  The outdoor durability of the unprinted film is 4 years. ROODLE has up to 2 year removability after application. Overlamination of the inkjet-printed material with Permacolor® overlaminates delays color fading that may occur over time. This color fading is mainly dependent upon the inks quality (see technical data sheets given by the ink manufacturers) and the pressure sensitive media being used.


• Shelf Life
  2 years from Date of Manufacture when stored at 60/77°F (15/25°C) and 50% relative humidity in the original package


• Approved Printing Methods
  Screen Printing:             HP Indigo     No
  UV Cured     Yes     Off-set      No
  Solvent     Yes     UV Off-set       Yes
  WF Digital: UV Inkjet   Yes       Thermal Transfer     No
  Eco-solvent     Yes       Flexographic*    Yes
  True solvent     Yes       UV Flexographic     Yes
  Canon UVgel 356     Yes       Narrow Web UV Inkjet     Yes
  Latex     Yes            
  
  
  * Flexographic Printing requires a topcoat. WVG000113 and WVF010516 have been approved by ACTEGA Coatings and Sealants (ww.altana.com) as in-line coat-able ink primers.
  
  To achieve the best possible print quality, please make sure that the correct ICC profiles or printer settings are used. Profiles can be downloaded from www.mactac.com. Printer and heater settings and ICC profiles can also be downloaded from some O.E.M. or software manufacturer’s websites.
  
  The ICC profiles are provided solely as a customer resource. Print environments, the individual nature of printing systems, inks and software can significantly affect output. It is the customer’s responsibility to determine the suitability of any profile for use in their specific print environment.


• Limitations
  Due to the wide variability of interior walls, sealants and paints, no claims for successful applications or removal are made by MACtac. It is the users’ responsibility to determine the products suitability for the intended wall. The removability of WallNOODLE may be affected by the following substrates: polystyrene, nitrocellulose painted surfaces and soft vinyl. With such substrates an increase of adhesion over time may occur and may leave adhesive residue on removal.
  
  WallNOODLE is designed for smooth painted drywall poster applications and should not be used for full wall murals.
  
  
  • 1) The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide.
  • 2) If there are any questions about applications, please contact your Mactac sales representative to discuss your requirements for recommendations.
  • 3) If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest, most up-to-date version.


• Recommendations
  Always test your ROODLE media with your inks and laminating films prior to commercial use.
  
  • 1) Printing Conditions: Print in conditioned pressroom at ±73°F (23°C) and 50% RH. The maximum allowable ink saturation is 270%.
    • a) Images printed with solvent inks must be thoroughly dried prior to rolling for shipment. Retained solvent will affect edge adhesion.
  • 2) Laminating Conditions: If the printed graphic is likely to be exposed to corrosive liquids, smoke, fumes, and highly polluted areas or there is a likelihood of scratching, it is highly recommended to laminate with Permacolor ColorGard LUV Series (intermediate) or PromoGard (economy) overlaminating films.
  • 3) Transportation Conditions: To allow for easy transportation, IMAGin media can be rolled up, with the image out, with a minimum diameter of 6 inches (15cm). When the image is not protected by an overlaminate, make sure the print is completely dry and protected in a plastic bag. During transportation or storage, avoid exposing them to extreme temperature and humidity changes.
  • 4) Installation Instructions (Reference TA2500 for detailed drywall applications):
    • a. Before installing, unroll and lay flat. Allow the printed ROODLE to relax at room temperature for at least 90 minutes.
    • b. Do not allow the adhesive to touch any other areas of the product as this may result in damage to your ROODLE.
    • c. Do not install your ROODLE onto cold or damp surfaces, or anywhere near heaters, fires or central heating radiators.
    • d. If the wall has been freshly painted, allow it to fully cure, at least one week prior to installing your ROODLE. Consult your paint manufacturer for proper cure times.
    • e. Mactac recommends a test strip be included in the graphic for the end user to test on their walls. For best results insure the wall has a flat, smooth, even, dry surface. Avoid textured surfaces including textured paints, wallpapers, stucco, scrub-able paints, etc.
    • f. Make sure your ROODLE will fit in the area. Measure your wall and your ROODLE.
    • g. Use a clean alcohol saturated cloth to remove any dust from your wall surface. You may need a damp cloth or cleaners to remove excessive dirt and dust followed by the alcohol wipe. If so, allow an additional 24 hours to dry as many surfaces absorb moisture like a sponge!
    • h. Spread out your ROODLE on a flat surface, face down. Begin peeling back the liner off from the top down about 2 – 5 inches, and fold under. Position the ROODLE on the wall. Once it is in place, lightly tack down the exposed adhesive. Using a squeegee, smooth down the rest of the exposed adhesive working top down and from the center out. Remove 6 – 10” additional liner and apply with squeegee. Again working from the top down and from the center out.
    • i. Continue in this manner until the entire ROODLE has been applied.
    • j. For wall murals plan the graphic with a 1inch overlap.
    • k. Finish, by re-squeegeeing all the outer edges and overlapping seams to insure good contact with the wall surface
  • 5) Removal Instructions:
    • a. Starting in a corner, carefully pry up the vinyl from the wall.
    • b. Pull back at a 90° angle to create the least amount of stress on the painted surface underneath the graphic.
    • c. Continue peeling at a slow speed, keeping the angle 90° and diagonal to the panel.
    • d. For best results, remove slowly.


• • Values given are typical for unprocessed product and are not for use as specifications. Processing may change the values.

• Adhesive Type: Removable Acrylic
• Color: White
• Films: Vinyl (PVC)
• Finish: Matte
• Length: 100'
• Width: Choose Above
• Liner Category: 90# Superflat
• Outdoor Durability: 5 Years
• Precise Program: N
• Print Method: Latex, UV Inkjet
• Thickness: 6.0 mil