How to Remove the Back Cover from a Royal Sovereign Laminator?

posted this on Mar 29, 2016

Here is a transcript of this video:

In this video segment, we’re going to show how to remove the back cover from a Royal Sovereign Laminator. The first tool you’ll need is a Phillips screwdriver, either a manual screwdriver or a power screwdriver. We prefer a power screwdriver to speed up the process. First, we want to remove the screws off the side covers of the laminator. You’ll find one in the back, one possibly on the top, one in the front and one in the bottom of the front. Remove the cover. Proceed to the opposite side and remove that cover. Then we pull this out. We need to disconnect the emergency stop in the back and also our ribbon cable from our control panel. After removing the side cover, you want to check to see if there’s any screws on this side or the opposite side that holds the back cover on to the laminator. Now, to remove the back cover, you’ll find one to two screws that are facing you on the back, on the left and right side, and a series of screws, three or four, on the bottom. Remove those screws. Now, we’re going to raise and remove our back cover. Take off from the bottom and lift up and straight out, and your back cover will come off. You’ll be able to access your main drive motor, your circuit board and your transformer to the laminator.

Related Knowledgebase Articles
Can I bind documents longer than 11 inches with Comb Binding?
posted this on Mar 29, 2016

(Read More)

Can I use wire with my comb binding machine?
posted this on Mar 29, 2016

< Over the years, a number of customers have asked me whether they can use twin loop wire with their plastic comb binding machine. These customers often don’t want to have to buy a brand new machine but like the look and feel of twin loop wire binding. However, the answer to their question isn’t as simple as it seems. You see, they actually do make twin loop wire that is designed to work with the plastic comb binding hole pattern. With that said, if you want to use these wires you are going to need a way to close the wires. What is Spiral-O Wire?Let me explain a little bit more…There is a product that we carry called Spiral-O Wire. This wire has 19 loops and is designed to work with the hole pattern from a plastic comb binding machine. Spiral-O Wire is sometimes called Wire Combs or Ibico Wire and was originally designed for use with some of the older Ibico binding machines. A number of the older Ibico plastic comb binding machines also included a twin loop wire closer on the front of them to allow users to use both plastic combs and wire. This 19 loop wire was designed for this purpose.What Equipment is Needed? As the Ibico brand has been phased out by GBC and all of the older Ibico plastic binding machines have been replaced with new models, they no longer have the twin loop wire closer on the front of them. This presents a problem in trying to use these spiral-o wires since you can’t use the wires without a way to close them.One of the only options left is to purchase a Twin Loop wire closer. However, since twin loop wire closers are not incredibly cheap this option usually only appeals to users who have larger electric plastic comb binding machines. Otherwise, it is often advisable to simply buy a low end 3:1 pitch twin loop wire binding machine (the supplies are cheaper). This being said, if you have one of the older Ibico binding machines that has a wire closer included you are in luck. The Spiral-O binding supplies that we carry will work perfectly with your machine and you will be able to use both plastic combs and wire depending on your needs. These Spiral-O binding supplies are available in Black, Silver, White, Blue and Red and in sizes up to 1″ in diameter.If you aren’t sure what type of wire binding supplies that you need to work with your machine simply give us a call. Our trained sales representatives will be glad to help you find the correct supplies for use with your machine.(Read More)

How to clean my roll laminator?
posted this on Mar 29, 2016

(Read More)

How can I change the film on my roll laminator?
posted this on Mar 29, 2016

(Read More)

How to fix a jam on my pouch laminator?
posted this on Mar 29, 2016

(Read More)

What should I look for in a Laminator?
posted this on Mar 29, 2016

(Read More)

How do I use a carrier with my Pouch Laminator?
posted this on Mar 29, 2016

(Read More)

How should I use my pouch laminator?
posted this on Mar 29, 2016

(Read More)

How do I choose the right Laminating Pouch?
posted this on Mar 29, 2016

(Read More)

How do I laminate something with a Roll Laminator?
posted this on Mar 29, 2016

(Read More)