How to Install and Mount a Ghent Whiteboard?

If you are looking for whiteboard installation instructions or help mounting and installing your whiteboard or dry erase markerboard you have come the the right place.  This video will show you how to mount a Ghent whiteboard in three easy steps.  It really isn't as hard as you might think.  Although this video is provided by Ghent and shows how to mount one of their boards the same basic principles apply to boards from other manufacturers such as Balt/Best-Rite and Quartet.  You can even use these instructions to mount a bulletin board, chalkboard or tackboard.   Watch the video and if you still have questions please feel free to give us a call at 1-800-944-4573 or send us an email at sales@mybinding.com


Here is an audio transcript of this video:

Installing Ghent Marker Boards just got easier. Our new detach tray design helps lower labor costs by requiring fewer people needed for installation. Now installing is as easy as one, two, three.

Determine and mark a line at the desired height from the floor onto the wall. Place bottom edge of tray on the line and use the groove on the rear to guide as you drill holes through the tray. Secure the piece to the wall with the screws. Slide the marker board onto the tray. Then mark a line along the top edge of the marker board.

After removing the board, position the top edge of the L hangers along this line. Screw in the centre of each hanger slot and snuggly fasten. After replacing the board back onto the tray, tap the L hangers down until on top of the frame.

Using the L hangers as a template, mark the hole locations for the top screws and remove the board. Now drill holes into the top of the frame at each marked location. After replacing the back onto the tray, attach the marker board to the wall with screws provided. Installation is now complete.

Related Knowledgebase Articles
Can I bind documents longer than 11 inches with Comb Binding?
posted this on Mar 21, 2016

(Read More)

Can I use wire with my comb binding machine?
Krish Technologies posted this on Mar 21, 2016

< Over the years, a number of customers have asked me whether they can use twin loop wire with their plastic comb binding machine. These customers often don’t want to have to buy a brand new machine but like the look and feel of twin loop wire binding. However, the answer to their question isn’t as simple as it seems. You see, they actually do make twin loop wire that is designed to work with the plastic comb binding hole pattern. With that said, if you want to use these wires you are going to need a way to close the wires. What is Spiral-O Wire?Let me explain a little bit more…There is a product that we carry called Spiral-O Wire. This wire has 19 loops and is designed to work with the hole pattern from a plastic comb binding machine. Spiral-O Wire is sometimes called Wire Combs or Ibico Wire and was originally designed for use with some of the older Ibico binding machines. A number of the older Ibico plastic comb binding machines also included a twin loop wire closer on the front of them to allow users to use both plastic combs and wire. This 19 loop wire was designed for this purpose.What Equipment is Needed? As the Ibico brand has been phased out by GBC and all of the older Ibico plastic binding machines have been replaced with new models, they no longer have the twin loop wire closer on the front of them. This presents a problem in trying to use these spiral-o wires since you can’t use the wires without a way to close them.One of the only options left is to purchase a Twin Loop wire closer. However, since twin loop wire closers are not incredibly cheap this option usually only appeals to users who have larger electric plastic comb binding machines. Otherwise, it is often advisable to simply buy a low end 3:1 pitch twin loop wire binding machine (the supplies are cheaper). This being said, if you have one of the older Ibico binding machines that has a wire closer included you are in luck. The Spiral-O binding supplies that we carry will work perfectly with your machine and you will be able to use both plastic combs and wire depending on your needs. These Spiral-O binding supplies are available in Black, Silver, White, Blue and Red and in sizes up to 1″ in diameter.If you aren’t sure what type of wire binding supplies that you need to work with your machine simply give us a call. Our trained sales representatives will be glad to help you find the correct supplies for use with your machine.(Read More)

How to clean my roll laminator?
posted this on Mar 21, 2016

(Read More)

How can I change the film on my roll laminator?
posted this on Mar 21, 2016

(Read More)

How to fix a jam on my pouch laminator?
posted this on Mar 21, 2016

(Read More)

What should I look for in a Laminator?
posted this on Mar 21, 2016

(Read More)

How do I use a carrier with my Pouch Laminator?
posted this on Mar 21, 2016

(Read More)

How should I use my pouch laminator?
posted this on Mar 21, 2016

(Read More)

How do I choose the right Laminating Pouch?
posted this on Mar 21, 2016

(Read More)

How do I laminate something with a Roll Laminator?
posted this on Mar 21, 2016

(Read More)