Ledco H20 Heavy Duty 20" Hot Roll Laminator with Stand (Discontinued)

12186.67 NewCondition OutOfStock

We're sorry, but we no longer offer this item.

This item has been replaced with:

Tamerica TCC1200 Wide Format 45" Hot and Cold Roll Laminator

^$8,499.⁰⁰
- Lamination Thickness: 1.5 - 10 mil
- Lamination Speed: 4 fpm
- Mounting Capability: 3/16", 1/4", 1/2", 9/16"
- Max. laminating width: 45"
Learn More
Pro-Lam 38" Wide Format Heated Roll Laminator - PL-238WF

^$5,139.⁰⁰
- Ultra Duty Welded Steel Stand Standard
- Laminating Speed: 7' per Minute
- Max Film Thickness: 10 mil
- Hot or Cold: Both
Learn More
Tamerica Versalam-1300 13" One and Two-Sided Roll Laminator

^$3,058.⁰⁰
- Lamination Thickness: 1.5 - 10 mil
- Lamination Speed: 8.8 fpm
- Laminating Width: 13"
- Mounting Capability: up to 1/4"
Learn More
GBC Catena 105 40" Roll Laminator - 1715850

^$7,807.⁵⁹
- Max Laminate Width: 40"
- Laminating Speed: 5' per Minute
- Max Film Thickness: 10 mil
- Hot or Cold: Hot
Learn More

Ledco H20 Heavy Duty 20" Hot Roll Laminator with Stand (Discontinued)

Skip to the end of the images gallery

Skip to the beginning of the images gallery

SWIPE FOR MORE IMAGES

Product Description

This Ledco H20 Heavy Duty 20" Hot Roll Laminator laminates large graphics using films up to 10 mils thick, and up to 20 inches wide. This laminator operates at any speed up to 10 feet / 3 meters per minute. Thicker hot films are generally applied better at mid-range to lower speeds, while 1.5 mil hot films should be applied at mid-range to higher speeds. With H20 laminator, you can mount with hot or cold adhesives up to 1/2-inch thick, and can simultaneously mount and laminate.

Product Details

Variable speed. The laminator operates at any speed up to 10 feet / 3 meters per minute. Thicker hot films are generally applied better at mid-range to lower speeds, while 1.5 mil hot films should be applied at mid-range to higher speeds.
Attached safety shield. The polycarbonate shield is clear so operators can see their work. It does not conduct heat so they’ll be protected from hot areas. It is fixed to the laminator and the machine will not run if the feed tray and safety shield are not in place.
Lamination pressure. The rubber rollers are spring-loaded and preset to ensure correct and even lamination pressure. The pressure is easy to adjust if required when performing routine maintenance.
Ease of cleaning. The heated silicone rubber laminating rollers, and the silicone rubber pull rollers of the laminator should be cleaned regularly. The safety shield (see below) on the laminator swings away in seconds, making it easy to clean the laminating rollers.
Precision Heat Controls. Individual top and bottom heat controls, as used on our other Digital Laminators, allow for even, consistent heating of the laminating rollers throughout the entire temperature range.
Supply roll tension controls. Supply roll tension is easy to adjust by simply tightening or loosening the tension control knobs on the supply roll mandrels.
Feed tray pressure strip. This strip on the front of the feed tray holds images flat as they go into the laminator, making it easier to handle the lightweight papers sometimes used in digital imaging.
Ease of maintenance. The H20 laminator is made to last. However, some items on a laminator do wear out. Even the high-quality silicone rubber used in the rollers will lose flexibility over time. Extensive use may wear out the rollers, or an operator may cut a roller by accident. Rollers and other key parts can be changed quickly without disassembling the frame.