Permacolor 6300 Metallic Enhancers Clear Gloss Overlaminates

Product Details

• Features and Benefits:
  • Five year outdoor durability
  • Two enhancers finishes
• Typical Uses:
  • Overlaminate - flat, slightly curved applications
  • Vehicle, fleet and marine graphics
  • Colored vinyl enhancement
  • General signage
• Use with: B•free Gruv GVC929, B•free Gruv GV729, MACmark 6600, MACmark 9800 and Any graphic print for special effects finish
• Typical Applications
  

  Logos	Equipment identification
  Automotive applications	Container decals
  Fleet marking	General signage

• Physical Properties
  

  Property	Typical Values	Test Method
  Thickness, inches (µm) Film plus adhesive Crystal Silver	0.0037 (94) 0.0042 (107)	ASTM D-645
  Peel Adhesion 180° on Stainless Steel -20 min - 24 hrs.	2.8 (12.7) 4.0 (17.8)	ASTM D-903
  Face Material Data, 68°F (20°C) Tensile strength lb. /in. (N/m) Elongation %	>7.5 (1300) >120%	DIN 53455
  Dimensional Stability (shrinkage) in Percent	< 0.10	10" x 10" Sample Bonded on aluminum
  Temperature Ranges Application: End Use:	40° to 104°F (5° to 40°C) -50° to 225°F (-45° to 107°C)

• Shelf Life
  Two years when stored between at 60- 80°F (15 - 25°C) and 50% relative humidity or less.
• Durability
  This product is good for 5-year in outdoor durability. This use-life estimate is based upon accelerated age studies based on vertical applications under “normal” temperate climates. Please note that exposure to severe temperatures, ultra-violet light and also tropical, sub-tropical or desert regions will cause more rapid deterioration. This also applies to polluted areas, high altitude and south facing exposure.
• Chemical Resistance
  A sample is prepared in the same manner as for the Chemical Resistance Test and is immersed in the test fluid followed by drying at each stage.
  

  Test Fluid	Observation
  Gasoline (30min)	No Effect
  Distilled Water (24 hrs.)	No Effect
  SAE 20 Motor Oil (1 hr.)	No Effect
  10% HCL (10min)	No Effect
  10% NH4OH (10 min)	No Effect

• Limitations
  1) The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide.
  2) If there are any questions about applications, please contact your Mactac sales representative to discuss your requirements for recommendations.
  3) If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest, most up-to-date version.
  
• Recommendations
  1. Where exposure to moisture, chemicals, solvents or high pressure wash is anticipated, Mactac recommends sealing the edges with varnish, silicone or other sealant to prevent penetration by these liquids.
  2. Overlaminates should not be applied onto dusty or dirty prints.
  3. The mounting board must be properly prepared prior to mounting the image. This may include wiping with alcohol, light sanding or surface sealing depending on the board. Contact your board supplier for their recommendation.
  4. Mactac's pressure sensitive mounting films are intended for "Cold Roll Lamination" (40°F - 104°F). The addition of heat while simultaneous mounting with Thermal Overlaminates may result in curl or have other detrimental effects on the finished product.
  5. Whenever possible, always test first to ensure end-use capability.
  
• Application Tips
  Used as cut vinyl - Application of 6300 when used as cut-vinyl is made easier if Mactac prespacing tape is used, or can be applied as an overlaminating film with a standard laminator. Where exposures to chemical and solvent spills are likely to occur, edge sealing of decals with a varnish or clear coat will prevent edge lift. Correct varnishing of decals gives greater protection and longer end-use life against any prolonged effect of weathering, abrasion and other erosive effects such as frequent cleaning.
  
  Used as an Overlaminate for Vehicle Wraps - Because this is a much thicker overlaminate Mactac offers a limited warranty on flat to slightly curved surfaces. There is no warranty for Enhancers on motor vehicle wraps, over rivets and corrugations, through complex surfaces or for marine graphics.
• Values given are typical and are not necessarily for use in specification.

• Adhesive Type: Permanent Acrylic
• Color: Clear
• Films: Cast Vinyl (PVC)
• Finish: Crystal High Gloss
• Length: 50'
• Width: 54"
• Liner Category: 78# White Kraft
• Outdoor Durability: 5 Years
• Precise Program: N
• Thickness: Choose Above