Create an elegant and vibrant document with colorful graphics by fusing the foil to toner image areas with the Therm-O-Type FT-10 Foil Fuser. The FT-10 features a 12.6" wide maximum paper width entry, capable to produce an outstanding document that will stand out from the rest. Equipped with a single 500' foil round wound on a standard 1" core. With simple loading and reloading foil roll procedures, personalizing your own covers and documents became much easier. The foil fusing equipment ensures an efficient and productive process, without the need to purchase a foil stamping die or expensive foil stamping equipment. Don't just settle with the black and white print, spice up your presentation with the Therm-O-Type FT-10 Foil Fuser.
Product Details
Maximum Sheet Size: 12.6" Wide
Maximum Foil Roll Size: 500' long foil roll wound on a standard 1" core
Adjustable Speed:Yes
Adjustable Temperature: Yes
Core Size:1"
Compatible Foil Rolls: Metallic Foil,Holographic Foil and Gloss Pigment Foil
Foil Unwind/Rewind Tension Control:Yes
Jam Sensor:No
Power Requirements: 110V
Dimensions: 24" L x 16" W x 12" H
Weight: 44 lbs
Shipping Weight: 48 lbs
Manufacture's Manufacturer's Warranty:1 Year Limited Parts
Item Specifications
Actual Machine Dimensions: 19" X 13.5" X 8.5"
Actual Machine Weight : 45 LBS
Shipping Length : 24"
Shipping Width: 17"
Shipping Height: 13"
Shipping (Web) Weight: 50 lbs
Demonstration Video
Therm-O-Type Foil Fuser Demo Video
Transcript :
Attach the infeed tray. Make sure the main power is off. Forward/Off/Reverse should be Off. Impression lever in off position. Turn on main power. Set speed to 20%. Set temp. to 80%. Allow 15 min. to heat up. Loosen hubs on foil shaft. Remove foil support shaft. Install foil on support shaft. Be sure: Foil is oriented correctly, hub blades are engaged with foil roll, roll positioned correctly side to side. Do not overtighten screws. Pull about 15" from foil roll. Use card stock to push foil through fuser. Foil must be under stripper roller. Move switch to forward. Lower impres ...
Attach the infeed tray. Make sure the main power is off. Forward/Off/Reverse should be Off. Impression lever in off position. Turn on main power. Set speed to 20%. Set temp. to 80%. Allow 15 min. to heat up. Loosen hubs on foil shaft. Remove foil support shaft. Install foil on support shaft. Be sure: Foil is oriented correctly, hub blades are engaged with foil roll, roll positioned correctly side to side. Do not overtighten screws. Pull about 15" from foil roll. Use card stock to push foil through fuser. Foil must be under stripper roller. Move switch to forward. Lower impression lever. Allow foil to ?track" through fuser. Raise lever. If foil does not stop, increase tension here. Set paper side guide. Run a test sheet and check for quality. Thin papers require less heat at a given speed. Thick papers require more heat at a given speed. 80 lb. sample sheet being run. If tips of letters missing foil ? machine is going too slow or temperature too high. Incomplete foil transfer in solid areas ? running too fast or temperature too low. Check quality from lead edge to tail edge of sheet. Speed may need to be reduced to ensure quality across the sheet. To remove waste foil, cut foil & remove rewind shaft. Remove clamping bar, slide waste foil off shaft. Re-install the rewind shaft. Re-install the clamping bar.
The FT-10 goes from 0 to 300 degrees. If you run the machine at 300 degrees, it will ruin the rollers. When running the machine, you should have the temp. on the line between medium & high. 30% is the best speed to use.
Thank you for your question. The foil that you would use with the Therm-O-Type FT-10 Foil Fuser adheres to the toner from a laser printer. The type of stock would depend on the printer that you are working with. You will have the most success with a combination of printer ans stock that gets you even and compete coverage of your printed area.
Thank you for your question. Unfortunately Therm-O-Type does not provide a FPM rating for the FT-10 Foil Fuser because the speed it runs at would vary depending on the project. Thickness of stock and coverage of foil effects the speed that you are able to process your project. The Therm-O-Type FT-10 Foil Fuser has a variable speed control to adjust the speed to match the needs of the specific project.
Thank you for your question. We do not sell any used equipment. We do have some "open box" items that were either a demo model or a return. You can find our complete selection of clearance items here .
Answered by MyBinding
6 years and 11 months ago ago
Submit a New Question
Related Products
Navigating through the elements of the carousel is possible using the tab key. You can skip the carousel or go straight to carousel navigation using the skip links.
Press to skip carousel
