Permacolor PermaFlex Lustex IP6000 15mil Clear Rigid Overlaminates
0 0 0

Sorry, but Permacolor PermaFlex Lustex IP6000 15mil Clear Rigid Overlaminates is no longer available to buy.

We think you might like one of these instead:

Permacolor PermaFlex Lustex IP6000 15mil Clear Rigid Overlaminates

Brand: Mactac
  • Textured lustex finish polycarbonate
  • Eliminates glare
  • Three year outdoor / Five year indoor durability
  • Protects from abrasion and moisture
  • Ships Free Over $75
Starting At
Choose Product Below
  • 0
  • 1

Product Description

These Mactac Permacolor PermaFlex Lustex Clear Rigid Overlaminates are 15 mil film with a lustex textured, tough polycarbonate surface that is designed to add texture, rigidity, depth and slip resistance to your finished printed graphics. The low gloss texture helps eliminate glare, protection from abrasion, moisture and color fade from UV light. These films can be used as an overlaminate for indoor as well as outdoor applications. These Mactac Permacolor PermaFlex Lustex 15mil Clear Rigid Overlaminates are ideal for long and short term applications including trade shows, floor graphics and POP.

Product Details

  • Features and Benefits:
    • Textured lustex finish polycarbonate
    • Eliminates glare
    • Three year outdoor / Five year indoor durability
    • Protects from abrasion and moisture
    • Retards color fade caused by UV light

  • Typical Uses:
    • Trade show displays
    • Rollable graphics
    • Photo graphics
    • Counter mats
    • Direct food contact

  • Use with:StreetRAP, all REBEL and IMAGin print media

  • Physical Properties
    PropertyTypical ValuesTest Method
    Thickness, inches (µm)
    Film plus adhesive

    0.0165 (419)
    ASTM D-645
    Flame Resistance
    Flame Spread
    Smoke Developed
    ANSI, NFPA and IFC

    Class A
    ASTM E-84
    Static Coefficient of Friction
    (Slip Resistance)

    Dry floors = 0.5, Wet surfaces &
    Handicap accessible routes
    =0.6, Ramps =0.8
    Dry Neolite
    Wet Neolite

    ASTM C 1028
    SGS US Testing Co.
    White light Transmission 92%
    (Note: Glass = 100%)
    Mactac CTM-67
    Gloss (60° angle) 12 ASTM D-523
    Adhesive pH NeutralTAPPI –529
    Temperature Ranges
    Application for best results:
    End Use:

    Above 50°F (10°C)
    -20° to 200°F (-29° to 93°C)
    Direct Food ContactFDA conditions of Use
    B through H
    21 CFR 177.1580
    Subsections (a), (b) &(c)
    Co-efficient of Expansion1.7 X10-5in/in/°CASTM D696

  • Durability
    The durability of the film is 2-3 years in vertical (90±5°) applications outdoors and 3 -5 years indoors. While all Permacolor overlaminating films have UV resistance built in to help extend the life of your image, the durability of the image is mainly dependent upon the quality of the inks (see technical data sheets given by the ink manufacturers) and pressure sensitive media being used.

  • Shelf Life
    Two years when stored at 75°F (24°C) and 50% relative humidity or less. Note: Mactac recommends that rolls be stored on end or suspended from the core.

  • Limitations
    1) The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide.
    2) If there are any questions about applications, please contact your Mactac sales representative to discuss your requirements for recommendations.
    3) If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest, most up-to-date version.

  • Recommendations for Rolling and Shipping Laminated Images
    • Mactac studies and field surveys with numerous customers using Permacolor laminates in rolled-up graphic applications, leads to the following recommendations for rolling and shipping laminated images:
    • 1. Prior to rolling graphics:
      • a) A 2 - 4 hour wet-out period is strongly recommended for the adhesive system to build to ultimate adhesion. This will significantly improve your success with rolled-up graphics.
    • 2. For single-side laminated images:
      • a) Roll laminated side in for shipping and storage.
      • b) An inside roll diameter of 3 - 5 inches, minimum, is recommended for graphics with less than 10 mil total graphic thickness (includes imaged media and Permacolor overlaminates).
      • c) For images with a total thickness of 10 mils or greater an inside roll diameter of 10 - 12 inches, minimum, is recommended.
    • 3. For images laminated on both front and back sides:
      • a) Roll images with the thicker laminate to the outside for shipping and storage. For example: if your image has 5 or 10 mil Polycarbonate on the front and 15 mil Polycarbonate on the back (for additional stiffness), roll the graphic with the 15 mil PermaFlex side out.
      • b) All double laminated images should be rolled with an inside roll diameter of 10 - 12 inches minimum. Remember that a larger inside diameter is better.
    • Please keep in mind that this is a recommendation, individual experience should not be discounted. We recognize that different laminators and laminating methods may produce different results. The recommendations above represent our experience as having the “greatest” success in the field.
    • Values given are typical and are not necessarily for use in specification.

Product Reviews

Write Your Own Review
You're reviewing:Permacolor PermaFlex Lustex IP6000 15mil Clear Rigid Overlaminates
Your Rating

Item Specifications

  • Adhesive Type: Permanent Acrylic
  • Color: Clear
  • Films: Polycarbonate (PC)
  • Length: 150'
  • Width: Choose Above
  • Liner Category: 1.4 mil Polyester (PET)
  • Outdoor Durability: 3 Years
  • Precise Program: N
  • Thickness: 15 mil

Questions & Answers

Submit a New Question