ASSEMBLY INSTRUCTIONS

Fletcher F-3000 (60) / F3100 Stand

(Shown with machine mounted)

FORM #05-15-09

TABLE OF CONTENTS

TITLE

PAGE

Product Warranty .................................................................................................. 2

Parts Identification ................................................................................................ 3

Assembly:

1. Assemble Leg Tops to Top Mounting Bracket .......................................... 4
2. Assemble Left & Right Leg Bottoms to Leg Tops ..................................... 4
3. Assemble Rear Leg Bottom & Front/Back Horizontal Support Bars ............ 5
4. Assemble Front/Back Support Bar Bracket to Front/Back Horizontal Support Bars. ...................................................... 5
5. Assemble Front Horizontal Bar to Left & Right Legs and to the Front/Back Horizontal Support Bracket. ............................................ 6
6. Install Rubber Leg End Caps ................................................................. 6
7. Assemble the Adjustable Foot onto the Front Leg and attach the Front Leg onto your machine ................................................. 7
8. Assemble Front Horizontal Bar Brackets onto back of your machine .......... 7
9. Install your machine onto the assembled stand ........................................ 8

Detailed Parts List ................................................................................................. 9

Product Warranty

The Fletcher-Terry Company warrants the product purchased to be free from defects in parts and workmanship for

1. one year from the date of purchase. The Fletcher-Terry Company warrants that it will repair or replace any such defective parts, providing the product has been under normal use and service and the defective part is returned to The Fletcher-Terry Company at the purchaser’s expense. The Fletcher-Terry Company must authorize the return in writing. Proof of purchase must be submitted to validate warranty coverage. The warranty is in lieu of all other agreements and warranties expressed or implied. THE FLETCHER-TERRY COMPANY DOES HEREBY EXPRESSLY DISCLAIM ANY WARRANTIES OF MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The Fletcher-Terry Company does not authorize any company employee or representative to assume for it any other liability than that set forth in this Product Warranty. The Fletcher-Terry Company shall not be liable for any damages or losses, whether incidental or consequential or direct or indirect, arising out of the use or abuse of this product. This Warranty is valid only when product is used with Fletcher consumables and/or replacement parts. In any event, THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS OR ANY OTHER WARRANTY IS LIMITED TO RETURN OF THE PURCHASE PRICE PAID FOR THIS PRODUCT.

Parts Identification

Frame Components

Note: Some items may be pre-assembled.

Brackets & Hardware

Front/Back Support Bar Bracket

Front Horizontal Bar Bracket (x2)

Leg End Cap (x3)

Stand Assembly

Step #1:

Top Mounting Bracket

• Assemble Left, Right, & Rear Leg Tops to Top Mounting Bracket.
• Hardware: M8 x 50mm Screw (x3), M8 Flat Washer (x6), M8 Lock Nut (x3)

Step #2:

• Assemble Left and Right Leg Bottoms to Right and Left Leg Tops.
• Hardware: M8 x 50mm Screw (x4), M8 Flat Washer (x8), M8 Lock Nut (x4)

Stand Assembly

Step #3:

Front/Back Horizontal Support Bars

• Assemble Rear Leg Bottom to Top.
• Hardware: M8 x 50mm Screw (x2), M8 Flat Washer (x4), M8 Lock Nut (x2)
• Assemble Front/Back Horizontal Supports to Rear Leg.
• Hardware: M8 x 110mm Screw (x1), M8 Flat Washer (x2), M8 Lock Nut (x1)

Step #4:

• Assemble Front/Back Support Bracket to Front/Back Horizontal Support Bars.
• Hardware: M8 x 50mm Screw (x2), M8 Flat Washer (x4), M8 Lock Nut (x2)

Stand Assembly

Step #5:

Note: 4 holes this side

• Assemble Front Horizontal Bar to Left & Right Legs.
• Hardware: M8 x 80mm Screw (x2), M8 Flat Washer (x4), M8 Lock Nut (x2).
• Assemble Front Horizontal Bar to Front/Back Horizontal Support Bracket.
• Hardware: M8 x 50mm Screw (x2), M8 Flat Washer (x4), M8 Lock Nut (x2).

Step #6:

• Install a Rubber Leg End Cap to each leg bottom.

Stand Assembly

Step #7:

Vertical Extrusion

Adjustable Foot

• Assemble Adjustable Foot into bottom of the Front Leg.
• Assemble the Front Leg onto Vertical Extrusion at the back of your machine.
• Note which holes to use for your machine.
• Hardware: M6 x 70mm Screw (x2), M6 Flat Washer (x4), M6 Lock Nut (x2)

Step #8:

• Assemble the two Front Horizontal Bar Brackets onto the back underside of the Horizontal Extrusion on your machine.
• Hardware: M4 x 16mm Screw (x4), M4 Flat Washer (x4).

Stand Assembly

Step #9:

• Secure Brackets to top of Front Horizontal Bar
• Hardware: M8 x 50mm Screw (x4), M8 Flat Washer (x8), M8 Lock Nut (x4)
• Secure machine to Top Mounting Bracket
• Hardware: M6 x 35mm Screw (x2), M6 Flat Washer (x4), M6 Lock Nut (x2)

Turn Adjustable Foot to make contact with floor for proper machine support.

Parts List

View - A-

View - B-

View - D -

View - C -

View - E -

Description M6 Flat Washer M4 x 16mm Screw Adjustable Foot

Description M4 Flat Washer M6 x 35mm Screw M6 x 70mm Screw

M8 x 80mm Screw M8 x 50mm Screw

M8 x 110mm Screw M8 Flat Washer M8 Lock Nut

M6 Lock Nut Front/Back Horz. Support Bar Rear Leg Bottom Right Leg Top Front Horz Bar

Description Left Leg Bottom Top Mtg Bracket Front/Back Support Bar Bracket Front Horz Bar Bracket Left and Rear Leg Top

Right Leg Bottom Front Leg Leg End Cap