Page 1 of 3
Text on page 2
TECHNICAL INFORMATION
Punching Operation
Electric (Foot Pedal / Manual Switch)
Inserting Operation
Electric (Foot Pedal)
Electric Coil Punching and Inserting Binding Machine
OPERATIONAL MANUAL
Pitch
Hole Size
Round (4mm)
Disengageable Dies
Punching Length
Letter / A4
Punching Capacity
Up to 20 Sheets (20lb paper)
Binding Capacity
Up to 1" (Electric) / Up to 2" (Manual)
Weight & Volume
Warranty
INTRODUCTION
All 46
49 lbs & 1.9 CbFt
1 year
Congratulations on the purchase of your new , a professional electric coil punching and inserting binding machine. Your was designed with a full range of functions & safety features, along with premium quality components to guarantee an effortless and pleasant book binding experience, as well as many years of trouble-free service.
IMPORTANT
We recommend that you take a moment to familiarize yourself with the functions of your Make sure you read all the features and safety instructions, and follow these guidelines to install, operate and maintain your . You will find that with just a little practice, any person can achieve professional results.
F E AT URE S
WARRANTY POLICY
YOUR HAS A WARRANTY OF ONE YEAR FROM DATE OF PURCHASE. IN THE EVENT OF A MANUFACTURER’S DEFECT, YOUR DISTRIBUTOR (AT OPTION) WILL REPAIR OR REPLACE IT. IMPORTANT: THIS WARRANTY DOES NOT COVER DAMAGES DUE TO IMPROPER USE OR MISTREATMENT OF THE UNIT, INCLUDING ANY EXTRAORDINARY EVENT LEADING TO THE DAMAGE OF THE MACHINE, WHETHER IT IS REVERSIBLE OR NOT.
IF THE
IS NOT WORKING PROPERLY, FIRST FOLLOW THE CORRECTIVE ACTIONS ABOVE. IF THE PROBLEM PERSISTS, PLEASE CONTACT YOUR DEALER FOR FURTHER INSTRUCTIONS. PLEASE HAVE YOUR MACHINE’S SERIAL NUMBER AND THE PURCHASE DATE READY. IF THE MACHINE MUST BE RETURNED TO YOUR DISTRIBUTOR, IT IS YOUR RESPONSIBILITY TO PROPERLY PACK AND SHIP IT. AS ANY DAMAGES INCURRED DURING ITS TRANSPORTATION IS NOT COVERED BY OUR WARRANTY POLICY.
Function Control (Punch/Insert)
Manual Punch Switch
Depth Margin Control
Die Disengageable Pins
Issue Date: April 2013
Page 2 of 3
Text on page 3
ASSEMBLY & SAFETY INSTRUCTIONS
Place your new on top of a sturdy working table. Plug the power cord and foot pedal cord to the back of the machine. Turn on the Power Switch. Recommended: Switch the Function Control between PUNCH & INSERT and press foot pedal to test the electric punch and coil inserter. Keep fingers, hair, jewelry, necktie and any loose clothing or objects away from roller, as they may be accidentally pulled into the roller. Do not allow children to operate the machine. The is not a toy. Always turn switch-off and place foot pedal out of reach when machine is not in use. To reduce the risk of electric shock, never operate the near water. if power cord is damaged. Do not use the Do not allow the electric cord to be in contact with hot surfaces. In case of malfunction, return the unit to your distributor for service. This equipment does not contain any part that can be serviced by the consumer or operator.
- Use a test sheet to punch. If there are any holes running off the right and left edges of the punched paper, disengage the appropriate pins above .
- When punching PP or PVC, punch no more than 2 sheets at a time.
- Make sure to punch the front and back covers together to ensure an even binding.
- For maximum equipment durability, punch less than 15 sheets of 20lb paper at a time.
- Check and empty the Waste Drawer frequently. Overfilled Waste Drawer may damage the machine.
COIL INSERTING (BINDING)
Align punched document. Place document on top of machine or table and insert the coil into the first 4 to 5 holes from the right hand side. Make sure the Function Control is set on INSERT.
INSERT
PUNCH
Use the table below to determine the Coil Diameter to be used based on Sheet Capacity. Use the table below to determine the Depth Margin and turn the Depth Margin Control dial to the correct setting.
4.8mm 6.9mm 8.0mm 9.5mm 11mm 12.7mm 14.3mm 16mm 19mm 22mm 25.4mm
Note: The Depth Margin guide above is meant as a point of reference only. Some adjustment is needed to suit individual preference.
PUNCHING
Press Foot Pedal. The coil will automatically move forward inserting itself into the holes. After the coil is inserted completely to the document, IMMEDIATELY pull document away from the roller AND/OR let go of the foot pedal. REMARK: If coil is over-inserted, simply flip the document over and proceed with Step 3 again. Use the coil crimper to cut off excess coil and also crimp the ends to avoid document from unbinding.
Open Paper Entrance Cover. Place documents on the paper feeder. Adjust the Side Margin Guides to fit the paper size. Disengage any pins on either side of paper that would punch off the edge of the paper. Make sure the Function Control is set on PUNCH. Insert sheets and press Foot Pedal or Manual Punching Switch to punch.
INSERT
PUNCH
Upon completion of coil insertion, be sure to put the crimper back in the Coil Crimper Holder.
Issue Date: April 2013
Page 3 of 3 · End of manual
Quick start
- Set the machine on a sturdy table, plug in the power cord and foot pedal cord at the back, and turn on the power switch.
- Open the paper entrance cover, set the side margin guides to the paper size, and disengage any pins that would punch off the edge.
- Set Function Control to PUNCH, insert sheets and press the foot pedal or manual punch switch.
- Align the punched document and start the coil into the first 4–5 holes from the right side.
- Set Function Control to INSERT, set the Depth Margin dial for your coil size, and press the foot pedal to spin the coil in.
- Pull the document away or release the pedal as soon as the coil is fully inserted.
- Cut and crimp the coil ends with the coil crimper, then return it to its holder.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Holes run off the edges of the paper | Punch pins are engaged beyond the paper width | Disengage the appropriate pins, using a test sheet first. Also adjust the Side Margin Guides to fit the paper size. Page 3 |
| Punching plastic covers is difficult | Too many PP or PVC sheets at once | Punch no more than 2 sheets at a time, and punch the front and back covers together for an even binding. Page 3 |
| Machine strains when punching paper | Too many sheets at once | For maximum durability, punch less than 15 sheets of 20lb paper at a time. Capacity is up to 20 sheets. Page 3 |
| Machine may be damaged by waste | Overfilled Waste Drawer | Check and empty the Waste Drawer frequently. Page 3 |
| Coil is over-inserted | The coil went too far into the document | Flip the document over and proceed with the coil insertion step again. Pull the document away from the roller and let go of the foot pedal right after the coil is inserted. Page 3 |
| Machine does not punch or insert | Function Control is not set to the right mode | Set the Function Control to PUNCH or INSERT, and test with the foot pedal. If it still malfunctions, return the unit to your distributor for service. Page 3 |
Frequently asked questions
How many sheets can the AlphaCoil-E punch at once?
Up to 20 sheets of 20 lb paper. For maximum durability, punch fewer than 15 sheets at a time, and no more than 2 sheets of PP or PVC. See page 2 and page 3.
How thick a book can it bind?
Up to 1" with electric inserting, or up to 2" manually. See page 2.
What if the coil goes in too far?
Flip the document over and run the inserting step again. See page 3.
How do I avoid holes running off the edge of the paper?
Punch a test sheet and disengage the pins that punch off the left or right edge. See page 3.
What is the warranty?
One year from the date of purchase against manufacturer's defects. See page 2.
