Akiles Diamond 6 Operation Manual

Specifications

Item No. AD-6

Operational Manual

Radius 3/8" Four Kinds of Blades Straight length 5/8" Cutting Capacity 23.6" ( 600 sheets ) Cutting Speed 46 rpm Dimensions 24.6"(W) X 12.6"(D) X 17.5"(H) Weight / Volumn 103 Ibs / 3.14 CbFt Power 110vac (50~60Hz) Motor 100W

Item No: Ad-6

TABLE OF CONTENTS ITEM NO.: AD-6 ITEM NO.: AD-6

A. Name of machine parts ...

Specifications Q'ty Specifications Q'ty No.

Hardware description Hardware description

B. Safety instructions .. 03X12L 85 Location pins

C. All kinds of blade Location pins 05X12L ① Upper blades... Hex socket head screws M3X12L 89 2 Lower blade pads Hex socket head screws M4X8L

Hex socket head screws M4X12L

D. Standard parts & accessories

Location pins 03X12L

E. Optional parts & accessories

Location pins 05X12L

F. Machine operation Location pins 93 05X28L ① Installation and cutting test ... M4X28L 94 Hex socket head screws

Location pins 05X10L

Steel ball

a. Without calibrate gauge ....

Hex socket head screws

b. With calibrate gauge .... M3X8L

Location pins 03X10L

③ Changing blades

105 M4X10L Hex socket head screws

a. Changing the upper blade ...

106 Hex flat head screws

b. Changing the lower blade pad .

108 Hexflat head screws

C. Changing the blade base

Location pins 04X6L

d. Changing the straight blade C15 10 ④ How to use the "L" guide ·.

G. Maintenance ① Changing fuse and discharge capacitor . 11 ② Lubrication applying 11 ③ Blade sharpened .... 12

H. Electronic control system ① Electrical drawing.... 13 2 Position chart ..... 14 I. Diagram and parts list ①Machine main structure 2 Parts of structure: Main shaft system and Lower blade system .........· 17 ③Screws and other standard hardware parts list...

Item No.: Ad-6 Item No.: Ad-6

4Screws and other standard hardware parts list A. Name of machine parts No. No. Specifications Hardware description Q'ty Hardware description Specific at lons Q'ty Hex socket head screws M4X16L M3X10L 156 Hex flat head screws Washers 04X2t Hex button head screws

M4X8L M4X8L

Hex button head screws 157 Hex flat head screws Auto/Manual select button Power switch M4X6L 45 Hex flat head screws Hex socket head screws Emergency stop Reverse/Manualstartselectbutton M4X6L Hex flat head screws

Hex socket head screws M3X10L

Hex socket head screws Hex socket head screws M4X12L M4X6L 49 Hex socket head screws Hex flat head screws M4X8L 10 151 M4X6L Frontplate Hex socket head screws Hex socket head screws M4X12L M4X8L 50 Hex socket head screws

M4X8L 51 M4X12L

11 Hex sockethead screws Adjust button for

safety protector

Cross round head screws 12 54 M3X16L 08x2t 13 Hex socket head screws Hex flat head screws M4X6L 55 M4X8L Left side guide Hex flat head screws Hex socket head screws 57 M6X20L 14 M4X8L Washers 158 06X2t Hex socket head screws M8X25L Right side guide Hex nuts M6 Washers 08x2t

Lower blade pad Safety protector

16 M5X10L Hex nuts M8 Hex socket head screws Location pins 05x10L 59 Cross round head screws

M4X8L M4X10L

17 Cross round head screws Hex socket head screws 18 Hex socket head screws 61 Hex socket head screws M4X8L M4X8L

Standard work desk (12.6"X11.8")

Hex socket head screws 19 M4X8L 62 Cross round head screws M4X12L Cross round head screws 63 20 M4X8L Hex socket head screws

M4X12L 65

152 Hex socket head screws Hex socket head screws 22 Hex socket head screws M4X12L M4X8L Hex socket head screws 25 66 Hex flat head screws M5X25L M3X10L Hex socket head screws Hex socket head screws Hex button head screws 27 67 M5X12L M4X8L Location pins Angular contact ball bearing Standardworkdesk(12.6"X11.8") 05X16L 70

Upper blade

Hex socket head screws 28 Hex socket head screws M5X12L 71 M5X12L Location pins Location pins 05X16L 04X10L

Machine serial number

Thrust bearing M5X10L 51106 29 72 Hex sockethead screws Hex socket head screws 74 M3X8L 30 Hex socket head screws M4X12L Hex headless screws M5X8L 31 Hex socket head screws 75 Hex socket head screws 5X20L 32 M4X20L Square keys Hex socket head screws Scrapbox Location pins 03X10L 76 M5X8L Square keys Hex flat head screws 36 M4X8L 5X20L Hex flat head screws 79 Cam followers CFH10 153 M4X8L Hex socket head screws 81 M3X8L 38 Cross round head screws Hex nuts M3 Location pins 03X10L Fixed button for lower blade pad Tool box Power socket Hex socket head screws 154 Hex socket head screws M3X12L M4X8L 85 Feed adjustment for lower blade pad

Foot switch socket

Hex socket head screws 155 Hex socket head screws M4X16L M4X8L Hex socket head screws Washers 04X2t M4X12L

Item No.:Ad-6

Item No.: Ad-6

B.Safetyinstructions (Before setting up the machine, carefully read all the manual) Parts list

No. Diagram no. Q'ty Q'ty Description No. Description Diagram no.

Make sure the outlet with the correct volgate and type Main shaft D07-05 D06-06 Cam 69 104 Blade is sharp, non-operator please keep away from machine. D05-04 Baseboard 70 Angular contact ball bearing 105 (7206)

D07-06 Bladebase

Main shaft seat D05-13 106 (R6)

Do not put fingers into the safety protector during operating time. Thrust bearing Setscrew 72 107 (51106) (M4X10L)

Fixing nut D07-10 Blade fastening plate 73 108 D05-18

Do not cut staples, paper clips and other metal objects.

Control ring D07-09 74 109 Setscrew (M4X6L)

Always turn off power when changing blade. D07-16 Large bevel gear 75

Small bevel gear

Always turn off power when work completed.

Washer D07-20

C. All kinds of blade

Cam followers 79 (CFH10)

①Upper blades (3 radius upper blades, 1 straight blade, total 4 kinds)

80 Lower blade pad D05-08 (R6) 81 Left fastening plate D06-01 82 Setscrew 83 D06-16 Cam washer 84 Cam baseboard D06-03 Left outer plate D06-04 86 Setscrew (M3X10L)

AD6-K3.5 AD6-K10 AD6-K6 D06-10-1 Return spring 87 Upper blade Upper blade Straight blade Upperblade

Size:R1/8" Size:5/8" Size:R1/4" Size:R3/8" D06-05 88 Baseboard

Lower blade pads (straight blade can be with any kinds of lower blade pad) 89 Right outer plate D06-04

06 Locking handle D06-15 91 (M6) Nut 92 Cam shaft D06-09 Push plate Feed base Positioning plate

Ad6-K3.5-2 Ad6-K6-2 Ad6-K10-2

Lower bladepad Lower bladepad Lower blade pad Slideway D06-17 96 Size:R1/8" Size:R3/8" Size:R1/4"

97 Feed shaft 98 Nut 99 Feed knob 100 Steel ball 101 MP-19 102 D06-02 Right fastening plate

Item No.: Ad-6 Item No.: Ad-6

H. Electronic control system (11ov) D. Standard parts & accessories (total 8 parts) ①Electrical drawing

KM1 12

SA21 Standard work desk -1 pc Maintenance tools: Left and right side guide Tool and scrap box - each 1. Cross-head and flat-head SPINDLE each 1pc 1pc

KM2 screwdriver-each1pc

KA2 15 FOR KT1 2. T-type hex wrench (2.5,3)- each1pc

3. Hex wrench(1.5/2/2.5/3/4)

(do) -each1pc 4. Fuse (4A) - 5 pcs VALVE (OP) AIR

Kt1 Spindle

KA1 Safety protector-1set Marntenance screw set 1. 1/4" upper blade-1 pc Operationalmanual-1book

1. Round-head hexscrew(M4x8)-5pcs 2.1/4"lowerblade pad-10pcs 2. Flat-head hexscrew（M4X8)-10pcs

KA1 SPINDLE 3.1/4" blade base -1 set 3. Truss-head cross screw(M4X8)-5 pcs STOP 4. Socket-head hex screw(M4X12) - 4 pcs 5. Washers (B4X2t) - 4 pcs

E. Optional parts & accessories (total 8 parts) limit switch

Manual start/Reverse Brake limit switch

Power start/stop

Emergency stop Indicator lamy Auto/Monuol Foot switch P28 25 Straight blade base Upper blade L guide Straight blade

Bladebase Calibrate gauge Lower blade pad Oilstone

Motor

Brake Dc/90V

WIRE-0.75mm² + 3C

1PH 110VAC 50/60HZ MOTOR MOTOR

Power Supply

Item No.: Ad-6 Item No.: Ad-6

F. Machine operation CAUTioN:Beforeoperatingmachine,carefullyread all themanual ①Installation and cutting test

As shown lubricate thefeeding threadand shaft,apply with a little lubrication while rotating.

1. Remove the left and right sideguide and work desk.
2. Lubricate the movement blade pad feeding device.

Place the work desk onto the machine as shown. Place machineon topof a sturdy work table. Align the machine screwholes to the12mounting holes as arrows indicate. 2holes for right side guide 2.5mm hex wrench reference line Asshownwhen the scrap box accumulated uptoseven full please empty the scrap,in order to prevent the risk whenupper bladework down cutting. As arrow 1 shown the 2holes are for right side guide Takethe2.5mmhexwrench,fasten the12pcsflat-head hexscrew(size:M4x8). hole. 2shown the reference line for the right side guide place and adjust the reference.

③Blade sharpened (K3.5/K6/K10 upper blades and straight blade are all available to sharpen by oil stone) upper blade right side gulde lower blade pad 3mm hex wrench 6d Blade is sharp,donot touch with finger.

Abovefigure show the ready position for right andleft

Place front edge of the right side guide on the central As shown putradiusV-shaped blade ontheoil stone. side guide. referenceline,targetthe2-holeshowninP40onthe Add a little lubricateon theoll stone,smooth moves fixed holes. back andforth sharpened blade. Use3mmhexwrenchlocktheM4x12socket-headhexscrew. For straight blade, same operation as radius blade. Fixed left side guide same as above.

Itemno.:Ad-6 Item No.: Ad-6

G. Maintenance ① Changing fuse and discharge capacitor

Emergency stop select button

Auto/Manual select button

Rrectvolt

Power switch

1. Turn on thepower switch motor is standby,thelight (Attention:Make sure the correct voltage)

Replace thefuse Before disassembly the circuit,user must to discharge the

Plug foot switch cord into the socket,then power is on but motor not rotation.

1. Unplug the power cord. capacitor'ssurpluselectricity.Andpayattentionfingersdo 2. Turn the operation mode to manual. cord 2 into the socket. not to touch themetal partwhen using the screwdriver.

2. Takeflat-head screwdriver,pry-open the holeas 3. Push-downmanualstartbutton,push-down tostart 1. Use theflat-head screwdriver pry open the cover of the picture shown outward, pull out the fuse holder by release tostopmotor,makeupperbladeslowlydown anotherhand. terminal blocks. intermittentlytouchthelowerbladepad,checkbladeif 2. Use the cross-head screwdriver to hold the M5junction

3. Remove the damaged fuse and replacea new one readyforworking.(bladehasbeencalibratebyoriginal) that meet the specification,then re-plug the power ofthe screw,and useflat-head screwdriver to hold the cord for using. M6junctionof thescrew,thenmoveboth screwdriver from the touch.

3. After disassembly,replace the cover of the terminal blocks. 2Lubrication applying(Refuel lubricantevery30daysfor using frequently. for not often use every 90 days)

Foot switch

gear protector cover

1. Turn the operation mode to auto.(for manual mode, Put one sheet of paper close torightand leftside leave the upper blade slightly off the top position, guide.(Keepfinger out of safety protector)Stepthe foot switch for cutting testing. and step on the foot switch to start)

When the upper blade to riseup,if heard asharp

2. Testwith thefoot switch see if normal operation. noise.Canbeadd a little lubricating oil on upper (push-down the switch to finishing a cycle,release blade'sflank then dried toresolve the noise.) thefoot switch then start again)

1. Turn off power,unplug the power cord. As shown smeara little grease lubricant onbevelgear,

2. Remove the10pcsscrewofoutsidetheshield,both then covered the gear protector coverby the2pcs handshold the shield and move upward slowly. fixing screws and fasten tightly.

3. As shown remove the 2 pcs screw on gear protector cover.

4. Move the gear protector upward slowly.

1. Release the fixed button of lowerblade padcounter- Checkif the comer rounder is tidy orany cuttingedge remain.If yes,make a newlower bladepad cuttingis clockwise.

2. Fixed button can be pulled out and turn around to requested.How to operate as shown P50-P51. change position.Adjusted to thebest position between scrap box and tool box.

Asshown isthecamtrackforlubrication,takefew

As shownisthelubricatinglinearslider(2sliderseach

3. To lock,hold the handle while rotating clockwise and

left and right),carefully press alittle grease lubricant lubricantbyflat-headscrewdriverandspreadlubricant

inward to press.

on both sides of cam track. by grease nozzle into the sliders.

Itemno.:Ad-6 Item No.:Ad-6

d.Changingthe straightbladeC15

Turm counterclockwise one section of feed adjustment 1. Tumoffpower and release the front plate. 1. Picture shown howto change newC15blade. as shown,the lower blade pad will move 0.125mm.(one time 2. Use left hand's hold upward the white protector to 2. First, put on the white protector on used blade,take onesection can getbetter incision)Then lock the fixed 2.5mm T-type hex wrench to remove the 4 pcsfixing thebaseand close to the positioningplate,right button and try cuttingagain,if the situation remains the hand take3mmT-typehexwrenchandscrewtightly screws. same,pleaserepeatP50-P51.(a lower blade padcanbe the2pcs of M4X16screws,make surefasten tightly. 3. Same,put onthewhite protector on new blade before use 80 sections) 3. Remove the white protector,andreplace front changing.Replace it on bladebase then 4 pcs of fixing

screw,make sure screws fasten tightly. plate.The C15bladeisnow complete.

② Right and left side guide adjustment

④ How to use the "L" guide

cut is good no need to adjust cut is too much need to move inward

three reference lines

Above shown the right side cutis good no need to Release2fixedscrewonleftsideguide.Referthethreelines adjust.Left side cut is too much need to move inward onworkdesk,arrowisthedirection of inward movement,

Adjust the safety protector and keep stack of paper Put the"L" guide on table,use"L" guide left and right

ofleftpaper guide. keep front edge of the left side guide and reference line are

about5mmheight distance,fixtheadjustbutton.

parallel then fixed it for once cutting.

neatly.At the same time,make sure"L"guide close to

if the situation remains the same,pleaserepeat abovepro-

the outside cornerof the paper.Right hand fingers hold

cedures unit getperfect corner rounder. "L"guide at the bottom(as shown)，slightly press the"L

guide let it close to the paper for cutting.

b.With calibrate gauge

Keep calibrate gauge close toright and left sideguide. As drawing shown theleft cut is too much need to Checktherelativepostionbetweencalbrategauge and adjust left side guide toright.Drawing2is the perfect right sideguide,micro adjustment the calibrate gauge cutting after adjustment. toright asredarrow shown.Hold thegauge withright handand loosenthe2pcsfixedscrewofleftsideguide bylefthand,then move the left side guide close to calibrate gauge andfixed tightly.

Itemno.:Ad-6 Itemno.:Ad-6

cut is too little no need to adjust need to move outward of left side gul de

Takescrewdrivertogetbottom-underthelowerblade Take short-side of 3mm hex wrench and push fnside to As drawing shown left cut is too little need to move outward new lower bladepad holeforfixing(as shown),thentake pad, forward the pad to scrap box. (toleft)of left side guide. hex wrench align to the guider and push down until touch tothe end.Then take the hex wrench outandlock the fixedbutton of lower blade pad.

③ Changing blades

a. Changing the upper blade

c. Changing the blade base

locating pin

1. Turn off the power. Caution:V-typeblade is sharp,donot touch withfingers.
2. Remove the front plate. As shown use left hand two finders hold on bottom of

Use finger push and forward the blade base to scrap box 3. Take2.5mmT-typehexwrench,counterclockwise Attention:Turnoffthepowerfirst upper blade, andhold the top withright hand indexfinger,

1. Blade base corresponding to upper blade,Ex: and take thebase out. loosen 4 pcs of fixed screw. slow-shaketoremove thebladeout. K6 blade base use for K6 upper blade. Same as above take a newblade,aligned and pressinward
2. Take 2.5mm hexwrench to loose2pcsoffixed screws. to the2locatingpinasarrow shown.Take2.5mmT-type

hex wrench tolook the 4pcs screw.(Please check again for well looking)

b.Changing the lower blade pad (3upperblade with3 lowerblade;Ex:K6lowerbladewithK6upperblade)

Toolbok

securlty gaps

1. Install the front plate.

Take thenewbase,install the base plate from the

2. Turn on thepower and keep manual button,Usemanual front and pull back to the end, not lock now. start button operation and stop upper blade on lowest

Turn offthepower,relaesethefixedbutton oflower Asphoto shown,rotate thefeed adjustment in a

point. bladepad counterclockwise. clockwise to the end.

3. Turn off the power and remove the front plate.
4. Push andforward the bladebase align with fixed hole. Checkif enough security gaps between upper blade and bladebase before fixing.(Please check again for well

Itemno.:Ad-6 Itemno.:Ad-6

cut is too little no need to adjust need to move outward of left side gul de

Takescrewdrivertogetbottom-underthelowerblade Take short-side of 3mm hex wrench and push fnside to As drawing shown left cut is too little need to move outward new lower bladepad holeforfixing(as shown),thentake pad, forward the pad to scrap box. (toleft)of left side guide. hex wrench align to the guider and push down until touch tothe end.Then take the hex wrench outandlock the fixedbutton of lower blade pad.

③ Changing blades

a. Changing the upper blade

c. Changing the blade base

locating pin

1. Turn off the power. Caution:V-typeblade is sharp,donot touch withfingers.
2. Remove the front plate. As shown use left hand two finders hold on bottom of

Use finger push and forward the blade base to scrap box 3. Take2.5mmT-typehexwrench,counterclockwise Attention:Turmoffthepowerfirst upperblade,and hold the top with right hand indexfinger,

1. Blade base corresponding to upper blade,Ex: and take thebase out. loosen 4 pcs of fixed screw. slow-shaketoremove thebladeout. K6 blade base use for K6 upper blade. Same as above take anewblade,aligned and pressinward
2. Take 2.5mm hex wrench to loose2pcsoffixed screws. to the2locatingpinasarrow shown.Take2.5mmT-type

hex wrench tolook the 4pcs screw.(Please check again for well looking)

b.Changing the lower blade pad (3upperblade with3 lowerblade;Ex:K6lowerbladewithK6upperblade)

Toolbok

securlty gaps

1. Install the front plate.

Take thenewbase,install the base plate from the

2. Turn on thepower and keep manual button,Usemanual front and pull back to the end, not lock now. start button operation and stop upper blade on lowest

Turn offthepower,relaesethefixedbutton oflower Asphoto shown,rotate thefeed adjustment in a

point. bladepad counterclockwise. clockwise to the end.

3. Turn off the power and remove the front plate.
4. Push andforward the bladebase align with fixed hole. Checkif enough security gaps between upper blade and bladebase before fixing.(Please check again forwell

Itemno.:Ad-6

Item No.: Ad-6

d. Changing the straight blade C15

Turn counterclockwise one section of feed adjustment 1. Turn off power andrelease thefront plate. 1. Picture shown howto changenewC15blade. as shown,the lower blade pad will move 0.125mm.(one time 2. Useleft hand's hold upward the white protector to 2. First, put on the white protector on used blade,take onesection can getbetter incision)Then lock the fixed 2.5mmT-typehex wrench to remove the4pcsfixing the baseand closeto the positioning plate,right button and try cuttingagain,if the situation remains the screws. same,pleaserepeatP50-P51.(a lowerblade padcan be the2pcs of M4X16screws,make surefasten tightly. 3. Same,putonthewhiteprotectoronnewbladebefore use 80sections) 3. Remove the white protector,andreplace front changing.Replace it on blade base then 4 pcs of fixing

screw,make sure screws fasten tightly. plate.TheC15bladeis nowcomplete.

②Right and left side guide adjustment a.Without calibrate gauge

④ How to use the "L" guide

cut is good no need to adjust cut is too much need to move inward

three reference lines

Above shown the right side cutis good no need to Release2fixedscrewonleftsideguide.Referthethreelines adjust.Leftside cutis too muchneed to move inward onworkdesk,arrowisthe direction ofinward movement,

Adjust the safety protector and keep stack of paper Put the"L" guide on table,use"L"guide left and right

ofleftpaper guide. keep front edge of the left side guide and reference line are

about5mmheight distance,fixtheadjustbutton.

parallel then fixed it for once cutting.

neatly.At the same time,make sure"L"guide close to

If thesituationremainsthesame,pleaserepeatabovepro- theoutsidecornerofthepaper.Righthandfingershold cedures unit get perfect corner rounder.

"L"gulde at the bottom(as shown),slightly press the"L" guide let it close to the paper for cutting.

b.With calibrate gauge

Keep calibrate gauge close toright and left sideguide. As drawing shown the left cut is too much need to Check the relative position between calibrate gauge and adjustleft sideguidetoright.Drawing2istheperfect rightsideguide,microadjustmentthecalibrategauge cutting after adjustment. toright asredarrowshown.Hold thegauge withright hand and loosen the2pcsfixedscrewofleftsideguide by lefthand,thenmove theleft sideguide close to calibrate gauge andfixed tightly.

Itemno.:Ad-6 Item No.: Ad-6

G. Maintenance ① Changing fuse and discharge capacitor

Emergency stop select button

Auto/Manual select button

Rrectvolt

Power switch

1. Turn on thepower switch motor is standby,thelight (Attention:Make sure the correct voltage)

Replace thefuse Before disassembly the circuit,user must to discharge the

Plug foot switch cord into the socket,then power is on but motor not rotation.

1. Unplug the power cord. capacitor'ssurpluselectricity.Andpayattentionfingersdo 2. Turn the operation mode to manual. cord 2 into the socket. not to touch themetal partwhen using the screwdriver.

2. Takeflat-head screwdriver,pry-open the holeas 3. Push-downmanualstartbutton,push-down tostart 1. Use theflat-head screwdriver pry open the cover of the picture shown outward, pull out the fuse holder by release tostopmotor,makeupperbladeslowlydown anotherhand. terminal blocks. intermittentlytouchthelowerbladepad,checkbladeif 2. Use the cross-head screwdriver to hold the M5junction

3. Remove the damaged fuse and replacea new one readyforworking.(bladehasbeencalibratebyoriginal) that meet the specification,then re-plug the power ofthe screw,and useflat-head screwdriver to hold the cord for using. M6junctionof thescrew,thenmoveboth screwdriver from the touch.

3. After disassembly,replace the cover of the terminal blocks. 2Lubrication applying(Refuel lubricantevery30daysfor using frequently. for not often use every 90 days)

Foot switch

gear protector cover

1. Turn the operation mode to auto.(for manual mode, Put one sheet of paper close torightand leftside leave the upper blade slightly off the top position, guide.(Keepfinger out of safety protector)Stepthe foot switch for cutting testing. and step on the foot switch to start)

When the upper blade to riseup,if heard asharp

2. Testwith thefoot switch see if normal operation. noise.Canbeadd a little lubricating oil on upper (push-down the switch tofinishing a cycle,release blade'sflank then dried toresolve the noise.) thefoot switch then start again)

1. Turn off power,unplug the power cord. As shown smeara little grease lubricant onbevelgear,

2. Remove the10pcsscrewofoutsidetheshield,both then covered the gear protector cover by the2pcs hands hold the shield and move upward slowly. fixing screws and fasten tightly.

3. As shown remove the 2 pcs screw on gear protector cover.

4. Move the gear protector upward slowly.

1. Release the fixed button of lowerblade pad counter- Checkif the comer rounder is tidy orany cuttingedge remain.If yes,make a newlower bladepad cuttingis clockwise.

2. Fixed button can be pulled out and turn around to requested.How to operate as shown P50-P51. change position.Adjusted to thebest position between scrap box and tool box.

Asshown isthecamtrackforlubrication,takefew

As shownisthelubricatinglinearslider(2sliderseach

3. To lock,hold thehandle while rotating clockwise and

left and right),carefully press alittle grease lubricant lubricantbyflat-headscrewdriverandspreadlubricant

inward to press.

by grease nozzle into the sliders. on both sides of cam track.

Item No.: Ad-6 Item No.: Ad-6

F. Machine operation CAUTIoN: Before operating machine, carefully read all the manual ① Installation and cutting test

As shown lubricate the feeding thread andshaft,apply

1. Remove the leftand right side guide and work desk. with a little lubrication while rotating.
2. Lubricate the movement blade pad feeding device.

Place the work desk onto the machine as shown. Place machine on top of a sturdy work table. Align the machine screw holes to the 12 mounting holes as arrows indicate. 2holes for right side guide 2.5mm hex wrench reference line As shown when the scrap box accumulated uptoseven when upperblade work down cutting.

As arrow shown the 2holes are forright side guide hex screw(size:M4x8). hole.

place and adjust the reference.

3Blade sharpened(K3.5/K6/K10 upper blades and straight blade are all available to sharpenby oil stone) upper blade right side gulde lower blade pad 3mm hex wrench P95 Blade is sharp,do not touch with finger. Above figure show the ready position for right andleft Place front edge of the right side guide on thecentral As shown put radius V-shaped blade on the oil stone. side guide. referenceline,target the2-hole shown fnP40on the Add alittle lubricate on theoil stone,smoothmoves fixed holes. back andforth sharpened blade. Use3mm hexwrench lock theM4x12socket-headhexscrew. For straight blade, same operation as radius blade. Fixed left side guide same as above.

Item No.: Ad-6 Item No.:Ad-6

H.Electronic control system (11ov) D. Standard parts & accessories (total 8 parts) ① Electrical drawing

KM1 12

SA2 1 Maintenance tools: Standard work desk - 1 pc Left and right side guide Tool and scrap box - each 1. Cross-head and flat-head

SPINDLE each 1pc 1 pc screwdriver-each1pc

15 FOR 2. T-type hex wrench (2.5,3) - each1pc

3. Hex wrench(1.5/2/2.5/3/4)

OP 4. Fuse (4A) - 5 pcs VALVE AIR

Kt1 Spindle Er

SPINDLE START P158 D6d

KA1 Safetyprotector-1set Maintenance screw set 1. 1/4" upper blade -1 pc Operational manual-1book

1. Round-head hexscrew(M4X8)-5 pcs 2. 1/4" lower blade pad - 10 pcs

KA1 2. Flat-head hex screw(M4X8) -10 pcs SPINDLE 3.1/4" blade base -1 set

4. Socket-head hex screw(M4X12)-4pcs

SQ2 5. Washers (@4X2t) · 4 pcs

SA11 AV110V PILOT LIGHT E. Optional parts & accessories (total 8 parts)

limit switch Manual start/Reverse Brake limit switch Indicator lamy.

Foot switch

SB1 P28

Straight blade L guide Straight blade base

Bladebase Calibrate gauge Lower blade pad Oilstone

Motor

Brake Dc/90V

1PH 110VAC 50/60HZ

Power Supply

Itemno.:Ad-6

②Position chart

Pwer

Reverse Aut Eng Stop On-Off

Sa2 Sa1 Sb1 Sb2

No Nc Nc

Manual

Manual

Start

Time

Ka1 Ka2]

K T1 Km1 Km2

Any-2 My2- -Nj -Nj My2

12 M6

25628910UM6VM5

Mdtor

M6 M5

Fuse

Motor

Brake Xs2 Power Xs1 Ac-110V

Item No: Ad-6

I. Diagram and parts list After service will request below information: 1. Modelnumber

2. Machine serial number (marked behind on machine)

①Machinemain structure 3. Parts number,name and quanty

We reserves theright to change the design

Item No.: Ad-6

Parts list

No. Q'ty Q'ty Description No. Description Diagram no. Diagram no. Power socket 49 Inner shutter Foot switch socket 50 D05-02 Middle structural plate D03-03 Front structural plate Back plate 51 Main base 52 D01-01 Right back fixing plate D03-04 Left back fixing plate 53 D01-06 Adjustable leg-glides Condenser 54 Adjustable nut D01-08 Large relay Left cover 55 D03-02 Gear protector cover D04-08 56 D07-11 Magnet seat 57 Back shutter 10 D01-10 Small relay 11 Terminal blocks seat D04-09 Relay base D04-02 Terminal blocks 12 Brake limits switch 13 LS fixing plate Relay guide seat D04-01 D04-10 61 Motor base 14 Rectifier D04-03 62

Earth copper plate

15 Main shaft system Followed by details 63 16 Main structural D02-01-1 Scrap box D04-05 Reinforcement axle D14-09 D01-03 65 17 Left scrap plate 66 Right cover 18 Upper scrap plate D01-02 Upper blade (R6) D09-11 Middle scrap plate 19 67 D01-05 20 68 Emergency stop switch Right scrap plate D01-04 22 D14-07 120 Slide block D16-03 Lower fixing axle 23 Tool box 121 Slideway D16-02 D04-06 24 123 Safety protector D16-01 LG washer D04-07 25 Linear guideway 124 adjust button D16-04 125 Location axle 27 CF upper guide D16-06 D07-13 28 151 Outside the shield CF lower guide D13-01 D07-14 29 Middle fixing axle 152 D14-08 Main slide seat D07-01 Front plate 30 Limiting board 153 D14-02 D07-15 31 FrontLS fixing plate D14-06 Upper fixing axle D02-08 32 Right side guide Blade base D07-08 D02-05-1 33 Power switch Left side guide D02-04-1 34 Function switch 157 Standard work desk D15-01-1 Manual start switch Motor 35 158 (100W) 36 Control parts plate D14-01 38 End cover limits switch Calibrate gauge 42 D02-06 L guide 45 Back pad D02-02 46 Front pad D02-03 47 Lower blade system Followedby details Back structural plate "# Standard hardware parts

Item No.: Ad-6

After service will request below fn formation:

2Parts of structure:Main shaft system and Lower blade system 1. Model number

2. Machine serial number(markedbehind onmachine)
3. Parts number,name and quantity

Main shaft system Lower blade system

Wereserves the right to change thedesign

Item No.: Ad-6

Item No.: Ad-6

B. Safety instructions (Before setting up the machine, carefully read all the manual) Parts list

No. Q'ty Description Diagram no. Description Diagram no. No.

Make sure the outlet with the correct volgate and type D07-05 Main shaft D06-06 69 Cam 104 Blade is sharp, non-operator please keep away from machine. Angular contact ball bearing Baseboard D05-04 70 105 (7206)

Blade base Main shaft seat D05-13 71 106 (R6)

Do not put fingers into the safety protector during operating time. Thrust bearing 72 107 Setscrew (M4X10L)

73 Fixing nut D07-10 Blade fastening plate 108 D05-18

Do not cut staples, paper clips and other metal objects.

Control ring D07-09 74 109 (M4X6L) Setscrew

Always turn off power when changing blade. D07-16 Large bevel gear 75

Small bevel gear

Always turn off power when work completed.

78 Washer

C. All kinds of blade

79 (CFH10) Cam followers

Upper blades (3 radius upper blades, 1 straight blade, total 4 kinds)

80 D05-08 (R6) Lower blade pad 81 Left fastening plate D06-01 82 Setscrew (M3X6L) 83 D06-16 Cam washer 84 Cam baseboard D06-03 Left outer plate 86 Setscrew (M3X10L)

AD6-K3.5 AD6-K10 AD6-K6 D06-10-1 Return spring 87 Upper blade Upper blade Straight blade Upperblade

Size:R1/8" Size:R1/4" Size:R3/8" Size:5/8" D06-05 88 Baseboard

Lower blade pads (straight blade can be with any kinds of lower blade pad) 89 Right outer plate D06-04

06 Locking handle D06-15 91 (M6) Nut 92 Cam shaft D06-09 Push plate D06-12 Feed base D06-11 Positioning plate

Ad6-K3.5-2 Ad6-K6-2

Lower blade pad

Lower blade pad Lower blade pad Slideway D06-17 96 Size:R1/8" Size:R1/4" Size:R3/8"

97 Feed shaft 98 Nut 99 Feed knob Steel ball (03) 101 MP-19 102 Right fastening plate D06-02 Shrink-ring D06-07 "# Standard hardware parts

Item No.: Ad-6

Item No.: Ad-6

4 Screws and other standard hardware parts list A. Name of machine parts No. Specifications Q'ty No. Specifications Qty Hardware description Hardware description 156 Hex socket head screws M4X16L Hex flat head screws M3X10L Hex button head screws 04X2t

M4X8L M4X8L

Hex button head screws 157 Hex flat head screws Powerswitch Auto/Manual select button 45 Hex flat head screws M3X10L Hex socket head screws M4X6L Emergency stop Reverse/Manualstartselectbutton M4X6L Hex flat head screws

Hex socket head screws M3X10L

Hex socket head screws 48 Hex socket head screws M4X12L M4X6L 49 Hex socket head screws Hex flat head screws M4X8L 10 M4X6L 151 Front plate Hex socket head screws Hex socket head screws M4X12L M4X8L 50 Hex socket head screws Hex socket head screws M4X8L 51 M4X12L 11 Adjust button for

safety protector

Cross round head screws 12 54 M3X16L 08x2t 13 Hex socket head screws Hex flat head screws M4X6L 10 55 M4X8L Left side guide Hex flat head screws Hex socket head screws 14 M6X20L M4X8L Washers 158 Hex socket head screws 06X2t M8X25L Right side gulde Hex nuts 08x2t

Lower blade pad Safety protector

Hex nuts

16 Hex socket head screws M5X10L M8 Location pins Cross round head screws 05x10L 59 17 M4X8L 60 M4X10L Cross round head screws Hex socket head screws 18 Hex socket head screws 61 Hex socket head screws M4X8L M4X8L

Standard work desk(12.6"X11.8")

Hex socket head screws 19 M4X8L 62 Cross round head screws M4X12L 20 Cross round head screws M4X8L Hex socket head screws

M4X12L M4X12L 65

152 Hex socket head screws Hex socket head screws 22 M4X8L M4X12L Hex socket head screws Hex sockethead screws 25 66 Hex flat head screws Hex socket head screws M5X25L M3X10L Hex socket head screws Hex button head screws 27 67 M5X12L M4X8L Angular contact ball bearing Standard work desk (12.6"X11.8") Location pins 05X16L 70

Upper blade

Hex socket head screws 28 Hex socket head screws M5X12L 71 M5X12L Location pins Location pins 05X16L 04X10L

Machine serial number

Thrust bearing Hex socket head screws 51106 29 72 Hex socket head screws 74 M3X8L 30 Hex socket head screws M4X12L Hex headless screws 31 Hex socket head screws 75 M5X8L Hex socket head screws 5X20L 32 M4X20L Square keys Hex socket head screws Scrapbox Location pins 03X10L 76 M5X8L Square keys Hex flat head screws M4X8L 36 5X20L Hex flat head screws Cam followers CFH10 79 153 M4X8L Hex socket head screws M3X8L M3X20L 81 38 Cross round head screws Hex nuts M3 Location pins 03X10L Fixed button for lower blade pad Tool box Power socket Hex socket head screws 154 Hex socket head screws M4X8L M3X12L 85 Feed adjustment for lower blade pad

Foot switch socket

Hex socket head screws Hex socket head screws 155 M4X16L M4X8L Hex socket head screws Washers 04X2t M4X12L

TABLE OF CONTENTS ITEM NO.: AD-6 ITEM NO.: AD-6

A. Name of machine parts ...

No. Specifications Q'ty Hardware description No. Specifications| Q'ty Hardware description

B. Safety instructions ..

85 Location pins

C. All kinds of blade Location pins 05X12L ① Upper blades.... Hex socket head screws M3X12L 89 2 Lower blade pads Hex socket head screws M4X8L

Hex socket head screws M4X12L

D. Standard parts & accessories

Location pins 03X12L

E. Optional parts & accessories

Location pins 05X12L

F. Machine operation Location pins 93 05X28L ① Installation and cutting test .. 94 Hex socket head screws M4X28L

Location pins 05X10L

2Rightand left side guide adjustment

Steel ball

a. Without calibrate gauge ...

Hex socket head screws 102 M3X8L

b. With calibrate gauge ...

Location pins 03X10L

③ Changing blades

105 M4X10L Hex socket head screws

a. Changing the upper blade ...

106 Hexflat head screws

b. Changing the lower blade pad .

Hexflathead screws M4X6L

c. Changing the blade base 108

Location pins 04X6L

d. Changing the straight blade C15 ④ How to use the "L" guide ·.

G. Maintenance ① Changing fuse and discharge capacitor .. 2 Lubrication applying 11 ③ Blade sharpened .... 12

H. Electronic control system ① Electrical drawing.... 13 2 Position chart .... 14 I. Diagram and parts list ①Machine main structure 2 Parts of structure: Main shaft system and Lower blade system ........· 17

Electric Corner Rounding Machine

Specifications

Item No. AD-6

Operational Manual

Radius 3/8" Four Kinds of Blades length 5/8" Straight Cutting Capacity 23.6" (600 sheets ) Cutting Speed 46 rpm Dimensions 24.6"(W) X 12.6"(D) X 17.5"(H) Weight / Volumn

Power 110vac (50~60Hz)

Item No: Ad-6