Akiles Diamond 7 Operation Manual

Specifications

Item No. AD-7 Radius 3/8"

Seven Kinds 1/2" 5/8"

of Blades Half Moon diameter 13/16" Straight length 5/8" Cutting Capacity 27.56" ( 700 sheets ) Cutting Speed 46 rpm Dimensions 24.6"(W) X 12.6"(D) X 17.5"(H) Weight / Volumn 110 Ibs / 3.14 CbFt Power 110vac (50~60Hz)

Item No.:Ad-7

Table Ofcontents Item No.: Ad-7 Item No.: Ad-7

A. Name of machine parts ....

No. Specifications Q'ty Hardware description No. Specifications| Q'ty Hardware description

B. Safety instructions ...

85 Location pins

C. All kinds of blade 05X12L Location pins ① Upper blades.... Hex socket head screws M3X12L 89 2 Lower blade pads Hex socket head screws M4X8L

Hex socket head screws M4X12L

D. Standard parts & accessories

Location pins 03X12L

E. Optional parts & accessories

Location pins 05X12L

F. Machine operation Location pins 93 05X28L ① Installation and cutting test ... 94 Hex socket head screws M4X28L

Location pins 05X10L

②Right and left side guide adjustment

Steel bal1 03

a. Without calibrate gauge ....

Hex socket head screws 102 M3X8L

b. With calibrate gauge ....

Location pins 03X10L

③ Changing blades

105 M4X10L Hex socket head screws

a. Changing the upper blade ....

106 Hexflat head screws

b. Changing the lower blade pad

108 M4X6L

C. Changing the blade base Hexflat head screws

d. Changing the half moon blade D21 Location pins 04X6L

e. Changing the straight blade C15 M4X12L 110 Hex socket head screws

112 M3X6L Hex flat head screws

④ How to adjust the D21 regulator .... 11

114 Hexflathead screws M3X5.5L

How to use the "L" guide .... 11

Hex flat head screws 118 M4X34L

How to use the micro paper guide 12 E-ring 119 04 Spring replacement for paper pressure M3X3.8L 121 Hex flat head screws

a. Dischange the old spring M3X6L 132 Hex flat head screws

b. Spring replacement ... 14 M4X10L 133 Hex flat head screws G.Maintenance Hex socket head screws 134 M4X8L ①Changing fuse and discharge capacitor Hex socket head screws 137

138 M4X12L

② Lubrication applying Hex socket head screws

Hex socket head screws M4X29L

③ Blade sharpened ... 17

139 M5X16L Hex socket head screws

H. Electronic control system M4X10L Hex flat head screws 142 ① Electrical drawing... 143 Hex socket head screws M4X50L ② Position chart ... Hex socket head screws 146 M3X8L

149 Hex socket head screws

I. Diagram and parts list

150 Hex headless screws

① Machine main structure 19 2 Parts of structure: Main shaft system and Lower blade system .. 3Parts of structure:Paper pressure system and Micro adjustment'paperguidesystem... 4Screws and other standard hardware parts list.....

Item No.: Ad-7

Item No.: Ad-7

4Screws and other standard hardware parts list A. Name of machine parts No. Specifications No. Hardware description Q'ty Hardware description Specific at lons Q'ty Hex socket head screws M4X16L Hex flat head screws M3X10L 41 Washers 04X2t Hex button head screws Quick-release button 44 Hexflat head screws 12

M4X8L M4X8L

Hex button head screws Auto/Manualselectbutton Power switch

Hex socket head screws 45 Hex flat head screws Emergency stop M4X6L Reverse/Manualstartselectbutton 46 Hex flat head screws Hex socket head screws M4X6L M3X10L Outside the shield Hex socket head screws Hex socket head screws M4X12L M4X6L

Paper pressure Front plate

49 Hex socket head screws Hex flat head screws M4X8L 10 M4X6L Hex socket head screws Hex socket head screws M4X8L M4X12L 50

Adjust button for

Hex socket head screws

M4X8L 51 M4X12L

11 Hex socket head screws safety protector Cross round head screws M3X16L 12 54 08x2t

Left side guide

13 Hex socket head screws Hex flat head screws M4X6L 55 M4X8L Hex flat head screws Hex socket head screws 57 M6X20L 14 M4X8L

Right side guide

Washers 06X2t 58 Hex socket head screws M8X25L Hex nuts M6 Washers 08x2t Safety protector Lower blade pad

Hex nuts

16 M5X10L M8 Hex socket head screws Location pins 05x10L 59 Crossround head screws

M4X8L M4X10L

17 Cross round head screws Hex sockethead screws 18 Hex socket head screws 61 Hex socket head screws M4X8L M4X8L

Standard work desk (12.6"X11.8")

Hex socket head screws 19 M4X8L 62 Cross round head screws M4X12L 20 Cross round head screws M4X8L Hex socket head screws Hex socket head screws M4X12L 65 M4X12L 21 Hex socket head screws 22 M4X12L M4X8L Hex sockethead screws Hex socket head screws 25 66 Hex flat head screws M5X25L M3X10L Hex socket head screws 27 Hex socket head screws Hex button head screws 67 M5X12L M4X8L Standardworkdesk(12.6"X11.8") Location pins Angular contact ball bearing 05X16L 70 Upperblade Hex socket head screws 28 Hex socket head screws 71 M5X12L M5X12L Location pins Location pins 05X16L 04X10L

Machine serial number

Thrust bearing M5X10L 51106 29 72 Hex socket head screws Hex socket head screws 74 M3X8L 30 Hex socket head screws M4X12L Hex headless screws M5X8L 31 Hex socket head screws 75 Hex socket head screws 5X20L 32 Square keys M4X20L Hex socket head screws Location pins 03X10L 76 M5X8L Scrap box Square keys Hex flat head screws 36 M4X8L 5X20L 37 Hex flat head screws 79 Cam followers CFH10 M4X8L Hex socket head screws 81 M3X8L 38 Cross round head screws Hex nuts M3 Location pins 03X10L Fixed button for lower blade pad Tool box Power socket Hex socket head screws Hex flat head screws M3X12L 39 M4X8L 85

Feed adjustment for lower blade pad Foot switch socket

Hex socket head screws Hex socket head screws 40 M4X16L M4X8L Hex socket head screws Washers 04X2t M4X12L

Itemno.:Ad-7 Itemno.:Ad-7

B.Safetyinstructions (Before setting up the machine, carefully read all the manual) Parts list

No. Diagram no. Q'ty Q'ty No. Diagram no. Description Description

Make sure the outlet with the correct volgate and type Washer D10-09 D12-12 110 Right side plate 145 Blade is sharp, non-operator please keep away from machine. Quick-release button D10-17 146 Fixing seat D12-10 111

112 D10-10 Upper plate D12-06 Micro adjustment screw 147

Do not put fingers into the safety protector during operating time. 113 D10-21 148 D12-07 Sleeve Front adjusting nut

114 Fixing plate D10-24 Back adjusting nut D12-08

Do not cut staples, paper clips and other metal objects. 149

Scale ring D12-09

Silencing pad D10-25 150

Always turn off power when changing blade. D10-16 Spring shaft 116

117 Upper cover D10-14

Always turn off power when work completed.

Constant force spring D10-19 119 Hanging spring shaft

C. All kinds of blade

120 Slide block

Upper blades (5 radius upper blades, 1 straight blade, 1 half moon blade, total 7 kinds)

Slideway D16-02

Safety protector D16-01 124 adjust button 125 Location axle 126 Rubber gasket 127 D10-13 Lower cover

AD7-K3.5 AD7-K13 AD7-K6 D10-01 128 Outer cover Upper blade Upper blade Upperblade Upperblade

Size:R1/8" Size:R1/4" Size:R3/8" 129 E-ring (E4)

131 D10-02 Inner cover 132 Space plate 133 Locating axle Quick-releasefront plate

Slide shaft D10-18

AD7-K16 AD7-C15 AD7-D21 Locking spring 136 D06-10-2 Straight blade Upperblade Half moonblade

Size:R5/8" Size:5/8" D10-05 137 Inner plate

2 Lower blade pads (straight and half moon blades can be with any kinds of lower blade pad) D10-08 138 Left side plate

Main plate Setscrew D12-13

142 Panel board D12-02-2 (R) 143 Base (R) D12-01-2

P13 P15

Guideway shaft D12-11

Ad7-K3.5-2 Ad7-K6-2 Ad7-K10-2 Ad7-K13-2 Ad7-K16-2

Lower blade pad Lower blade pad Lower blade pad Lower blade pad Lower blade pad

"# Standard hardware parts

Size:R1/8" Size:R5/8" Size:R1/4" Size:R3/8" Size:R1/2"

Item No.: Ad-7 Item No.: Ad-7

D. Standard parts & accessories (total 8 parts)

Standard work desk -1 pc Maintenance tools: Left and right side guide Tool and scrap box - each

1. Cross-head and flat-head

Size: 12.6"(w)x 11.8"(L) each 1pc 1 pc screwdriver-each1pc

2. T-typehex wrench(2.5,3）- each1pc
3. Hexwrench(1.5/2/2.5/3/4)

• each 1pc

4. Fuse (7A) - 5 pcs

P83-P84is shown how to lubricating for lowerblade pad As shown lubricate the feeding thread and shaft,apply system. withalittle lubrication while rotating.

1. Discharge the paper pressure.
2. Remove the left and right side guide and work desk.
3. Lubricate the movement blade pad feeding device.

1.1/4upper blade-1pc Maintenance screw set Paper pressure - 1 set Operational manual-1book

1. Round-head hexscrew(M4x8)-5pcs 2. 1/4" lower blade pad -10 pcs

2. Flat-head hexscrew(M4x8)-10pcs 3. 1/4" blade base - 1 set

3. Truss-head cross screw（(M4X8)-5pcs

4. Socket-head hex screw(M4X12) - 4 pcs

5. Washers (B4X2t) - 4 pcs

E. Optional parts & accessories (total 13 parts)

P26 P27

As shown when the scrap box accumulated up to seven

Large work desk Straight blade base L guide Straight blade

when upper blade work down cutting. Size: 19.7(w)x 11.8"(L) Size:5/8"

③ Blade sharpened (K3.5/K6/K10 upper blades and straight blade are all available to sharpen by oil stone)

Blade base Half moon blade Lower blade pad

Micro paper guide set

Calibrate gauge Half moon blade regulator Constant force spring

Bladeis sharp,do not touch withfinger. As shown put radius V-shaped blade on the oil stone. Add a little lubricate on theoil stone, smooth moves back and forth sharpened blade. For straightblade,same operation asradius blade. by machine is recommand. Oilstone

Item No.: Ad-7

Item No.: Ad-7

F. Machine operation 2Lubrication applying (Refuel lubricant every 30 days for using frequently.

for not often use every90 days)

CAUTIoN:Before operating machine, carefully read all themanual ① Installation and cutting test Quick-release button

gear protector cover

Quick-release devlce pressure

P77-P80showhowtolubricate the main structure. Asshown smeara little grease lubricant on bevel gear,

1. Turn off power,unplug thepower cord.
2. Removethe10pcsscrewofoutsidetheshield,both fixing screws andfasten tightly.

Place machine on top of a sturdy work table. 1. Pullforward torelease thepaper pressure from hands hold the shield and move upward slowly. quick-release button.

3. As shown remove the2 pcsscrew on gear protector cover.

2. Hold the paper pressure, downward to the end and 4. Move the gear protector upward slowly. pull out the paper pressure, then release the quick- release button. 2.5mm hex wrench 12mounting holes

Asshownisthelubricatinglinearslider(2sliderseach Asshownisthecamtrackforlubrication,takefew

Place the work deskonto themachine as shown. Takethe2.5mmhexwrench,fasten the12pcsflat-head left and right),carefully press a little grease lubricant lubricantbyflat-headscrewdriver andspread lubricant Align themachine screw holes to the12mountingholes hex screw(size:M4x8). by grease nozzle into the sliders. onboth sides ofcam track. as arrows indicate. 2 holes for right side guide right side guide 3mm hex wrench reference line P82

P81-P82show how to lubricate the paper pressure. Takefewlubricantbyflat-headscrewdriver,spreadto

P40 First,discharge the paper pressure. sliding suface up and down as shown for smooth movement.

Place front edge of theright side gufdeonthe central

As arrow shown the 2 holes arefor right side guide 1. Counterclockwise rotation thewhite-ball. referenceline,targetthe2-hole showninP40onthe 2. Take 2mm hex wrench to release the 2 pcsfixing fixed holes. screwswhich under white-ball, then remove the cover.

3. As shown apply a little lubricant on the whole activities

place and adjust the reference. Use3mmhexwrenchlocktheM4x12socket-headhexscrew. Fixedleft side guide same as above. parts.

4. Reinstall the cover and the white-ball.

Itemno.:Ad-7 Itemno.:Ad-7

long nose plier natural state on the shaft Upperblade

Lower blade pad

1. Take the removed E-ringhook onto the shaft groove 1. lefthand hold the outer cover,and right hand hold as shown, and replace it by long-nose plier. the locating axle and slightly pull thespring seeif

2. Becareful hanging thespring natural state on worksupand down smoothly.

2. If cannotmove,need to discharge andre-assembly the shaft,do not hook thespring on shaft groove. Abovefigure show the ready position for right andleft (Attention:Makesurethecorrectvoltage) and test again.

side guide. Plug foot switch cord into the socket, then power cord 2 into the socket.

adjust button

1. Finally,install the safety protector and tighten the

1. Packback theblack rubber bottom coverbyflat-head 4 screws. screwdriver and push close tightly.

2. As above and then loaded upper cover.

1. Pull forward torelease the paper pressure from Loosen theadjust button of safety protector,moveit down to the bottom andlockit.

Keep the safety protector and work deskminimum

2. Hold thepaper pressure,willbe two positioning pins

G. Maintenance clearance 3/8". into the twoholes,upward push to the top and then

release thequick-releasebuttonforauto-lockpaper

① Changing fuse and discharge capacitor pressure.

Emergency stop

Foot switch

Power switch

Beforedisassemblythecircuit,usermustto discharge the

Replace thefuse

1. Unplug the power cord. capacitor'ssurplus electricity.Andpayattentionfingers do

1. Turn the operation mode to auto.(for manual mode,

1. Turn on thepower switch motor is standby,thelight

2. Takeflat-head screwdriver,pry-opentheholeas notto touch the metal part when using the screwdriver.

leave the upperblade slightly off the top position,

1. Use theflat-head screwdriver pry open the cover of the is on but motor not rotation. picture shown outward, pull out the fuseholder by
2. Turn the operation mode to manual. and step on the foot switch to start)

another hand. terminal blocks.

3. Push-down manual startbutton,push-down to start 2. Test with thefoot switch see if normal operation.

3. Remove the damaged fuse and replace a new one 2. Use the cross-head screwdriver to hold the M5junction

release tostopmotor,makeupperbladeslowlydown (push-down the switch tofinishing a cycle,release

thatmeetthespecification,thenre-plug thepower of thescrew,and useflat-head screwdriver to hold the cord for using. the foot switch then start again) M6junction of the screw,then moveboth screwdriver

ready for working.(blade has been calibrate by original)

totouch.Atsame momentwill have sparkles caused from the touch.

3. After disassembly,replace the cover of the terminal blocks.

Item No.: Ad-7 Item No.: Ad-7

b.Spring replacement (P141~P150)

square hole

Put one sheet ofpaper close toright and left side Check if the corner rounder is tidy or any cutting edge guide.(Keepfinger outof safety protector)Step the remain.If yes,make a newlower bladepad cuttingis 1. Replace the spring axle and sleeve to the new spring 1. Push theinner cover tothebottom,referP142for foot switch for cutting testing. requested.How to operate as shown P50-P51. correct direction.As right photo shown the outer center hole,please refer above photo 2 toinstall (Whentheupperbladetoriseup,ifhearda sharp the spring for right direction. cover shaft holeis onupper direction. noise.Canbeaddalittlelubricatingoilonupper 2. Replace the spring washerinto the squarehole as blade'sflank then dried toresolve the noise.)

arrowindicated.(do notput the spring was her at the reverse side.) spring prominent side spring washer hole

1. Release the fixed button of lower blade pad counter- Turm counterclockwise one section of feed adjustment as shown, the lower blade pad will move 0.125mm. (one time clockwise. 1. Turn theouter cover to frontside,driven the spring 1. Left hand hold the outer cover, right hand take the one section can get better incision)Then lock thefixed
2. Fixed button can be pulled out and turn around to from thetop andmakes spring was her holemeet the ready new springset and install toinnercover.Be button and try cuttingagain,if the situation remains the change position.Adjusted to the best position between careful keep the spring prominent side at the left. outer cover hole. same,please repeatP50-P51.(alowerblade pad can be scrap box and tool box. 2. Be carefull the spring fixed gasket fall down, and 2. Replace thefixing screw and fasten tightly. use 80 sections)
3. To lock,hold thehandle while rotating clockwise and prevent the spring sleeve and axle exposedfrom inward to press. spring setfor proper installation.

②Right and left side guide adjustment a.Without calibrate gauge top of the outer cover retafning ring plers outer covershaft hole pad block cut fs good no need to adjust cut is too much need to move inward

three reference lines

1. Remove the inner cover to the top,insert the spring 1. Find a pad block put on the inner cover(4mm above thickness) as arrow shown.

Above shown the right side cut is good no need to Release2fixed screwonleft sideguide.Refer the threelines axlea litteras shown direction.(contraryinsert is

2. Use retaining ring pliers to insert the 2 small holes

adjust.Left side cut is too much need to move inward onworkdesk,arrowisthedirectionofinwardmovement, prohibit) of left side guide. keepfront edge of the left side guide and reference line are on the spring,ask another person to hold the outer parallel thenfixed it for once cutting. cover,pull the spring let shaft pass through thehole

and hold the spring until the shaft go through to

If the situation remains the same,please repeat above pro-

another side shaft hole.

cedures unit get perfect cormer rounder.

Item No.:Ad-7 Itemno.:Ad-7

b.With calibrate gauge

the shaft has corner rounder locating axle

Keep calibrate gauge close to right andleft sideguide. As drawing shown the left cut is too much need to

1. Use small flat-head screwdriver and insert to to 1. If the spring is broken,take out from the shaft Check the relative position between calibrate gauge and adjustleft sideguide to right.Drawing2istheperfect smallholeofE-ring,pulloutwardandremovethe directly. rightsideguide,micro adjustment the calibrate gauge cutting after adjustment. 2. lf springisworthless,useonehandholdthelocating E-ring. (Remove one side the shaft has corner to right as red arrow shown.Hold the gaugewith right axleandslightlypullopenasarrowshown,another rounder) hand and loosen the2pcsfixedscrewofleftsideguide hand takeout the shaft. by lefthand,then move theleft side guide close to

calibrate gauge and fixed tightly.

cut isgood cut is too Little no need to adjust of left slde gulde

As drawing shown left cut is too little need to move outward

1. Use 2.5mm hexwrench release fixing screws for 1. Left hand finger insert into the outercover hole

(to left) of left side guide.

spring washer. and push outward the springas shown,right hand hold the spring and puliit outward.(inside the spring still have other spare parts,do not tiltthe outer cover but straighten for easier take the ③Changing blades spring out)

a. Changing the upper blade

ROUND CORNERING MACHINE locating pin

locating pin WARNING

1. Turn off the power. Caution:V-type blade is sharp,do not touch with fingers.
2. Remove the paper pressure. As shown use left hand two finders hold on bottom of
3. Take2.5mmT-typehexwrench,counterclockwise upper blade, and hold the top with right hand indexfinger, loosen 4 pcs of fixed screw. slow-shaketoremovethebladeout.

①Constant force spring Same as above take a new blade, aligned and press inward

tothe2locating pinas arrowshown.Take2.5mmT-type hex wrench to look the 4pcs screw.(Please check again

③ Spring shaft for well looking) ④ Washer For changingR13&R16radiusupperblade,sameworks

aschanging straightbladeC15.Pleasereferpage10the photo P64, screw tightly with 2 pcs of M4X12 screws.

Itemno.:Ad-7 Itemno.: Ad-7

How touse themicropaperguide(Standard and largework desk can be used)

b.Changing the lower blade pad (5 upper bladewith5 lower blade pad;Ex:K6lowerbladepad withK6upper blade)

postioning hole

sitio ning axle

There are 2pcs of positioning axle on the bottom of left/rightmicro paperguide,nstallthe2pcs of

Tumoff thepower,release thefixed buttonof lower screws by 3mm hex wrench. As photo shown,rotate the feed adjustment in a

positioning axle to fixing positioning hole on work desk.

blade pad counterclockwise. clockwiseto the end.

Asshown turn scalebutton,thecounterclockwisemove Toadjust the micro paperguide,first release the

Takeshort-sideof3mmhexwrench and push inside to

Take screwdriver togetbottom-under the lowerblade white-head screw as shown. toforwardandclockwisetobackward.Eachrotation new lowerbladepadholeforfixing(asshown),then take pad, forward the pad to scrap box. agrid movement is 0.02mm,available movementis hex wrench align to the guider and push down until touch total6mmlenght.Oncethemovementis done,lock- totheend.Thentakethehexwrenchoutandlockthe tightthewhite-headscrew. fixed button of lower blade pad.

Spring replacement for paper pressure

a. Dischange the old spring (P134~P140)

c. Changing the blade base

upper cover 4 pcs screws adjust button plastichook

1. Release the 4 pcs screws by 2mm hex wrench as 1. Take 2pcs smallflat-head screwdriver,insert one

Attention:Turn off the powerfirst Use finger push and forward the blade base to scrap box

driver to the small hole,press down the plastic hook arrow shown.

1. Blade base corre sponging to upper blade,Ex: and take the base out. 2. Hold the adjust button,pull out whole set of safety as shown, and insert another driver to the upper K6bladebaseuseforK6upperblade.

protector from the outer cover. cover among the outer cover and pry the upper cover.

K16 blade base use for K16 upper blade. 2. Remove thebottom cover is same as upper cover.

2. Take 2.5mm hex wrench to loose 2 pcs of fixed screws.

Item No.: Ad-7 Itemno.:Ad-7

4How to adjusttheD21regulator(Mustcomplywiththelargeworkdesk)

scale line

security gaps

locating pln

1. Install the paper pressure.

Take thenewbase,install the base plate from the

2. Turn on the power and keepmanual button,Use manual front and pull back to the end, not lock now.

Put the nut from the backside of large work desk, Foradjusttheregulator,suggesttoreferthescaleline start button operation and stop upper blade on lowest Put the regulator into slot hole in desk as picture of the large workdesk to move theposition.Slightly point. shown align the nut. loosen the screw, you can easily move it. 3. Turn off the power and remove the paper pressure. Take3mm hex wrench and screw tightly the M4X75L 4. Push and forward the blade base align with fixed hole. screw. Check ff enough security gaps between upper blade and

bladebase before fixing.(Please check again forwell

d.Changing the half moon blade D21

Varning

Rning

Notopen

Aution

front plate AUTION NOTCUT

Danger

Danger

put thepaper on desk and move paper close to thefront

1. Turn off the power and release the paper pressure.

plate and left side,till paper touch to the regulator. Take2.5mmT-typehexwrenchtofixthe4screws,make (Caution!Fingers do not exceed the safety protector) 2. Note the sharp blade, put the white plastic protector surescrewsfastentightly.Removethewhiteprotector

before changing.

Onehandslightlypressthepaperandstarttocut.Safe and replace the paper pressure.The D21 blade is now distance between safety protector and paperis5mm. complete. 3. Use left hand's finger hold the white protector, and

right hand'sfingerhold theD21above,aligned and press inward to the 2 locating pin.

5 How to use the "L" guide e.Changingthe straight blade C15

Awarning

Donotopen

Acaution

Adanger

P70 P65

1. Turnoff power and release the paper pressure.

Adjust the safety protector and keep stack of paper Put the"L" guide on table,use"L"guide left and right 1. Picture shown how to change new C15 blade.

2. First,putonthewhiteprotectoronusedblade,take

2. Uselefthand's hold upward the white protector to

edges to tap the stack of paper in parallel till paper is neatly.At the same time,make sureLguide close to thebase andclose to the positioning plate,right 2.5mm T-type hex wrench to remove the 4 pcs fixing the outside corner of thepaper.Righthandfingers hold screws.

3. Same,putonthewhiteprotectoronnewbladebefore

"L"guide at the bottom(as shown), slightly press the"L" the2pcs of M4X16screws,make surefasten tightly. guide let it close to the paper for cutting. changing.Replace it on bladebase then fasten 4 pcs 3. Remove thewhiteprotector,andreplace paper

pressure.The C15 blade is now complete. offixing screw,make sure screws fasten tightly.

Item No.: Ad-7 Itemno.: Ad-7

4 How to adjust the D21 regulator (Must comply with the large work desk)

scale line

locating pin

1. Install thepaper pressure.

Takethenewbase,install thebase platefrom the

P67 2. Tum on the power andkeep manual button,Usemanual front and pull back to the end, not lock now.

Put the nut from the backside of large work desk, Foradjusttheregulator,suggesttoreferthescaleline start button operation and stop upper blade onlowest Put the regulator into slot hole in desk as picture of thelarge workdeskto move theposition.Slightly point. shown align the nut. loosen the screw, you can easily move it. 3. Tum off the power and remove the paper pressure. Take3mm hexwrench and screw tightly the M4X75L 4. Push and forward the blade base align with fixed hole. screw. Checkif enough security gaps between upper blade and

bladebase beforefixing.(Pleasecheckagainfor well

d. Changing the half moon blade D21

Varning

Arning

Notopeh

Laution

front plate AUTION HOTCUT

Danger

Danger

plate and left side,till paper touch to the regulator. Take2.5mmT-typehexwrenchtofixthe4screws,make (Caution!Fingers do notexceed thesafety protector) 2. Notethesharpblade,put the white plastic protector sure screws fasten tightly.Removethewhiteprotector

before changing. and replace the paper pressure.The D21blade is now

One hand slightly pressthepaperandstarttocut.Safe

distance between safety protector andpaperis5mm. complete. 3. Use left hand's finger hold the white protector, and

right hand'sfinger hold the D21above,aligned and press inward to the 2 locating pin.

5 How to use the "L" guide e.ChangingthestraightbladeC15

Awarning

Donotopen

Acaution

Lipsorany

Adanger

1. Turn off power andrelease the paper pressure. 1. Picture shown howto changenewC15blade.

Put the"L" guide on table, use"L" guide left and right

2. First,putonthewhiteprotectoronusedblade,take

edges to tap the stack of paper in parallel tillpaperis about 5mm height distance,fix the adjust button. 2. Useleft hand'shold upward the white protector to

2.5mmT-type hex wrench to remove the 4 pcsfxing thebase andclose to the positioning plate,right

neatly.At the same time,make sureL"guide close to theoutsidecornerofthepaper.Righthandfingershold screws.

3. Same,putonthewhiteprotectoronnewbladebefore

"L"guide at the bottom(as shown), slightly press the "L" the2pcs ofM4X16screws,make sure fasten tightly.

changing.Replace it on bladebase then fasten 4 pcs

3. Remove the white protector,and replace paper

guide let it close to the paper for cutting.

pressure.The C15 blade is now complete. offixingscrew,make sure screws fasten tightly.

Itemno.:Ad-7 Itemno.:Ad-7

How to usethemicropaperguide(Standardand large work desk can be used)

b.Changing the lower blade pad

positioning hole

Too.Bok

ost tion ing axle

There are 2 pcs of positioning axle on the bottom of Fasten the micro paper guide with 2 pcs of M4x50L left/rightmicro paperguide,nstallthe2pcsof screwsby3mmhexwrench.

Turnoff thepower,release thefixed buttonof lower As photo shown,rotate thefeed adjustment in a

positioning axle to fixing positioning hole on work desk.

blade pad counterclockwise. clockwise to the end.

Asshown turnscalebutton,thecounterclockwisemove

To adjust the micro paper guide,first release the

Takescrewdrivertogetbottom-underthelowerblade white-head screwas shown. toforwardandclockwisetobackward.Eachrotation new lower blade pad holeforflxing(as shown),then take pad,forward the pad to scrap box. agridmovementis0.02mm,avaflablemovementis hex wrench align to the guide rand push down until touch total6mmlenght.Once the movement is done,lock- totheend.Thentakethehexwrenchoutandlockthe tightthewhite-headscrew. fixed button of lower blade pad.

Spring replacement for paper pressure

a. Dischange the old spring (P134~P140)

c. Changing the blade base

upper cover 4 pcs screws plastic hook

1. Release the4pcs screws by 2mm hexwrench as 1. Take2pcssmallflat-head screwdriver,insert one

Use finger push and forward the bladebase toscrap box

Attention:Turn off the powerfirst

driver to the small hole,press down the plastic hook arrow shown.

1. Blade base corre sponging to upper blade, Ex: and take thebase out. 2. Hold the adjust button, pull out whole set of safety as shown,and insert another driver to the upper K6bladebase useforK6upperblade.

protector from the outer cover.

K16 blade base use forK16upper blade. 2. Remove thebottom coveris same asupper cover.

2. Take2.5mm hex wrench to loose2 pcs of fixed screws.

Item No.:Ad-7 Itemno.:Ad-7

b.With calibrate gauge

the shaft has corner rounder locating axle

Keep calibrate gauge close to right andleft sideguide. As drawing shown the left cut is too much need to

1. Use small flat-head screwdriver and insert to to 1. If the spring is broken,take out from the shaft Check the relative position between calibrate gauge and adjustleft side guide to right.Drawing2is the perfect smallholeofE-ring,pulloutwardandremovethe directly. rightsideguide,micro adjustment the calibrate gauge cutting after adjustment. 2. lf springisworthless,useonehandholdthelocating E-ring. (Remove one side the shaft has corner to right as red arrow shown.Hold the gauge with right axleandslightlypullopenasarrowshown,another rounder) hand and loosen the2pcsfixedscrewofleftsideguide hand takeout the shaft. by lefthand,thenmove theleftside guide closeto

calibrate gauge and fixed tightly.

cut isgood cut is too Little no need to adjust ofleft slde gulde

As drawing shown left cut istoo little need to move outward

1. Use2.5mm hexwrench release fixing screwsfor 1. Left hand finger insert into the outercover hole

(to left) of left side guide.

spring washer. and push outward the springas shown,right hand hold the spring and puli it outward.(inside the spring still have otherspare parts,do not tilt the outer cover but straighten for easier take the ③Changing blades spring out)

a. Changing the upper blade

ROUND CORNERING MACHINE locating pin

locating pin WARNING

Caution

1. Turn off the power. Caution:V-type blade is sharp, do not touch with fingers.
2. Remove the paper pressure. As shown use left hand two finders hold on bottom of
3. Take2.5mmT-typehexwrench,counterclockwise upper blade, and hold the top with right hand index finger, loosen 4 pcs of fixed screw. slow-shaketoremovethebladeout.

①Constant force spring Same as above take a new blade, aligned and press inward

tothe2locating pinas arrowshown.Take2.5mmT-type hex wrench to look the 4 pcs screw.(Please check again

3 Spring shaft for well looking) ④ Washer For changingR13&R16radlusupperblade,sameworks

aschanging straightbladeC15.Pleasereferpage 10the photo P64, screw tightly with 2 pcs of M4X12 screws.

Item No.: Ad-7 Item No.: Ad-7

b.Spring replacement (P141~P150)

square hole

Put one sheet of paper close toright and left side Check if the corner rounder is tidy or any cutting edge guide.(Keepfinger outof safetyprotector)Step the remain.If yes,make a newlower bladepad cuttingis 1. Push the inner cover to thebottom,referP142for 1. Replace the spring axle and sleeve to the new spring foot switch for cutting testing. requested.How to operate as shown P50-P51. correct direction.As right photo shown the outer centerhole,pleaserefer above photo 2toinstall (When the upper blade torise up,if heard a sharp the spring for right direction. cover shaft hole is on upper direction. noise.Canbeadd a little lubricating oil on upper 2. Replace thespring washer into the square hole as blade'sflank thendried toresolve thenoise.)

arrowindicated.(donotput the spring was her at the reverse side.) spring prominent slde spring washer hole

1. Release the fixed button of lower blade pad counter- Turn counterclockwise one section of feed adjustment as shown, the lower blade pad will move 0.125mm.(one time clockwise. 1. Tuntheoutercovertofrontside,driventhespring 1. Left hand hold the outer cover,right hand take the one section can get better incision)Then lock thefixed
2. Fixed button can be pulled out and tum around to from the top andmakes spring washer hole meet the ready new spring set andinstall toinner cover.Be buttonand try cuttingagain,if the situation remains the change position.Adjusted to thebest position between careful keep the spring prominent side at theleft. outer coverhole. same,pleaserepeatP50-P51.(alowerblade padcan be scrap box and tool box. 2. Be carefull the spring fixed gasket fall down, and 2. Replace thefixing screw and fasten tightly. use 80sections) 3. To lock,hold the handle while rotating clockwise and prevent the spring sleeve and axle exposed from inward to press. spring setfor proper installation.

②Right and left side guide adjustment a.Without calibrate gauge top of the outer cover retafnlng ring plfers outer covershaft hole pad block cut fs good no need to adjust cutis too much need to move inward

three reference lines D01 1. Remove theinner cover to the top,insert the spring 1. Find a pad block put on the inner cover(4mm above Above shown the right side cutisgood no needto Release2fixed screwonleftsideguide.Referthethreelines axle a litter as shown direction.(contrary insert is thickness) as arrow shown.

prohibit) 2. Use retaining ring pliers to insert the 2 small holes

onworkdesk,arrowis the direction of inward movement, adjust. Left side cut is too much need to move inward ofleft side guide. keepfront edge of theleftside guide and reference line are parallel thenfixed it for once cutting. cover,pullthe spring let shaft pass through thehole

and hold the spring until the shaft go through to

If the situation remains the same,please repeat above pro-

anotherside shaft hole.

cedures unit get perfect corner rounder.

Itemno.:Ad-7

Item No.:Ad-7

long nose plier natural state on the shaft Upper blade shaft groove Lower blade pad

1. Take theremoved E-ringhook onto the shaft groove 1. lefthand hold the outer cover,andright hand hold as shown,and replace it by long-nose plier. thelocating axleand slightly pull the spring see if

2. Becareful hanging thespring natural state on works up and down smoothly.

2. If cannotmove,need to dischargeandre-assembly the shaft,do nothook thespring on shaft groove. Abovefigure show the ready position for right and left (Attention:Make surethe correct voltage) and test again.

side guide. Plug foot switch cord①into the socket,then power cord 2 into the socket.

adjust button imum clearance

1. Finally,install the safety protector and tighten the

1. Packback theblackrubberbottomcoverbyflat-head 3/8" 4screws. screwdriver and push close tightly.

2. As above and then loaded upper cover.

1. Pull forward torelease thepaper pressure from Loosen the adjust button of safetyprotector,moveit down to thebottom andlockit.

Keep the safety protector and work deskminimum

2. Hold the paper pressure,will be two positioning pins

G. Maintenance clearance3/8". into thetwoholes,upward push to the top and then

release thequick-releasebuttonfor auto-lockpaper

Changing fuse and discharge capacitor pressure.

Emergency stop

Foot switch

Power switch

Before disassemblythe circuit,usermustto discharge the

Replace thefuse

1. Unplug the power cord. capacitor'ssurpluselectricty.Andpayattentfonfingersdo

1. Turn on the power switch motor is standby, the light 1. Tum the operation mode to auto.(for manual mode,

2. Takeflat-head screwdriver,pry-open the holeas notto touch the metal part when using the screwdriver.

leave the upperblade slightly off the top position,

1. Usetheflat-head screwdriver pry open thecoverof the isonbut motor notrotation. picture shown outward,pull out the fuse holder by
2. Turn the operation mode to manual. andstep on thefoot switchto start)

another hand. terminal blocks.

3. Push-down manual start button,push-down to start 2. Testwith thefoot switch seeif normal operation.

3. Remove the damagedfuse andreplace a new one 2. Use the cross-head screwdriver to hold the M5 junction

(push-down the switch to finishing a cycle,release release to stop motor,make upper blade slowly down

that meetthespecification,thenre-plugthepower of the screw,and useflat-head screwdriver to hold the cord for using. the foot switch then start again) M6junction of thescrew,thenmoveboth screwdriver

ready for working.(blade hasbeen calibrate by original)

to touch.At same moment will have sparkles caused from the touch.

3. After disassembly,replace the cover of the terminal blocks.

Item No.: Ad-7

Item No.: Ad-7

F. Machine operation 2Lubrication applying(Refuel lubricant every 30 days for using frequently. CAUTIoN: Before operating machine, carefully read all the manual ① Installation and cutting test Quick-release button

gear protector cover

Qufck-release devlce

P77~P80showhow to lubricate themain strueture. Asshown smeara little grease lubricant onbevelgear,

1. Tun off power, unplug the power cord.
2. Removethe10pcsscrewofoutsidetheshield,both fixing screws andfasten tightly.

Place machine on topof a sturdy work table. 1. Pullforward to release the paper pressure from hands hold the shield and move upward slowly. quick-release button. 3. As shown remove the2 pcsscrew on gear protector cover. 2. Hold the paper pressure, downward to the end and 4. Move the gear protector upward slowly. pull out the paper pressure,then release the quick- release button. 2.5mm hex wrench 12 mounting holes

Asshownisthelubricatinglinearslider(2sliderseach Asshownisthecamtrackforlubrication,takefew

Place the work desk onto themachine as shown. Take the2.5mmhexwrench,fasten the12pcsflat-head left and right), carefully press a little grease lubricant lubricant byflat-headscrewdriver and spread lubricant Align themachine screw holesto the 12mounting holes hex screw(size: M4x8). by grease nozzle into the sliders. onboth sides of cam track. as arrows indicate. 2 holes for right side guide right side gulde forright sidegulde 3mm hex wrench reference line P82 P81~P82 show how to lubricate the paper pressure. Takefewlubricantbyflat-headscrewdriver,spreadto P40 First,discharge the paper pressure. Place front edge of the right side gu fde on the central As arrowshown the2holes areforright side guide 1. Counterclockwiserotationthewhite-ball.

2. Take2mm hexwrench torelease the2pcsfixing

hole. referenceline,targetthe2-hole showninP40onthe 2shown the reference line for the right side guide fixed holes. screwswhich under white-ball, then remove the cover.

3. As shown apply alittle lubricant on the whole activities

place and adjust the reference. Use3mm hexwrench lock theM4x12socket-headhexscrew. Fixed left side guide same as above. parts.

4. Reinstall the cover and thewhite-ball.

Item No.: Ad-7 Itemno.:Ad-7

D. Standard parts & accessories (total 8 parts)

Left and right side gufde Maintenance tools: Standard work desk -1 pc Tool and scrap box - each

1. Cross-head and flat-head each 1pc 1 pc screwdriver-each1pc
2. T-type hex wrench (2.5,3) each'1pc
3. Hex wrench(1.5/2/2.5/3/4)
4. Fuse (7A) - 5 pcs

system. with a little lubrication while rotating.

1. Discharge the paper pressure.
2. Remove the left and right side guide and work desk.
3. Lubricate the movement blade pad feeding device.

1.1/4upperblade-1 pc Maintenance screw set Paper pressure - 1 set Operationalmanual-1book

1. Round-head hex screw(M4x8) - 5 pcs 2.1/4" lower blade pad-10 pcs

2. Flat-head hex screw(M4X8)-10 pcs 3. 1/4" blade base -1 set

3. Truss-head cross screw(M4X8)-5pcs

4. Socket-head hex screw(M4X12) - 4 pcs

5. Washers (@4X2t) · 4 pcs

E. Optional parts & accessories (total 13 parts)

As shown when the scrap box accumulated up to seven P26 P27 full please empty the scrap,in order to prevent therisk Large work desk Straight blade L guide Straight blade base when upper blade work down cutting. Size: 19.7(w)x 11.8"(L) Size:5/8"

③ Blade sharpened (K3.5/K6/K10 upper blades and straight blade are all available to sharpen by oil stone)

Upperblade Lower blade pad Half moon blade

Micropaper guide set

Calibrate gauge Constant force spring Half moon blade regulator

Bladeis sharp,do not touch withfinger. As shown put radiusV-shaped blade on the oil stone. Add a little lubricate on the oil stone,smoothmoves back and forth sharpened blade. For straightblade,same operation asradius blade. Forhalf moonbladeandK13&K16upperblades,sharpen by machine is recommand. Oilstone

Itemno.:Ad-7

H.Electronic control system (110v) ① Electrical drawing 2Position chart

KM1 12

SA22 POWER REVERSE AUT ENG STDP DN-DFF SA2 SA1 SB2

Sa1-2 Sb1 Sq1 No

Sa21 Nc Nc 13

Spindle

15 KT1 ND

Manual Manual

Valve

Air Start

Spindle

Ka1 Spindle

On Stop

Sa1 Av-110V Time

Monuol start/Reverse VE 15 Brake limit switch Indicotor lomy KA1 KA2] KT1 KM1

Foot switch ANY-2 MY 2 -NJ MY2-NJ

Sb2 L Y4-Nj L Y4-Nj

12 10 12 M6 M6 11 14 13 14 13

Q2 11 Time

5628910UM6VM5

Motor

Motor M6 Ms

Motor

WIRE-0.75mm²+3C BRAKE XS2

Iph 110Vac 50/60Hz Power Motor Xs1

Power Supply Ac-110V

Itemno.:Ad-7

I. Diagram and parts list After service will request below information: 1. Modelnumber

2. Machine serial number (marked behind on machine)

①Machinemain structure 3. Parts number, name and quanty

(28)(29) 30) (31)(32

Wereserves theright tochange the design

Item No.: Ad-7

Parts list

No. Q'ty Diagram no. 'ON Diagram no. Q'ty Description Description Control parts plate D14-01 Power socket 36 37 D14-04 Foot switch socket Right front plate 38 End cover limits switch Back plate D03-03 39 Left front plate D14-03 Right back fixing plate D03-04 40 D02-05 Left back fixing plate Right side guide Left side guide D02-04 Calibrate gauge 42 D02-06 Outside the shield D13-02 Large relay Lguide D02-07 43 Gear protector cover D04-08 44 D15-01 Standard work desk Small relay 45 D02-02 Back pad 46 Front pad D02-03 11 D04-02 Relay base Lower blade system 12 47 Followedby details Brake limits switch 13 LS fixing plate D04-01 48 Back structural plate D05-03 Inner shutter 14 D04-03 49 Motor base Middle structural plate D05-02 Main shaft system Followed by details Main structural 16 Front structural plate D02-01-1 51 Left scrap plate 17 D01-03 52 Main base D01-01 18 D01-02 53 D01-06 Upper scrap plate Adjustable leg-glides 19 Middle scrap plate Adjustable nut D01-08 D01-05 55 Left cover 20 Right scrap plate D01-04 D03-02

D14-10 D07-11

21 56 Magnet seat Middle fixing axle 22 D14-07 Back shutter D01-10 Lower fixing axle 23 Tool box 58 (200W) D04-06 Motor 24 D04-07 59 LG washer Terminal blocks seat D04-09 Terminal blocks 25 Linear guideway 60 Paper pressure system Relay guide seat D04-10 26 Followed by details 61 CF upper guide D07-13 Rectifier 27 62 28 D07-14 Earth copper plate 63 CF lower guide 29 64 D04-05 Main slide seat D07-01 Scrap box 30 Reinforcement axle Limiting board D07-15 65 D14-09 31 D14-06 Upper fixing axle 66 Right cover 32 Blade base Upper blade (R6) D07-08 67 Power switch Emergency stop switch 33 68 34 Function switch 35 Manual start switch "#" Standard hardware parts

Item No.: Ad-7

After service will request below fn formation:

2Parts of structure:Main shaft system and Lower blade system 1. Model number

2. Machine serial number (marked behind on machine)
3. Parts number,name and quantity

Main shaft system Lower blade system

Wereserves the right to change thedesign

Item No.: Ad-7

Parts list

No. Q'ty Diagram no. 'ON Q'ty Description Diagram no. Description Main shaft Cam 69 D06-06 104 Angular contact ball bearing D05-04 70 105 Baseboard (7206) Main shaft seat Bladebase D07-06 106 D05-13 71 (R6) Thrust bearing 72 Setscrew 107 (51106) (M4X10L) 73 Fixing nut Blade fastening plate D07-10 108 D05-18 Controlring D07-09 109 Setscrew 74 (M4X6L) 75 Large bevel gear D07-16 Small bevel gear D07-18

Washer D07-20 Cam followers (CFH10) 80 Lower blade pad D05-08 (R6) 81 Left fastening plate D06-01 82 Setscrew (M3X6L) 83 D06-16 Cam washer 84 Cam baseboard D06-03 Left outer plate 85 D06-04 86 Setscrew (M3X10L) Return spring D06-10-1 Baseboard D06-05 89 Right outer plate D06-04 06 Locking handle D06-15 91 (M6) 92 Cam shaft D06-09 93 Push plate D06-12 Feed base D06-11 Positioning plate D06-14 96 D06-17 97 D06-13 Feed shaft

66 Feed knob Steel ball (03) Spring MP-19 102 Right fastening plate D06-02 Shrink-ring D06-07 "# Standard hardware parts

Item No: Ad-7

After service will request below information:

1. Model number
2. Machine serial number(markedbehindonmachine)
3. Partsnumber,name andquantity

Paper pressure system Micro adjustment paper guide system

Were serves the right to change the design

Item No.: Ad-7 Item No.: Ad-7

B. Safety instructions (Before setting up the machine, carefully read all the manual) Parts list

No. Q'ty Diagram no. No. Diagram no. Description Description

Make sure the outlet with the correct volgate and type Washer D10-09 D12-12 110 Right side plate 145 Blade is sharp, non-operator please keep away from machine. Quick-release button D10-17 146 Fixing seat D12-10 111

112 D10-10 Upper plate Micro adjustments crew D12-06 147

Do not put fingers into the safety protector during operating time. Sleeve 113 D10-21 D12-07 148 Front adjusting nut

Back adjusting nut 114 Fixing plate D10-24 D12-08

Do not cut staples, paper clips and other metal objects.

Scale ring D12-09

Silencing pad D10-25 150

Always turn off power when changing blade. D10-16 Spring shaft 116

117 Upper cover D10-14

Always turn off power when work completed.

Constant force spring D10-19 119 Hanging spring shaft

C.All kinds of blade

120 Slide block

① Upper blades (5 radius upper blades, 1 straight blade, 1 half moon blade, total 7 kinds)

Slideway D16-02

Safety protector 124 adjust button 125 Location axle 126 Rubber gasket 127 D10-13 Lowercover

AD7-K3.5 AD7-K6 D10-01 Outer cover 128 Upper blade Upper blade Upper blade Upperblade

Size:R1/8" Size:R1/4" Size:R3/8" Size:R1/2" 129 E-ring (E4)

130 Setscrew 131 D10-02 Inner cover

133 Locating axle

Slide shaft D10-18

AD7-K16 AD7-C15 AD7-D21 Locking spring 136 D06-10-2 Straight blade Upperblade Half moonblade

Size:R5/8" D10-05 137 Inner plate

2Lower blade pads (straight and half moon blades can be with any kinds of lower blade pad) D10-08 138 Left side plate

139 Main plate 140 Setscrew

142 Panel board D12-02-2 (R) 143 (R) D12-01-2 Guideway shaft D12-11

Ad7-K3.5-2 Ad7-K6-2 Ad7-K10-2 Ad7-K13-2 Ad7-K16-2

Lower blade pad Lower blade pad Lower blade pad Lower blade pad Lower blade pad

"#Standardhardware parts

Size:R1/8" Size:R5/8" Size:R1/4" Size:R3/8" Size:R1/2"

Item No.: Ad-7

Item No.:Ad-7

4 Screws and other standard hardware parts list A. Name of machine parts No. Specifications Q'ty No. Specifications Qty Hardware description Hardware description 41 Hex socket head screws Hex flat head screws M3X10L Hex button head screws 04X2t Quick-releasebutton 44 12 M4X8L Hex flat head screws M4X8L Hex button head screws Auto/Manualselectbutton Power switch

Emergency stop

45 Hex flat head screws M3X10L Hex socket head screws Reverse/Manual start select button M4X6L Hex flat head screws Hex socket head screws M3X10L Outside the shield Hex socket head screws Hex socket head screws M4X12L M4X6L

Paper pressure

49 Front plate Hex socket head screws Hex flat head screws M4X8L 10 M4X6L Hex socket head screws Hex socket head screws M4X8L 50 M4X12L

Adjust button for

Hex socket head screws Hex socket head screws M4X8L 51 M4X12L 11 safety protector Cross round head screws 12 54 M3X16L 08x2t

Left side guide

13 Hex flat head screws Hex socket head screws M4X6L 10 55 M4X8L Hex flat head screws Hex socket head screws 57 14 M6X20L M4X8L

Right side guide

Hex socket head screws Washers 06X2t 58 M8X25L

Hex nuts 08x2t Safety protector Lower blade pad

Hex nuts

16 Hex socket head screws M5X10L M8 Location pins 05x10L Cross round head screws 59 17 M4X8L M4X10L Cross round head screws Hex socket head screws 18 Hex socket head screws 61 Hex socket head screws M4X8L M4X8L

Standard work desk (12.6"X11.8")

Hex socket head screws 19 M4X8L 62 Cross round head screws M4X12L Cross round head screws 63 20 M4X8L Hex socket head screws

M4X12L M4X12L 65

21 Hex socket head screws Hex socket head screws 22 M4X8L M4X12L Hex socket head screws Hex sockethead screws 25 66 Hex flat head screws Hex socket head screws M5X25L M3X10L Hex socket head screws Hex button head screws 27 M5X12L M4X8L Angular contact ball bearing

Location pins 05X16L 70 Upper blade

Hex socket head screws 28 Hex socket head screws M5X12L 71 M5X12L Location pins Location pins 05X16L 04X10L

Machine serial number

Thrust bearing 51106 29 72 Hex socket head screws Hex socket head screws 74 M3X8L 30 Hex socket head screws M4X12L Hex headless screws 31 Hex socket head screws 75 M5X8L Hex socket head screws 5X20L 32 M4X20L Square keys Hex socket head screws Location pins 03X10L 76 M5X8L Scrapbox Square keys Hex flat head screws 36 M4X8L 5X20L 37 Hex flat head screws Cam followers CFH10 79 M4X8L Hex socket head screws M3X8L M3X20L 81 38 Cross round head screws Hex nuts M3 Location pins 03X10L Fixed buttonfor lower blade pad Tool box Power socket Hex socket head screws Hex flat head screws M3X12L 39 M4X8L 85

Feed adjustment for lower blade pad Foot switch socket

Hex socket head screws Hex socket head screws 40 M4X16L M4X8L Hex socket head screws Washers 04X2t M4X12L

Table Ofcontents Item No.: Ad-7 Item No.: Ad-7

A. Name of machine parts ....

No. Specifications Q'ty Hardware description No. Specifications| Q'ty Hardware description

B. Safety instructions ...

85 Location pins

C. All kinds of blade 05X12L Location pins ① Upper blades.... Hex socket head screws M3X12L 89 2 Lower blade pads Hex socket head screws M4X8L

Hex socket head screws M4X12L

D. Standard parts & accessories

Location pins 03X12L

E. Optional parts & accessories

Location pins 05X12L

F. Machine operation Location pins 93 05X28L ① Installation and cutting test ... 94 Hex socket head screws M4X28L

Location pins 05X10L

2Rightand left side guide adjustment

Steel bal1 03

a. Without calibrate gauge ....

Hex socket head screws 102 M3X8L

b. With calibrate gauge ....

Location pins 03X10L

③ Changing blades

105 M4X10L Hex socket head screws

a. Changing the upper blade ....

106 Hex flat head screws

b. Changing the lower blade pad

108 M4X6L

C. Changing the blade base Hexflat head screws

d. Changing the half moon blade D21 Location pins 04X6L

e. Changing the straight blade C15 M4X12L 110 Hex socket head screws

112 M3X6L Hex flat head screws

④ How to adjust the D21 regulator .... 11

114 Hexflathead screws M3X5.5L

How to use the "L" guide .... 11

Hex flat head screws 118 M4X34L

6 How to use the micro paper guide 12 E-ring 119 04 Spring replacement for paper pressure M3X3.8L 121 Hex flat head screws

a. Dischange the old spring M3X6L 132 Hex flat head screws

b. Spring replacement ... 14 M4X10L 133 Hex flat head screws G.Maintenance Hex socket head screws 134 M4X8L ①Changing fuse and discharge capacitor Hex socket head screws 137 ② Lubrication applying Hex socket head screws

Hex socket head screws M4X29L

③ Blade sharpened ... 17

139 M5X16L Hex socket head screws

H. Electronic control system M4X10L Hex flat head screws 142 ① Electrical drawing... 18 143 Hex socket head screws M4X50L ②Position chart ... Hex socket head screws 146 M3X8L

149 Hex socket head screws

I. Diagram and parts list

150 Hex headless screws

① Machine main structure 19 2 Parts of structure: Main shaft system and Lower blade system .. 3Parts of structure: Paper pressure system and Micro adjustment'paperguidesystem... 4Screws and other standard hardware parts list.....

Electric Corner Rounding Machine

Specifications

Item No. AD-7

Operational Manual

Seven Kinds 1/2" 5/8" 3/8" of Blades Half Moon diameter 13/16" Straight length 5/8" Cutting Capacity 27.56"(700 sheets) Cutting Speed 46 rpm Dimensions 24.6"(W) X 12.6"(D) X 17.5"(H) Weight / Volumn 110 lbs / 3.14 CbFt

Power 110vac (50~60Hz)

Motor 200 W

Item No.: Ad-7