Text on page 1
Akiles iCoil Spiral Coil Binding Machine
Instruction Manual
For Models: iCoil 41 Round Hole iCoil 41 Plus Oval Hole
Page 1 of 3
Text on page 2
iCoil OPERATIONAL MANUAL
Introduction
Punchandbindingmachineforcoilbinding.Yourciwasdesignedwith
A FULL RANGE OF FUNCTIONS AND PREMIUM QUALITY COMPONENTS TO GUARANTEE AN
Effortlessandprofessionalbindaswellasmanyyearsoftrouble-Freeservice
Important
WERE COMMEND THAT YOU TAKE A FEW MINUTES TO FAMILIARIZE YOURSELF WITH THE FUNCTIONS OF
ACHIEVE PROFESSIONAL RESULTS.
Features
Punch Handle
Side Margin Control
Manual
Coil size Selector Diameter Scale Coil Crimper
Electric Roller WasteDrawer
Assembly
- PlaceyournewCllon topofa sturdy
- Remove the screw from punch axle punch handle in a vertical position on to the &install footpedal by plugging the cord into thebackof themachine.
Caution
Page 2 of 3
Text on page 3
Coil BINDING
Set-Upintructions (Steps 1-3)
1)Basedondocumentthicknessyoumustfirstdetermine Diameter Scale andSelector
OPEN the Roller
your full unbound document into the Diameter Scale.
See picture 1
- Based ondocument length,you must nowadjust the Side Margin Control side margin for an evenly centered punch. To do so, press and slide Side Margin Control.See Picture 3.
Hint:Werecommendforyoutotestpunchsomewaste Letter SizePaper
paper and readjust the Side Margin Control as needed.
Punching&Inserting(Steps4-7)
- Insert sheets into the punch throat and pull handle
slid against the side margin.
5) Insert pre-selected coil into first 3-4 holes. See picture 5
a) Makesure all holes are evenly aligned. b)Usebothhandstofirmlyholdleft and rightsideof document asclose as possible to punched holes.
c) Press foot pedal first, then gently bring document parallel to roller until coil touches the roller. Donot apply excess pressure as this may distort the coil pitch and coil insertion may become more difficult.
toward theoperator.Seepicture7
Technical Information
Coil 4:1 Capacity&Diameter
Size 4mm Round hole Ovalhole
No.Sheets DOCUMENT COIL (20 Ibs) inch mm mm 35 5/32" 6mm
11"=43Holes 11"=44Holes 45 4.8mm 7mm 3/16" 8.5"=34 Holes 8.5"=34Holes Binding 6.4mm 60 8mm 1/4" Format 70 7.2mm 9/32" A4 =46 Holes A4=46 Holes
80 5/16" 100 12mm 13/32"10.3mm 120 15/32"11.9mm 150 19/32" 15.0mm 19.0mm 20mm 200 25/32"19.8mm
WarRANTY POLICY
Yourclhasawarrantyofoneyear Fromdateofpurchase.In The Eventofa
MANUFACTURER'SDEFECT,YOURDISTRIBUTOR(ATOPTION)WILLREPAIRORREPLACEIT.
Treatmentoftheunit,Includinganyextraordinaryeventleadingtothedamageof
THEMACHINE,WHETHERITISREVERSIBLEORNOT.
Haveyourmachine'Sserialnumberandthepurchasedateready.Ifthemachinemust
It,Asanydamagesincurredduringitstransportationarenotcoveredbyour
WARRANTY POLICY.
Page 3 of 3 · End of manual
Quick start
- Assemble: Put the machine on a sturdy table. Remove the screw from the punch axle and fit the punch handle vertically. Plug the foot pedal cord into the back of the machine.
- Pick coil size: Put your full unbound document into the Diameter Scale to find the coil size. Set the Coil Size Selector to match.
- Set the side margin: Press and slide the Side Margin Control so the punch is centered. Test punch some waste paper first.
- Punch: Insert the sheets into the punch throat and pull the handle.
- Start the coil: Insert the chosen coil into the first 3 to 4 holes. Make sure all holes are evenly aligned.
- Feed the coil: Hold the document firmly on both sides near the holes. Press the foot pedal first, then gently bring the document parallel to the roller until the coil touches it.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Coil is hard to insert or the coil pitch is distorted | Too much pressure was applied against the roller. | Do not apply excess pressure. Gently bring the document parallel to the roller. Page 3 |
| Punch is not centered on the page | The Side Margin Control is not set right. | Press and slide the Side Margin Control. Test punch waste paper and readjust as needed. Page 3 |
| Coil does not start | Holes are not evenly aligned. | Make sure all holes are evenly aligned and hold both sides of the document close to the punched holes. Page 3 |
| Wrong coil size | The size was not matched to the document thickness. | Use the Diameter Scale and the Coil Size Selector with the full unbound document. Page 3 |
| Machine is not working properly | Unknown fault. | Contact your dealer. Have the serial number and purchase date ready. Page 3 |
Frequently asked questions
Which iCoil models does this manual cover?
The iCoil 41 Round Hole and the iCoil 41 Plus Oval Hole. See page 1.
How do I choose the coil size?
Put your full unbound document into the Diameter Scale, then set the Coil Size Selector. See page 3.
How many holes does the iCoil punch on letter size paper?
11 inch length is 43 holes for round and 44 for oval. 8.5 inch length is 34 holes. See page 3.
How do I center the punch?
Press and slide the Side Margin Control. Test punch waste paper first and readjust as needed. See page 3.
What is the warranty?
The warranty is one year from the date of purchase. See page 3.
