Akiles Pro-Lam Ultra Six Roller Photo Laminator Operation Manual, page 1

Page 1 of 9

Akiles Pro-Lam Ultra Six Roller Photo Laminator Operation Manual, page 2
Text on page 2

ProLam ULTRA

6 Roller Photo Pouch Laminator

Professional Grade

Operation Manual

Make sure you read this manual before using the machine. Store this guide safely, so that you can use it in the future.

Page 2 of 9

Akiles Pro-Lam Ultra Six Roller Photo Laminator Operation Manual, page 3
Text on page 3

Contents

1. Specifications............................................................ 1

2. Safety Precautions................................................. 2-3

3. Lamination Settings Guide....................................... 4

4. Control Layout & Functions..................................... 4

5. Operating Instructions........................................... 5-6

6. Troubleshooting......................................................... 7

7. Warranty Policy.......................................................... 7

1. Specifications

14 mil (350 mic)

Heated Rollers Internal Heating

110-120V or 220-240V (Check label on unit)

Page 3 of 9

Akiles Pro-Lam Ultra Six Roller Photo Laminator Operation Manual, page 4
Text on page 4
  1. Safety Precautions

WARNING

Do not use broken, aging or self-made electrical wire. Do not bend, twist or tie the electrical wire, to avoid the fire or electric shock.

If the power cord is damaged, it must be replaced by the manufacturer or our service agent or a similar qualified technician.

Do not use a power outlet outlet that is not in accordance with the rated voltage, to avoid the risk of fire or electric shock.

Do not disassemble, modify or repair the machine yourself.

DO NOT

DISASSEMBLE

Do not wear neckties or necklaces while operating this machine.

ENTANGLEMENT

WARNING

If an article becomes stuck in the machine, press the REVERSE button right away. If this does not work, cut off the power supply at once.

Do not open the cover of the machine.

Do not operate the machine with the cover open.

Do not introduce the machine to water.

ELECTRIC SHOCK

WARNING

Do not operate the machine with wet hands.

Unplug the machine from the power supply when moving.

Do not put on top of the laminator while it is in use.

Do not insert objects other than laminating pouches, as they may burn and give rise to smoke.

HIGH TEMPERATURE

WARNING

Do not touch the cover, rubber rollers or heating part while the machine is in use.

Page 4 of 9

Akiles Pro-Lam Ultra Six Roller Photo Laminator Operation Manual, page 5
Text on page 5
  1. Safety Precautions

WARNING

Keep this machine in a dry and cool place.

WORK AREA

POUCH FILM

OBJECTS

Make sure the machine has room in front of and behind the machine for adequate airflow and to allow sufficient space for the laminating pouches to go in and out.

This machines has been tested to be 100% compatible with Akiles brand laminating pouches. Using other brands may not achieve the same results.

The length and width of the laminating pouch should be 3-5mm larger than the document to be laminated.

The ProLam Ultra uses heated rollers, so do not use the following objects with this machine:

  • Easy to burn material
  • Documents wider than 13”
  • Documents thicker than 1mm
  • Single side pouch films (PVC film)
  • Heat sensitive paper or articles that can be faded or transformed by heat
  • Articles that have cracks, dampness, or deformation before laminating
  • Coins or any other types of hard material

MACHINE

OPERATION

Please follow the recommended heat settings in this manual when using this laminator.

Turn off the machine when it will not be in use for an extended period of time.

If you have issues with the machine, please discontinue use and contact your dealer for repair.

NOTES

Close supervision is necessary when using this machine near children.

Do not use any accessory that is not designed specifically for this machine.

Laminated photos, documents, etc. are permanent and cannot be taken apart.

Page 5 of 9

Akiles Pro-Lam Ultra Six Roller Photo Laminator Operation Manual, page 6
Text on page 6
  1. Lamination Settings Guide

Film Thickness (mil)

  • If using a low temperature film, please decrease temp 15 - 20°C.
  • To avoid damaging the machine, please use recommended settings.
  1. Control Layout and Functions
  • Start: Hold HOT 1 sec
  • Off: MEMO, STOP
  • Memory: MEMO, 1~7
  • Cold: MEMO, HOT
  • HOT / COLD

: Start Hot / Cold Lamination

  • TEMP

: Modify temperature (0~140°C)

  • SPEED

: 1 ~ 9 Speeds

  • MEMO

: Preset temp and speed settings (MEMO + 1~7)

  • MEAS

: Display current roller temp.

  • STOP

: Stop roller operation

  • REVERSE

Page 6 of 9

Akiles Pro-Lam Ultra Six Roller Photo Laminator Operation Manual, page 7
Text on page 7

5. Operating Instructions

1. Plug the included power cord into the back of the machine and into a compatible power outlet.

2. Turn on the power switch behind machine

  • Hold the HOT / COLD button for 1 second and the LCD display will turn on.
  • Hot mode icon will flash.
  • The initial setting is at 100°C and Speed 6
  • When the machine has warmed up to the set temperature, the “READY” icon

will show on the dispaly and the machine will beep 3 times.

  • To increase or decrease the temperature, use the UP or DOWN Temp buttons.
  • To laminate faster, use the UP or DOWN Speed Buttons (1~9 Speeds)
  • To see the current roller temperature, press MEAS.
  • To stop the rollers press STOP.
  • To put the rollers in reverse, press REV.
  • To use the factory preset settings, press MEMO, 1~7.

Memo+1: 100°C, Speed 7

Memo+5: 115°C, Speed 5

Memo+2: 100°C, Speed 6

Memo+6: 120°C, Speed 4

Memo+3: 105°C, Speed 6

Memo+7: 130°C, Speed 4

Memo+4: 110°C, Speed 5

Warning - Insert the sealed side of a laminating pouch first.

  • Hold the HOT / COLD button to turn on the LCD display.
  • Press MEMO button and then press the HOT / COLD button.
  • The display will read Cold and the cold mode icon will flash.
  • When the “READY” icon shows on the display, the machine will beep once

and the user can start laminating. (Use cold film only).

Page 7 of 9

Akiles Pro-Lam Ultra Six Roller Photo Laminator Operation Manual, page 8
Text on page 8
  1. Operating Instructions
  • Press MEMO and then the STOP button to initiate AUTO SHUTOFF.
  • Once the roller temperature reaches below 65°C, the machine will beep

5 times and the power will shut off automatically.

  • (Keep the temperature at 70°C and speed 2 for “STAND BY” mode.)

Warning - Do not turn off the Power Switch as soon as you are

finished laminating to prevent overheating. Please use the AUTO

SHUTOFF feature to prevent overheating.

Page 8 of 9

Akiles Pro-Lam Ultra Six Roller Photo Laminator Operation Manual, page 9
Text on page 9
  1. Troubleshooting

Machine has no power or the rollers are not turning

  • Power cord is not properly
  • Make sure the power cord is
  • Power switch is off
  • Check that the power switch
  • Temperature is not at the
  • Adjust the temperature
  • Operation of the gears is
  • Turn off the machine and

No increase in temperature

  • Check power plug
  • Turn off the machine and

Corner is not sealed

  • Document is too thick or
  • Use a thinner document,
  • Something may be stuck
  • Turn off the machine and

the temperature setting is not hot enough

between the rollers or they are out of position

is in the on position

higher or lower until the desired result is achieved

leave approx 5mm of space around the edges, and/or turn up the temp setting

  1. Warranty Policy

Your ProLam Ultra has a warranty of one year from the date of purchase. In the event of a manufacturer’s defect, your distributor (at option) will repair or replace it. IMPORTANT: This warranty does not cover damages due to improper use or mistreatment of the unit, including any extraordinary event leading to the damage of the machine, whether it is reversible or not.

Page 9 of 9 ยท End of manual

Quick start

  1. Plug the power cord into the back of the machine and a compatible outlet, then turn on the rear power switch.
  2. Hold HOT/COLD for 1 second; the machine starts at 100°C and speed 6.
  3. Adjust temperature and speed with the UP/DOWN buttons, or press MEMO + 1–7 for a preset.
  4. Wait for the READY icon and 3 beeps.
  5. Use a pouch 3–5 mm larger than the document and insert the sealed side first.
  6. For cold film, press MEMO then HOT/COLD and wait for READY.
  7. When finished, press MEMO then STOP for auto shutoff; don't switch the power off right away.

Troubleshooting

ProblemLikely causeFix (from the manual)
No power or rollers not turningPower cord not properly connected or power switch offMake sure the power cord is plugged in and the power switch is on. Page 9
Poor results at current settingTemperature is not at the right settingAdjust the temperature higher or lower until you get the desired result. Page 9
Corner is not sealedDocument too thick or temperature not hot enoughUse a thinner document, leave about 5 mm around the edges, and/or turn up the temperature. Page 9
Rollers or gears not operating correctlySomething stuck between the rollers or rollers out of positionTurn off the machine. Page 9
An item gets stuck in the machineEntanglementPress REVERSE right away; if that fails, cut the power at once. Page 4

Frequently asked questions

What pouch thickness can the ProLam Ultra laminate?

Up to 14 mil (350 mic). Documents wider than 13" or thicker than 1 mm should not be used. See page 3 and page 5.

What are the memory presets?

MEMO+1: 100°C/speed 7, +2: 100°C/6, +3: 105°C/6, +4: 110°C/5, +5: 115°C/5, +6: 120°C/4, +7: 130°C/4. See page 7.

Can it do cold lamination?

Yes. Press MEMO and then HOT/COLD; use cold film only. See page 7.

How do I turn it off properly?

Press MEMO then STOP. It shuts off automatically once the rollers cool below 65°C. See page 8.

What is the warranty?

One year from the date of purchase against manufacturer's defects. See page 9.