Page 1 of 2
Text on page 2
OPERATION INSTRUCTIONS
Congratulations on the purchase of your new . A professional and efficient hand operated rotary trimmer. Your was carefully designed with self-sharpening tungsten steel blade and premium quality components to guarantee an effortless and professional trimming, as well as many years of trouble free service. We recommend that you take a few minutes to familiarize yourself with the functions of your . You will find that with just a little practice, anyone can achieve professional results.
F E AT URES
Blade Carriage ( Rotary Blade Inside )
Work Table with Grid Ruler
Depth Guide ( Adjustable )
OPER AT I O N
- Place your on a sturdy table.
- Position the Blade Carriage at either end of Sliding Poles. REMARKS: Your is designed to trim in either direction.
- Using the Ruler Guide, adjust the Depth Guide to the desired measurement.
- Insert trimming material beneath the Clamping Bar and align it against the Ruler Guide and Depth Guide.
- Hold trimming material while sliding the Blade Carriage to complete the trim in one movement. REMARKS: Do NOT place or press your fingers on the Clamping Bar while trimming, to avoid injury.
IMPORTANT:
Your can trim a very wide range of materials, such as paper, newsprint, cardboard, plastic films, polycover, vellum, aluminum foil, vinyl, PVC, polyester, polypropylene, polyethylene, leather, veneer, etc. The trimming capacity of your is up to 2.0 mm. To maximize the lifespan of your , never exceed the trimming capacity (2.0mm) and always adjust the sheets of trimming material according to the material being trimmed, so that you can comfortably slide the Blade Carriage.
SAFETY
& MAINTENANCE
- Always carry or pull your by the baseboard. NEVER carry it by the twin poles.
- NEVER place your fingers underneath the Blade Carriage, to avoid injury, as blade is inside the carriage.
- NEVER touch the table blade to avoid injury.
- Do NOT place or press your fingers on the Clamping Bar while trimming, to avoid injury.
- The rotary blade is designed to self-sharpen. Slide the Blade Carriage over the Twin Sliding Poles without any trimming material on a regular basis, to maintain its sharpness.
- To ensure a smooth and silent sliding motion, apply some lubricant to the Twin Sliding Poles occasionally. Always keep the rotary blade clean from dusts and residues.
WARRANTY POLICY
Your has a warranty of one year, from its purchase date. In the event of a manufacturer defect, your distributor ( at option ) will repair or replace it. IMPORTANT: This warranty does not cover damages due improper use or mishandling of the unit, including any extraordinary event leading to the damage, whether it is foreseeable or not.
If your is not trimming properly, first follow the Operation Instructions above. If the problem persists, please contact your dealer for further instructions. Please have your machine's serial number and the purchase date ready. If the machine must be returned to your distributor, it is your responsibility to properly pack it and ship it, as any damage incurred during its transportation will not be covered by our warranty policy.
Page 2 of 2 · End of manual
Quick start
- Place the RollaBlade on a sturdy table.
- Move the blade carriage to either end of the sliding poles; it trims in both directions.
- Set the depth guide to your measurement using the ruler guide.
- Slide the material under the clamping bar and align it against the ruler guide and depth guide.
- Hold the material and slide the blade carriage across in one movement. Keep fingers off the clamping bar.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Blade carriage is hard to slide | Too much material is being trimmed, or the poles need lubricant. | Do not exceed the 2.0 mm trimming capacity. Adjust the sheets so the carriage slides comfortably. Apply some lubricant to the Twin Sliding Poles. Page 2 |
| Blade seems dull | The self-sharpening blade is not being maintained. | Slide the Blade Carriage over the Twin Sliding Poles with no material in place on a regular basis. Page 2 |
| Sliding is rough or noisy | The poles need lubricant or the blade is dirty. | Apply some lubricant to the Twin Sliding Poles occasionally. Keep the rotary blade clean from dust and residue. Page 2 |
| Risk of injury | Fingers are near the blade or clamping bar. | Never place fingers under the Blade Carriage, never touch the table blade, and do not press fingers on the Clamping Bar while trimming. Page 2 |
| Damage when moving the trimmer | It was carried by the twin poles. | Always carry or pull it by the baseboard. Never carry it by the twin poles. Page 2 |
| Trimmer is not trimming properly | Unknown fault. | Follow the operation instructions first. If the problem persists, contact your dealer. Page 2 |
Frequently asked questions
How thick a material can the RollaBlade cut?
Up to 2.0 mm. Never exceed this capacity, and adjust the number of sheets so the carriage slides comfortably. See page 2.
What materials can it trim?
Paper, newsprint, cardboard, plastic films, polycover, vellum, aluminum foil, vinyl, PVC, polyester, polypropylene, polyethylene, leather, veneer and more. See page 2.
How do I keep the blade sharp?
The blade self-sharpens. Regularly slide the carriage along the poles with no material in it, and keep the blade clean of dust and residue. See page 2.
How do I keep the carriage sliding smoothly?
Occasionally apply some lubricant to the twin sliding poles. See page 2.
