Page 1 of 5
Text on page 2
WireMac DUO OPERAT IO N MA NUAL
INTRODUCTION
CONGRATULATIONS ON THE PURCHASE OF YOUR NEW WIREMAC DUO, A PROFESSIONAL AND HEAVY-DUTY WIRE PUNCH AND BINDING MACHINE. YOUR DUAL TWIN BINDER WAS DESIGNED WITH A FULL RANGE OF FUNCTION AND PREMIUM QUALITY COMPONENTS TO GUARANTEE YOU AN EFFORTLESS AND PROFESSIONAL BIND, AS WELL AS MANY YEARS OF TROUBLE-FREE SERVICE.
IMPORTANT
WE RECOMMEND THAT YOU TAKE A FEW MINUTES TO FAMILIARIZE YOURSELF WITH THE FUNCTIONS OF YOUR NEW WIREMAC DUO. YOU WILL FIND THAT WITH JUST A LITTLE PRACTICE, ANY PERSON CAN ACHIEVE PROFESSIONAL RESULTS.
F E AT URES
Die Disengagement Pins 3:1
Punch Throat & Ruler For 2:1
Punch Handle For 3:1
Punch Handle For 2:1
Side Margin Control For 3:1
SELECTOR:
Punch Size Wire Size Wire Closure Depth Margin
Depth Margin Control For 2:1
Depth Margin Control For 3:1
Continuous Punch Guide
Paper Scale Waste Drawer Wire Snatch
Punch Throat & Ruler For 3:1
ASSEMB LY
- Place your new WireMac DUO on top of a sturdy working table.
- Remove The Screw from Punching Axle clockwise as indicated, connect 2 Punch Handles, the longer one for 3:1 and the shorter one for 2:1 in a vertical position onto the Punch Axle. Tighten-back the Screws counter clockwise.
- Repeat the same for Closing Handle ( The shorter one ).
Page 2 of 5
Text on page 3
SET-UP
Insert a full unbound document into Paper Scale.
- Read the Selector to determine the correct:
- -Punch pitch 3:1 or 2:1
- -Depth Margin
- -Wire Size
- -Wire Closure
- Set Depth Control to the color determined depth margin. Color
indicated on Depth Control should match color on Selector.
- Set Wire Closer Control to the determined wire closure size.
TIPS
There may be different size of 3:1 or 2:1 on some wire diameter than the standard, please make sure your onhand wire before punching 3:1 or 2:1.
- Read the determined wire size and set aside.
PUNCHING
- Move Side Margin Control to proper sheet & cover size.
11"
11-1/4" COVER
Note There are different side margins for 11" sheets & their 11-1/4" Covers.
TIPS
Maximum single punching: 20 sheets of 20 Lbs or 70-80g/m paper.
- Pull out disengagement pins for partially covered holes.
- Insert sheets and pull handle forward to punch. 2:1 holes
Re-Align ( Center) margins for oversize covers.
Comfortable single punching: 12-15 sheets of 20 Lbs or 70-80 g/m paper.
Punch inner sheets and cover separately as side margin may vary.
Page 3 of 5
Text on page 4
FOR PUNCHING DOCUMENT LARGER THAN 14" (356MM)
- Align Sheets as indicated on Punch Throat Ruler. Insert sheets and pull handle forward to punch the left part first. See Picture 1
- Remove sheets and flip them over as illustrated. See Picture 2.
- Insert sheet from right-hand-side. Pull the handle forward and punch. See picture 3. IMPORTANT: Document must be inserted in such a way as to place one of the already perforated holes onto the Continuous Punch Guide.
regnoL " 4 1
INSERTING
- Insert pre-selected wire into Wire Snatch
Front Cover
Back Cover
IS O PR -9 O 0 02 JE C T
TIPS
The seam of closed wire should be inside the book. Follow step No.2 instruction for best results.
- Insert document from last pages to first pages then insert front cover. The back cover should be inserted last with inside facing up.
Back Cover
Last Page
Front Cover Back Cover
Front Cover
- Take out inserted document from Wire Snatch to close the wire.
Ba ck
Co ver
CLOSING
- Put inserted document into wire closer.
The wire element must stand horizontally at the bottom of closer.
TIPS
- Pull closer handle Forward to close.
The seam of closed wire should be just touching. Slightly adjust the Closer Control a little left or right for the under-closed or over- closed seam.
OK
- Take out document and turn back cover over. The binding is ready.
Page 4 of 5
Text on page 5
TECHNICAL INFORMATION
Size
Size 3 : 1 ( 3 HOLES PER INCH )
Punching Length
14"
LEGAL
= 40 Holes = 38 Holes
14" = 27 Holes LEGAL = 26 Holes
= 34 Holes = 32 Holes = 24 Holes = 24 Holes
Sheets Diameters mm 70-80 g/m 2 Inch
Binding Capacity
Size 2 : 1 (2 HOLES PER INCH )
= 23 Holes = 21 Holes = 16 Holes = 16 Holes
Sheets 70-80 g/m 2
Diameters Inch
WA RRANTYPOLICY
YOUR WIREMAC DUO HAS A WARRANTY OF ONE YEAR FROM DATE OF PURCHASE. IN THE EVENT OF A MANUFACTURER'S DEFECT, YOUR DISTRIBUTOR (AT OPTION) WILL REPAIR OR REPLACE IT. IMPORTANT: THIS WARRANTY DOES NOT COVER DAMAGES DUE TO IMPROPER USE OR MISS TREATMENT OF THE UNIT, INCLUDING ANY EXTRAORDINARY EVENT LEADING TO THE DAMAGE OF THE MACHINE, WHETHER IT IS REVERSIBLE OR NOT.
IF THE WIREMAC DUO IS NOT WORKING PROPERLY, FIRST FOLLOW THE CORRECTIVE ACTIONS ABOVE. IF THE PROBLEM PERSISTS, PLEASE CONTACT YOUR DEALER FOR FURTHER INSTRUCTIONS. PLEASE HAVE YOUR MACHINE'S SERIAL NUMBER AND THE PURCHASE DATE READY. IF THE MACHINE MUST BE RETURNED TO YOUR DISTRIBUTOR, IT IS YOUR RESPONSIBILITY TO PROPERLY PACK AND SHIP IT. AS ANY DAMAGES INCURRED DURING ITS TRANSPORTATION IS NOT COVERED BY OUR WARRANTY POLICY.
Page 5 of 5 · End of manual
Quick start
- Place the machine on a sturdy table and attach the two punch handles (longer for 3:1, shorter for 2:1) and the closing handle.
- Insert the full unbound document into the Paper Scale and read the selector for pitch, depth margin, wire size and closure.
- Set the Depth Control to the matching color and the Wire Closer Control to the closure size.
- Move the side margin control to the sheet or cover size and pull out disengagement pins for partially covered holes.
- Insert sheets and pull the handle forward to punch; punch inner sheets and covers separately.
- Insert pages last to first onto the wire in the wire snatch, then the front cover, and the back cover last with the inside up.
- Place the document in the closer with the wire horizontal, pull the handle forward, then turn the back cover over.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Wire is under-closed or over-closed | Closer setting does not match the wire. | Adjust the Closer Control a little left or right until the seam is just touching. Page 4 |
Frequently asked questions
How many sheets can the WireMac Duo punch?
Up to 20 sheets of 20 lb (70–80 g/m²) paper; 12–15 sheets is the comfortable range. See page 3.
How do I know whether to use 3:1 or 2:1 pitch?
Insert the full document into the Paper Scale and read the selector, which shows the punch pitch, depth margin, wire size and closure. Check your on-hand wire before punching. See page 3.
Can it punch documents longer than 14 inches?
Yes. Punch the left part first, flip the sheets, and punch from the right with one punched hole placed on the Continuous Punch Guide. See page 4.
What warranty does the WireMac Duo have?
One year from the date of purchase against manufacturer defects. See page 5.
