Page 1 of 6
Page 2 of 6
Text on page 3
Xtra Wide Presentation Cart
Hardware List
Should you require assistance during assembly, please call our Customer Service Department Monday - Friday 8 a.m. - 5 p.m. Central Standard Time 1-800-749-2258
We recommend that you assemble this unit on a table.
Do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorized parts.
Page 3 of 6
Text on page 4
Xtra-Wide Presentation Cart
Assembly Diagram
R EAD T HROUGH I NSTRUCTIONS
FROM BEGINNING TO END BEFORE
STARTING TO ASSEMBLE UNIT .
1.) Identify and Separate all the Parts and Hardware.
2.) Attach Top Platform (P-3) and Lower Shelf (P-5) to the Left & Right Leg Assemblies (P1 & P2) using 10 screws (A) as shown in illustration # 1. (Finger tighten only)
Grommet (D) P-10
Cap Sleeve
Grommet(D) installation Illustration # 2
3.) To install Grommet (D) in LCD Platform (P-6), separate parts and press Grommet Sleeve in rectangular opening as shown in illustration # 2.
4.) Snap 2 plastic Caps over top of Sleeve as shown in illustration 2.
Page 4 of 6
Text on page 5
4.) Attach 2 Locking Casters (B) to the front, and 2 Casters (C) to the back of the unit. Tighten all Casters using Caster Wrench (J).
5.) Place 1 Hex Nut (E) and 1 Flat Washer (F) on each CPU Rod (P-11). Insert 2 CPU Rods (P-11) through the Left Leg (P-1) or the Right Leg (P-2) as shown in illustration # 3.
6.) Place 1 Black Plastic Spacer (G) over each CPU Rod (P-11) and secure each Rod with 1 P-10 Flat Washer (F) and 1 Hex Nut (E). Slide CPU Sleeve (P-10) over ends of CPU Rods as shown in illustration # 3.
- Slide LCD Platform (P-6) Between Left & Right Leg Assemblies (P-1 & P-2) and attach using 4 Screws (A) as shown in illustration # 3.
8.) Attach 2 Stability Panels (P-7) to the Left & Right Leg Assemblies (P-1 & P-2) using 8 Screws (A) as shown in illustration # 4. (Finger tighten only)
Missing Parts or UPS Damaged Parts For Your Convenience you can EMAIL us at
24HOURS 7 DAYS A WEEK
Page 5 of 6
Text on page 6
9.) Attach Right Shelf Bracket (P-8) and Left Shelf Bracket (P-9) to Laptop Shelf (P-4) using 4 screws (A) as shown in illustration # 5. (Finger tighten only)
10.)Attach Right Shelf Bracket (P-8) and Left Shelf Bracket (P-9) to the Right & Left Leg Assemblies (P1 & P2) at the desired height as P-1 shown in illustration # 6. (Tighten 4 screws under Laptop Shelf (P-4) using Allen Wrench (H)).
(Tighten all the screws at this time using Allen Wrench (H)).
Important
The Balt product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal use due to defect or imperfection, the defective part or product will be replaced. Damage caused by common carriers during shipment is not included in this guarantee.
This guarantee sets forth all applicable guarantees and remedies. No other warranty, expressed or implied shall apply. Failure to follow instructions found in Important Information Section of Owner Sheet shall void the guarantee. Consequential or incidental damages and or costs are not refundable.
WWW.MYBINDING.COM
Page 6 of 6 · End of manual
Quick start
- Read the instructions through first, assemble on a table, and identify and separate all parts and hardware.
- Attach the top platform (P-3) and lower shelf (P-5) to the left and right leg assemblies (P-1, P-2) with 10 screws (A), finger tight.
- Press the grommet sleeve into the LCD platform (P-6) opening and snap the 2 plastic caps over it.
- Fit 2 locking casters (B) at the front and 2 casters (C) at the back and tighten them with the caster wrench (J).
- Install the 2 CPU rods (P-11) through a leg with hex nuts (E), flat washers (F) and black spacers (G), then slide on the CPU sleeve (P-10).
- Attach the LCD platform with 4 screws (A) and the 2 stability panels (P-7) with 8 screws (A).
- Attach the shelf brackets (P-8, P-9) to the laptop shelf (P-4), mount it on the legs at the height you want, then tighten all screws with the Allen wrench (H).
Frequently asked questions
Should the cart be assembled on the floor?
Balt recommends assembling this unit on a table. See page 3.
How often should I check the screws?
Do not use the cart unless all screws are tight, and check them at least every six months. See page 3.
Can the laptop shelf height be adjusted?
Yes. The shelf brackets attach to the leg assemblies at the height you choose. See page 6.
What is the warranty on the Balt 27517?
Balt guarantees the product against material and workmanship defects for 1 year from the date of purchase. Shipping damage caused by carriers is not covered. See page 6.
