Page 1 of 6
Page 2 of 6
Text on page 3
#27553 Wide Body LCD Cart
Hardware List
Sq Hd Screw M8x15mm
Screw M5X70mm Pan Hd
Hex nut M8 w/Flange
Hex nut M5 w/Flange
installed in end of monitor tubes
Screw M8X25mm Dog Point
back of monitor tube-Top
Screw M8X25mm Cone Point
back of monitor tube-Bottom
Do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorized parts.
Page 3 of 6
Text on page 4
#27553 Wide Body LCD Cart
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING TO END
BEFORE STARTING TO ASSEMBLE UNIT .
1.) Identify and Separate all the Parts and Hardware.
2.) Attach 2 Legs (P-1) and 2 Legs (P-2) to the Top Shelf (P-3) using 8 screws (A1), and 8 Nuts (B1)as shown in illustrations #1.
Note- “X” or “O” stamped in Bracket on each leg
3.) Slide Middle Shelf (P-4) in between the 4 Legs (P1 & P-2) and attach using 8 screws (A1), and 8 Nuts (B1) as shown in illustration # 2.
Note- “X” or “O” stamped in Bracket on each leg
4.) Slide Bottom Shelf (P-5) in between the 4 Legs (P1 & P-2) as shown in illustration #2.
Important
The Balt product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal use due to defect or imperfection, the defective part or product will be replaced. Damage caused by common carriers during shipment is not included in this guarantee. This guarantee sets forth all applicable guarantees and remedies. No other warranty, expressed or implied shall apply. Failure to follow instructions found in Important Information Section of Owner Sheet shall void the guarantee. Consequential or incidental damages and or costs are not refundable.
Page 4 of 6
Text on page 5
Note: Be sure that grommet in Middle Shelf (P4) is
toward the back as shown in illustration # 3.
5.) Secure Bottom Shelf (P-5) to the 4 Legs (P-1 & P-2) using 8 screws (A1) and 8 Nuts (B1) as shown in illustration # 4.
6.) Press 2 Locking Casters (C) and 2 non-locking casters (D) into the factory installed nylon inserts in the Legs (P-1 & P-2) as shown in illustration #4.
Missing Parts or UPS Damaged Parts For Your Convenience you can EMAIL us at
24HOURS 7 DAYS A WEEK
Page 5 of 6
Text on page 6
7.) Remove Screws (A3) from bottom of left and Right Support Tubes (P-6 & P-7) and attach to Top Shelf (P-3) as shown in illustration # 5.
8.) Attach Cord Winder (P-10) and Electrical Outlet (P-11) to Top Shelf (P-3) using 2 screws (A2) and 2 Nuts (B2).
9.) Attach Bottom LCD Bracket (P-9) to Left and Right Support Tubes (P-6 & P-7) at desired height using 2 screws (A5).
10.) Attach Top LCD Bracket (P-8) to Left and Right Support Tubes (P-6 & P-7) at desired height using 2 screws (A4) as shown in illustration # 6.
Should you require assistance during assembly, please call our Customer Service Department Monday - Friday 8 a.m. - 5 p.m. Central Standard Time 1-800-749-2258
WWW.MYBINDING.COM
Page 6 of 6 · End of manual
Quick start
- Read the instructions through first, then identify and separate all parts and hardware.
- Attach 2 legs (P-1) and 2 legs (P-2) to the top shelf (P-3) with 8 screws (A1) and 8 nuts (B1), matching the X or O stamped on each leg bracket.
- Slide in the middle shelf (P-4), grommet toward the back, and attach it with 8 screws and nuts.
- Slide in the bottom shelf (P-5) and secure it with 8 screws (A1) and 8 nuts (B1).
- Press 2 locking and 2 non-locking casters into the factory-installed nylon inserts in the legs.
- Remove the screws (A3) from the bottom of the support tubes (P-6, P-7) and use them to attach the tubes to the top shelf.
- Attach the cord winder (P-10) and electrical outlet (P-11) to the top shelf, then fit the bottom (P-9) and top (P-8) LCD brackets to the support tubes at the height you want.
Frequently asked questions
How do the casters attach?
Press the 2 locking and 2 non-locking casters into the factory-installed nylon inserts in the legs. See page 5.
Can the LCD mount height be adjusted?
Yes. The top and bottom LCD brackets attach to the support tubes at the height you choose. See page 6.
Which way does the middle shelf face?
The grommet in the middle shelf should be toward the back. See page 5.
What is the warranty on the Balt 27553?
Balt guarantees the product against material and workmanship defects for 1 year from the date of purchase. Shipping damage caused by carriers is not covered. See page 4.
