Page 1 of 6
Page 2 of 6
Text on page 3
27614 Beta Cart
Hardware List
Book Stop Phillips Screw
Electrial Strip Screws (Optional)
Page 3 of 6
Text on page 4
Assembly Diagram
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING
TO END BEFORE STARTING TO ASSEMBLE UNIT . 1.) Identify and Separate all the Parts and Hardware. 2.) Screw in two Locking Casters (A) into the bottom front of the Base (P1) and two Non-Locking Casters (B) as shown in Illustration # 1. Tighten casters with Caster Wrench (F).
3.) Insert the Pole (P2) into the Base (P1) and secure to the Base using one long Bolt (D) and four small Screws (G) as shown in illustration #2.
4.) Open the clamp up on the Main Platform (P3) and slide the assembly down the Pole (P2). Make sure the friction button inside the clamp is retracted. When the Main Platform is in position, lock the clamp lever down to secure it in place as shown in illustration #3. Attach the Book Stop (L) to the Main Platform (P3) using three Book Stop Screws (K) as shown in illustration #3a.
Page 4 of 6
Text on page 5
5.) Slide the Monitor Mount (P4) down the Pole (P2) above the Main Platform (P3)and tighten the clamp lever down to lock in place. See illustration #4.
5A.) To adjust the tension of the Monitor Mount (P4), remove caps and use the Wrenches (H) to tighten or loosen nuts.
6.) Snap-On three Cable Ties (C) onto the Pole (P2) . See illustration #4.
7.) Attach the two CPU Mounts (P5) to the Pole (P2) using four Screws (J) through two CPU Mount Clamps (P6) as shown in illustration #5. Tighten Screws (J) with Allen Wrench (E).
7a.) Use two CPU Straps (I) through the slots in the CPU Mounts (P5) to secure your CPU in place. See illustration #5a. 27614_07-08-14
WWW.MYBINDING.COM
Page 5 of 6
Text on page 6
27614
Beta Cart
VESA 3 and VESA 4 Mount
All Parts Have Adjustable Height
Adjustable CPU Holder
20” W X 12” D Keyboard Shelf w/ 6 5/8” X 6” Mouse
Page 6 of 6 · End of manual
Quick start
- Identify and separate all parts and hardware.
- Screw two Locking Casters (A) into the bottom front of the Base (P1) and two Non-Locking Casters (B) into the rear; tighten with the Caster Wrench (F).
- Insert the Pole (P2) into the Base and secure it with one long Bolt (D) and four small Screws (G).
- Open the clamp on the Main Platform (P3), retract the friction button, slide it down the pole and lock the clamp lever. Attach the Book Stop (L) with three screws (K).
- Slide the Monitor Mount (P4) down the pole above the platform and lock the clamp lever. To adjust its tension, remove the caps and use the Wrenches (H) on the nuts.
- Snap three Cable Ties (C) onto the pole.
- Attach the two CPU Mounts (P5) to the pole through the CPU Mount Clamps (P6) with four Screws (J), then run the CPU Straps (I) through the slots to hold the CPU.
Frequently asked questions
What monitor mounting does the 27614 Beta Cart support?
It has a VESA 3 and VESA 4 mount. See page 6.
How big is the keyboard shelf?
20" W x 12" D, with a 6 5/8" x 6" mouse area. See page 6.
Can the parts be adjusted for height?
Yes. All parts have adjustable height; the platform and monitor mount clamp to the pole with lever clamps. See page 4 and page 6.
How do I adjust the monitor mount tension?
Remove the caps and use the supplied Wrenches (H) to tighten or loosen the nuts. See page 5.
