Page 1 of 14
Page 2 of 14
Text on page 3
Odyssey Laptop Charging Cart
Hardware List
M6X45 mm Socket Screw
M6X65 mm Socket Screw
4” Locking Plate Caster
Upper Back Panel 1 EA
Bottom Back Panel 1EA
Electrical Mount Screw M5
Page 3 of 14
Text on page 4
Odyssey Laptop Charging Cart
Hardware List
Page 4 of 14
Text on page 5
R EAD T HROUGH I NSTRUCTIONS FROM
BEGINNING TO END BEFORE STARTING TO ASSEMBLE UNIT .
1.) Identify and Separate all the Parts and Hardware.
2.) Attach two Locking Casters (C) to the bottom front and two Non-Locking Casters (D) to the bottom rear of Metal Base (P-1) using four Screws (A) for each caster. See Illustration #1.
2a.) Place a Grommet- Base (B) in each of the two large holes in the Metal Base (P1).
Attach one of the Side Handles (P-4) to the left side of Metal Base (P-1) using two Screws (A2) as shown in Illustration #2. Front
Page 5 of 14
Text on page 6
4.) Attach the Left Side Panel (P5) to the Side Handle (P4) using four Screws (A1) and four Tapped Rivets (G) as shown in Illustration # 3.
5.) Secure the Left Side Panel (P5) to the Metal Base (P1) using two Screws (A) as shown in Illustration # 4.
Page 6 of 14
Text on page 7
6.) Screw in two Cam Posts (I) into the embedded plastic inserts in the Left Side Panel (P5) as shown in Illustration # 5. Install two Cams (H) into the large holes in the Bottom Back Panel (P7-1). Install a Wood Dowel (J) in the center hole on the edge of the Bottom Back Panel (P7-1). With the Cam’s (H) arrows pointed at the Cam Posts (I), slide the Bottom Back Panel (P7-1) into place and turn the Cams clockwise a quarter turn to the lock position.
7.) Center the Back Frame (P8) over the two embedded threaded metal inserts in the Left Side Panel (P5) and secure with two Screws (A) as shown in Illustration # 6.
Page 7 of 14
Text on page 8
8.) Screw in two Cam Posts (I) into the embedded plastic inserts in the Left Side Panel (P5) as shown in Illustration # 5. Install two Cams (H) into the large holes in the Upper Back Panel (P7). Install a Wood Dowel (J) in the center hole on the edge of the Upper Back Panel (P7). With the Cam’s (H) arrows pointed at the Cam Posts (I), slide the Upper Back Panel (P7) into place and turn the Cams clockwise a quarter turn to the lock position.
Place two Cams (H) in the Upper Back Panel (P7) and two Cams (H) in the Bottom Back Panel (P7-1) making sure the arrows on the Cams (H) are pointe to the right as shown in Illustration # 8. Push in one Wood Dowel (J) into the edge of the Upper Back Panel (P7) and one Wood Dowel (J) into the edge of the Bottom Back Panel (P7-1). Screw in four Cam Posts (I) into the the Right Side Panel (P6). Move the Right Side Panel (P6) in to connect. Turn the Cams (H) a quarter turn to lock. Secure the Back Frame (P8) to the Right Side Panel (P6) using two Screws (A).
Page 8 of 14
Text on page 9
10.) Attach the Right Side Panel (P6) to the Side Handle (P4) using four Screws (A1) and four Tapped Rivets (G) as shown in Illustration # 9.
11.) Secure the Right Side Panel (P6) to the Metal Base (P1) using two Screws (A) as shown in Illustration # 10.
Page 9 of 14
Text on page 10
12.) Insert two Cams (H) into the top of the Left Side Panel (P5) and one into the top left of the Back Panel (P7) making sure the arrow on the Cams (H) are pointed up. Press in two Wood Dowels (J) into the top edge of the Left Side Panel (P5). Screw in three Cam Posts (I) into the bottom left of the Top Panel (P2) as shown in Illustration # 11. Repeat these same Steps to install Cams(H), Wood Dowels (J) and Cam Posts (I) into the Right Side Panel (P6), the Back Panel (P7) and under the right bottom of the Top Panel (P2). Lower the Top Panel (P2) down onto the assembly and turn the Cams a quarter turn to lock into place.
Place the Back Lock (P) into the Center Back Panel (P10) from the outside and in. Use the Lock Clip (Q) on the back side of the Back Lock (P) to secure it in place. Place the bottom pegs on the Center Back Panel (P10) into the two holes in the bottom of the Back Frame (P8) and lock the Back Lock (P) to keep the Center Back Panel (P10) in place. See Illustration # 12.
Page 10 of 14
Text on page 11
14.) Attach two Electrical Mounts (K) to the top Back Panel (P7) and two to the bottom Back Panel (P7) using one Electrical Mount Screw (L) into each embedded threaded insert as shown in Illustration # 13.
Snap in a large Electrical Strip (M) into the top Electrical Mounts (K) with the cord exiting to the right. Snap in a second large Electric Strip (M) into the bottom Electrical Mounts (K) with the cord exiting to the left as shown in Illustration # 14.
Electrical Cord
Electrical Cord
Page 11 of 14
Text on page 12
16.) Insert the Shelf Pins (R) into the predrilled shelf location holes in the Right Side Panel (P6) and the Left Side Panel (P5) as shown in Illustration #15a. Place each Shelf (P3) on the Shelf Pins (R) making sure the notches in the side flanges on each Shelf (P3) hook onto the Shelf Pins (R).
Attach the two Vertical Supports (P11) to the Top Panel (P2) and to the Metal Base (P1) using Screws (A) into the threaded holes as shown in Illustration #16.
Page 12 of 14
Text on page 13
18.) Attach two Door Hinges (S) to the Left Side Panel (P5) using four Hinge Screws -Wood (T) into the prdrilled locate holes for each hinge. Attach the Left Door (P12) to the Door Hinges (S) using two Hinge Screws-Metal (U) as shown in Illustration #17.
Repeat Step 18 to install the Right Door (P13) to the Right Side Panel (P6) as shown in Illustration # 18.
Page 13 of 14
Text on page 14
Push in a Grommet (V) into the large hole at the bottom of the Right Side Panel (P6) and Left Side Panel (P5)
21.) Install Magnet (X) under the Top Panel (P2) in the front center so it catches and holds the Left Door (P12) when it is closed. Use two Magnet Screws (Y) to secure.
WWW.MYBINDING.COM
Page 14 of 14 ยท End of manual
Quick start
- Identify and separate all parts and hardware.
- Attach two Locking Casters (C) to the front and two Non-Locking Casters (D) to the rear of the Metal Base (P-1) with four Screws (A) each, and place a Grommet (B) in each large base hole.
- Attach the Side Handles (P-4), then fit the Left Side Panel (P5) to the handle and base.
- Join the Bottom and Upper Back Panels to the side panels with Cams (H), Cam Posts (I) and Wood Dowels (J), turning each cam a quarter turn clockwise to lock. Secure the Back Frame (P8) with Screws (A).
- Add the Right Side Panel (P6) and Top Panel (P2) the same way, then fit the Center Back Panel (P10) with the Back Lock (P).
- Mount four Electrical Mounts (K) and snap in the two Electrical Strips (M): top cord exiting right, bottom cord exiting left.
- Insert the Shelf Pins (R) and set the Shelves (P3), attach the Vertical Supports (P11), hang both doors on their hinges, and install the door Magnet (X) under the top panel.
Frequently asked questions
How many electrical strips does the Odyssey cart hold?
Two large Electrical Strips (M), one on the upper back panel and one on the lower. See page 11.
What size casters does it use?
The hardware list includes 4" locking plate casters. Two locking casters go on the front and two non-locking on the rear. See page 3 and page 5.
How do the cam locks work?
Point the cam arrows at the cam posts, slide the panel into place and turn the cams clockwise a quarter turn to lock. See page 7.
Can the back of the cart be locked?
Yes. The Center Back Panel (P10) has a Back Lock (P) that keeps it in place on the Back Frame. See page 10.
