Page 1 of 11
Page 2 of 11
Text on page 3
#27689 Economy Tablet Charging Cart
Hardware List
Screw 1/4” X 15mm
Screw 1/4” X 10mm
Screw 1/4” X 45mm
Page 3 of 11
Text on page 4
Electrical Cord Grommet 1 EA
- #58208-8 Outlet Electrical Strips
These parts are not used.
Page 4 of 11
Text on page 5
Assembly Diagram
- Identify and seperate all parts.
- Place the Top Panel (P-1) face down on a padded surface as shown in illustration #1. Connect the Right Metal Side (P-8) to the Top Panel (P-1) using two Screws (B) and going into the embedded threaded inserts in the bottom of the Top Panel. Attach the Left Metal Side (P-7) to the Top Panel using two Screws (B). Tighten Screws with Allen Wrench (G).
Page 5 of 11
Text on page 6
- Attach a Wood Side Panel (P-10) to the outside of each Metal Side using two Screws (A1) to secure each panel into place. See illustration # 2.
- Place a Shelf (P-3) on the shelf brackets of the Right and Left Metal Sides and secure in place using one Screw (A1) on each end as shown in illustration #3. Tighten with Allen Wrench (G).
Repeat this Step to install the remaining 7 Shelves.
Page 6 of 11
Text on page 7
- Push in four Wood Dowels (Q) into the top edge and bottom edge predrilled holes of the Left Back Panel (P-12) as shown in illustration #4. Attach two Electrical Clips (H) to the inside of the Left Back Panel (P-12) using two Electrical Clip Screws(D) and two Plastic Spacers (W). Attach the Rear Door (P-6) to the Left Back Panel (P-12) using four Door Hinge Screws (P). Insert the Rear Door Lock (L) in from the front and use the Rear Lock Clip (M) as shown to secure in place.
Push in four Wood Dowels (Q) into the top edge and bottom edge predrilled holes of the Right Back Panel (P-11) as shown in illustration #5. Attach two Electrical Clips (H) to the inside of the Right Back Panel (P-11) using two Electrical Clip Screws(D) and two Plastic Spacers (W).
Page 7 of 11
Text on page 8
- Place the Back Panel assemblies from Step 5 and Step 6 in between the Right and Left Side assemblies as shown in illustration #6. Make sure the Wood Dowels of the assemblies are insert into the predrilled holes in the bottom of the Top Panel (P-1). Secure the Back assemblies to each Side Panel assembly using three Screws (C). Tighten Screws with Allen Wrench (G). Attach the Magnet (T) to the bottom of the Top Panel (P-1) using two Magnet Screws (U) into the predrilled holes so the Rear Door (P-6) stops against the Magnet. See Detail 7A.
- To attach the Bottom Panel (P-2) to the assembly from Step 7, line up the Wood Dowels in the Back assemblies with the predrilled holes in the Bottom Panel (P-2). Attach the Bottom Panel (P-2) to the Side assemblies using four Screws (B) as shown in illustration #7. Tighten Screws with Allen Wrench (G).
Page 8 of 11
Text on page 9
- Attach two Locking Casters (E) in the front embedded insert holes of the Bottom Panel (P-2) using eight Screws (A) as shown in illustration #8. Attach two Non-Locking Casters (F) in the rear embedded insert holes of the Bottom Panel using eight Screws (A). Tighten Screws with Allen Wrench (G). Press in the Electrical Grommet (V) in the Left Back Panel’s cut-out.
- Turn the unit over so the Casters are on the floor. Attach the Left Door (P-5) to the hinge on the Side assembly using six Door Hinge Screws (P) into the Door’s predrilled hinge holes. Attach the Door Latch (N) to the top of the Left Door using four Door Latch Screws (O) as shown in illustration #9. Attach an Electrical Cord Holder (R) at the top and bottom of the Right Metal Side and through the punched holes so one is pointed up and the other down. Secure Holders using two Cord Holder Nuts (S) from the inside. See Detail 10A.
Page 9 of 11
Text on page 10
11. Attach the Right Door (P-4) to the hinge on the Side assembly using six Door Hinge Screws (P) into the Door’s predrilled hinge holes. Attach the Door Lock (J) to the back of the Right Door using four Door Screws (P) as shown in illustration #10. Push the Door Lock Bezel (K) in from the front and around the Door Lock barrel.
11A. Attach a Magnet (T) to the Bottom Panel (P2) using two Magnet Screws (U) and going into the two predrilled holes as shown in Detail 11A. Attach a Magnet Plate (Y) to the bottom corner of the Right Door (P4) using one Screw (U).
12. Snap in an Electrical Strip (58208) into the Electrical Clips (H) on the Left Back Panel (P-12) and one Electrical Strip (58208) into the Electrical Clips (H) on the Right Back Panel (P-11) as shown in illustration #11. Make sure the cords on the Electrical Strips are at the bottom so they can exit out the Grommet.
Page 10 of 11
Text on page 11
27689
Economy Tablet Charging Cart
Two Locking -Front Two Non-Locking -Back
Shelves (8): 16 1/2” W X 7 7/8” D 2 1/8” Space Between
Two Electrical Outlet Strips each with 8 Outlets and 15’ Cords
WWW.MYBINDING.COM
Page 11 of 11 ยท End of manual
Quick start
- Identify and separate all parts. Note the #58208-8 outlet electrical strips listed on page 4 are not used.
- Lay the Top Panel (P-1) face down on a padded surface and attach the Right and Left Metal Sides with two Screws (B) each, then add a Wood Side Panel (P-10) to the outside of each metal side.
- Set each of the 8 Shelves (P-3) on the side brackets and secure with one Screw (A1) at each end.
- Prepare the Left and Right Back Panels with Wood Dowels (Q) and Electrical Clips (H); hang the Rear Door (P-6) and its lock on the left back panel.
- Fit the back panel assemblies between the sides, secure with Screws (C), add the rear door Magnet (T), then attach the Bottom Panel (P-2) with four Screws (B).
- Attach two Locking Casters (E) at the front and two Non-Locking Casters (F) at the rear with eight Screws (A) each, and press the Electrical Grommet (V) into the left back panel.
- Turn the cart upright, hang the Left Door with its Door Latch (N) and the Right Door with its Door Lock (J), add the cord holders and door magnet, then snap the Electrical Strips into the clips with cords at the bottom.
Frequently asked questions
How many tablet shelves does the 27689 cart have?
Eight shelves, each 16 1/2" W x 7 7/8" D with 2 1/8" of space between them. See page 11.
What electrical strips are included?
Two electrical outlet strips, each with 8 outlets and a 15' cord. See page 11.
Which casters lock?
The two front casters lock; the two rear casters do not. See page 11.
Which way should the electrical strip cords face?
Snap the strips in with the cords at the bottom so they can exit through the grommet. See page 10.
