Page 1 of 8
Text on page 2
WOW
27698 A La Cart
Hardware List
- #58208-8 Outlet Electrical Strip
Page 2 of 8
Text on page 3
Assembly Diagram
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING
TO END BEFORE STARTING TO ASSEMBLE UNIT . 1.) Identify and seperate all Parts and Hardware.
2.) Attach two Casters (A) into the right holes of the Base (P1) using four Caster Screws (L) to secure each. Attach two Locking Casters (B) into the left threaded holes on the bottom of the Base (P1) using four Caster Screws (L) to secure each. Use the Allen Wrench (G) to tighten Screws as shown in illustration # 1.
3.) Attach a Door Assembly (P2) to the front holes in top of the Base (P1) using two Screws (F). Attach the second Door Assembly (P2) to the rear holes in top of the Base (P1) using two Screws (F) as shown in Illustration # 2. Tighten Screws with Allen Wrench (G).
WWW.MYBINDING.COM
Page 3 of 8
Text on page 4
4.) Align the internal threaded posts on the Right Side Panel (P3) with the holes in the sides of the front and back Door Assemblies (P2) and secure in place using six Screws (F). Repeat this Step to intall the Left Side Panel (P4) as shown in illustration # 3
5.) Attach nine of the Tablet Dividers (C) into each slot in Shelf (P5) as shown in illustration #4. Secure in place by snapping on one Divider Connector (D) to the bottom rear tab on each Tablet Divider (C). Repeat this Step for the second slot in the Shelf. Repeat this same Step for the second Shelf (P5).
Page 4 of 8
Text on page 5
6.) Attach four Electrical Clips (EL2) to the rear flange on each Shelf (P5) using one Phillips CS Screw (EL3) and one Screw Block (E) for each as shown in illustration # 5. Repeat this Step for the second Shelf (P5).
7.) Place the bottom Shelf assembly down through the top of the cart so it rests on top of the bottom two shelf supports that are welded on each Side Panel. Place the top Shelf assembly down through the top of the cart so it rests on the top two shelf supports that are welded to the Side Panels. Make sure the back of each Shelf, with the Electrical Clips (EL2) , are facing the rear Doors of the cart as shown in illustration # 6. Secure Shelves in place using two Shelf Screws (J) and two Nuts (K) on each end (not shown).
Top Shelf Assembly
Bottom Shelf Assembly
Page 5 of 8
Text on page 6
8.) Attach a Handle (P6) to each Side Panel using one long Screw(H) in each end as shown in illustration # 7.
9.) Attach the Top (P7) through the holes in the Door Assemblies (P2) using four Screws (F) as shown in illustration # 8.
Page 6 of 8
Text on page 7
10.) Insert the Electrical Cord Holders (I) into the slots in the Right Side Panel (P-3) and secure in place using three Nuts (K) for each. See illustration # 9.
11.) Snap in the four Etectrical Outlet Strips (EL1) vertically into the Electrical Clips (EL2) on the back of each Shelf assembly as shown in illustration # 10.
Page 7 of 8
Text on page 8
12.) Remove the four nuts and washers from the inside of the cart that hold the cover plate behind the Timer cut-out. Discard the cover plate. Insert the Timer (M) from the inside over the threaded studs. Replace the four washers and four nuts to secure in place as shown in illustration #12.
Page 8 of 8 · End of manual
Quick start
- Identify and separate all parts and hardware.
- Attach two Casters (A) to the right holes and two Locking Casters (B) to the left holes of the Base (P1) with four Caster Screws (L) each.
- Attach the front and rear Door Assemblies (P2) to the base with two Screws (F) each, then fit the Right and Left Side Panels with six Screws (F) each.
- Snap nine Tablet Dividers (C) into each slot of both Shelves (P5), locking each with a Divider Connector (D), and add four Electrical Clips (EL2) to each shelf's rear flange.
- Lower the shelves onto the welded shelf supports with the clips facing the rear doors and secure with Shelf Screws (J) and Nuts (K).
- Attach the Handles (P6), the Top (P7) and the Electrical Cord Holders (I), then snap the four Outlet Strips (EL1) vertically into the clips.
- Remove the cover plate behind the timer cut-out, mount the Timer (M) from the inside over the studs, and replace the washers and nuts.
Frequently asked questions
How many tablet dividers go on each shelf?
Nine dividers in each slot, with two slots per shelf. See page 4.
How many outlet strips does the cart use?
Four electrical outlet strips, snapped vertically into the clips on the back of the shelves. See page 7.
How is the timer installed?
Remove the four nuts and washers holding the cover plate behind the timer cut-out, discard the plate, place the timer over the studs from inside and refit the washers and nuts. See page 8.
