Page 1 of 15
Text on page 2
Odyssey High Capacity Charging Cart
Hardware List
M6X45 mm Socket Screw
M6X65 mm Socket Screw
4” Locking Plate Caster
Upper Back Panel 1 EA
Bottom Back Panel 1EA
Electrical Mount Screw M5*7mm
Electrical Mount Screw M5*17mm
Page 2 of 15
Text on page 3
Odyssey Laptop Charging Cart
Hardware List
Phillips Magnet Screws #4 X 20mm
Page 3 of 15
Text on page 4
R EAD T HROUGH I NSTRUCTIONS FROM
BEGINNING TO END BEFORE STARTING TO ASSEMBLE UNIT .
1.) Identify and Separate all the Parts and Hardware.
2.) Attach two Locking Casters (C) to the bottom front and two Non-Locking Casters (D) to the bottom rear of Metal Base (P-1) using four Screws (A) for each caster. See Illustration #1.
2a.) Place a Grommet- Base (B) in each of the two large holes in the Metal Base (P1).
Attach one of the Side Handles (P-4) to the left side of Metal Base (P-1) using two Screws (A2) as shown in Illustration #2. Front
Page 4 of 15
Text on page 5
4.) Attach the Left Side Panel (P5) to the Side Handle (P4) using four Screws (A1) and four Tapped Rivets (G) as shown in Illustration # 3.
5.) Secure the Left Side Panel (P5) to the Metal Base (P1) using two Screws (A) as shown in Illustration # 4.
Page 5 of 15
Text on page 6
6.) Screw in two Cam Posts (I) into the embedded plastic inserts in the Left Side Panel (P5) as shown in Illustration # 5. Install two Cams (H) into the large holes in the Bottom Back Panel (P7-1). Install a Wood Dowel (J) in the center hole on the edge of the Bottom Back Panel (P7-1). With the Cam’s (H) arrows pointed at the Cam Posts (I), slide the Bottom Back Panel (P7-1) into place and turn the Cams clockwise a quarter turn to the lock position.
7.) Center the Back Frame (P8) over the two embedded threaded metal inserts in the Left Side Panel (P5) and secure with two Screws (A) as shown in Illustration # 6.
Page 6 of 15
Text on page 7
8.) Screw in two Cam Posts (I) into the embedded plastic inserts in the Left Side Panel (P5) as shown in Illustration # 5. Install two Cams (H) into the large holes in the Upper Back Panel (P7). Install a Wood Dowel (J) in the center hole on the edge of the Upper Back Panel (P7). With the Cam’s (H) arrows pointed at the Cam Posts (I), slide the Upper Back Panel (P7) into place and turn the Cams clockwise a quarter turn to the lock position.
Place two Cams (H) in the Upper Back Panel (P7) and two Cams (H) in the Bottom Back Panel (P7-1) making sure the arrows on the Cams (H) are pointe to the right as shown in Illustration # 8. Push in one Wood Dowel (J) into the edge of the Upper Back Panel (P7) and one Wood Dowel (J) into the edge of the Bottom Back Panel (P7-1). Screw in four Cam Posts (I) into the the Right Side Panel (P6). Move the Right Side Panel (P6) in to connect. Turn the Cams (H) a quarter turn to lock. Secure the Back Frame (P8) to the Right Side Panel (P6) using two Screws (A).
Page 7 of 15
Text on page 8
10.) Attach the Right Side Panel (P6) to the Side Handle (P4) using four Screws (A1) and four Tapped Rivets (G) as shown in Illustration # 9.
11.) Secure the Right Side Panel (P6) to the Metal Base (P1) using two Screws (A) as shown in Illustration # 10.
Page 8 of 15
Text on page 9
Insert two Cams (H) into the top of the Left Side Panel (P5) and one into the top left of the Upper Back Panel (P7) making sure the arrow on the Cams (H) are pointed up. Press in two Wood Dowels (J) into the top edge of the Left Side Panel (P5). Screw in three Cam Posts (I) into the bottom left of the Top Panel (P2) as shown in Illustration # 11. Repeat these same Steps to install Cams(H), Wood Dowels (J) and Cam Posts (I) into the Right Side Panel (P6), the Back Panel (P7) and under the right bottom of the Top Panel (P2). Lower the Top Panel (P2) down onto the assembly and turn the Cams a quarter turn to lock into place.
13.) Place the Back Lock (P) into the Center Back Panel (P10) from the outside and in. Use the Lock Clip (Q) on the back side of the Back Lock (P) to secure it in place. Place the bottom pegs on the Center Back Panel (P10) into the two holes in the bottom of the Back Frame (P8) and lock the Back Lock (P) to keep the Center Back Panel (P10) in place. See Illustration # 12.
Page 9 of 15
Text on page 10
14.) Install the top Shelf (P3) in between the Left Side Panel (P5) and Right Side Panel (P6) using four Screws (A) into the threaded inserts in the side panels. Repeat this Step to install the bottom Shelf as shown in illustration #13.
Attach the two Vertical Supports (P11) to the Top Panel (P2) and to the Metal Base (P1) using Screws (A) into the threaded holes as shown in Illustration #14.
Page 10 of 15
Text on page 11
16.) Attach two Door Hinges (S) to the Left Side Panel (P5) using four Hinge Screws -Wood (T) into the prdrilled locate holes for each hinge. Attach the Left Door (P12) to the Door Hinges (S) using two Hinge Screws-Metal (U) as shown in Illustration #15.
Repeat Step 18 to install the Right Door (P13) to the Right Side Panel (P6) as shown in Illustration # 16.
Page 11 of 15
Text on page 12
Attach the two Vertical Hanging Bars (P14) to the back of the two Shelves (P3) using one Electrical Mount Screw (L2) through an Electrical Mount (K) and into the threaded hole in the back flanges of the top and bottom shelves. Attach two more Electrical Mounts (K) using Electrical Mount Screws (L1) between the top an bottom Electrical Mounts on each Vertical Hanging Bar as shown in illustration #17.
Snap in four Electrical Outlet strips (M) into the Electrical Mount clips ( K) as shown in illustration #18
Page 12 of 15
Text on page 13
Install nine Tablet Dividers (R) into each of the three slots in each Shelf (P3). Secure each Tablet Divider (R) to the Shelf from underneath by snapping on a Divider Connector (V). See illustration #19.
21.) Install Magnet (X) under the Top Panel (P2) in the front center so it catches and holds the Left Door (P12) when it is closed. Use two Magnet Screws (Y) to secure. See illustration #20.
Page 13 of 15
Text on page 14
22.) Install the Electrical Tmer (Z) in the cut out at the boottom of the Right Side Panel (P6). Secure in place using four Timer Mount Screws (T1) as shown in illustration #21.
Page 14 of 15
Text on page 15
Odyssey High Capacity Charging Cart
Shelf is 13 3/4” Deep
10 5/8” Clear
10 5/8” Clear
33” Clear
10 5/8” Clear
WWW.MYBINDING.COM
Page 15 of 15 ยท End of manual
Quick start
- Identify and separate all parts and hardware.
- Attach two Locking Casters (C) to the front and two Non-Locking Casters (D) to the rear of the Metal Base (P-1), add the base grommets and attach the Side Handles (P-4).
- Fit the Left Side Panel, then join the Bottom and Upper Back Panels, Right Side Panel and Top Panel with Cams (H), Cam Posts (I) and Wood Dowels (J), turning each cam a quarter turn to lock.
- Install the Center Back Panel (P10) with its Back Lock (P), then fix the top and bottom Shelves (P3) with four Screws (A) each and add the Vertical Supports (P11).
- Hang the Left and Right Doors on their hinges.
- Attach the two Vertical Hanging Bars (P14) with Electrical Mounts (K) and snap in the four Electrical Outlet Strips (M).
- Install nine Tablet Dividers (R) in each of the three slots per shelf, add the door Magnet (X), and mount the Electrical Timer (Z) in the right side panel cut-out with four screws.
Frequently asked questions
How deep are the shelves in the Odyssey High Capacity cart?
The shelves are 13 3/4" deep, with 10 5/8" of clearance in each of the shelf bays and 33" of clearance in the tall section. See page 15.
How many tablet dividers does each shelf take?
Nine dividers in each of the three slots in each shelf, locked from underneath with Divider Connectors. See page 13.
How many outlet strips are installed?
Four electrical outlet strips, snapped into mounts on two vertical hanging bars. See page 12.
Where does the timer go?
In the cut-out at the bottom of the Right Side Panel (P6), secured with four Timer Mount Screws (T1). See page 14.
