Page 1 of 12
Page 2 of 12
Text on page 3
Mobile 20 Tub Storage Cart
Hardware List
CS Phil Screw M6X50mm
CS Wd Screw M3x12mm
Phil Pan Screw M4x12mm
Pan Hd Screw M4x18mm
CS Wood Screw M3x8mm
Page 3 of 12
Text on page 4
Hardware List
¼” Phil Head Lock Screw
Page 4 of 12
Text on page 5
Assembly Diagram
To Assemble:
- Identify and Separate all the Parts and Hardware.
- Attach Right Leg Welded (P2) to the Top and
bottom Panels (P4 & P5) using 6 screws (A1) as shown in illustration #1.
- Attach Back Panel (P6) to the Right Leg
Welded (P2)using 3 screws (A1) as shown in illustration #1.
Page 5 of 12
Text on page 6
- Attach the Back Panel P6) to P4
the Bottom Panel (P5) using one Screw (A2).
TOP
- Insert Slotted End Panel (P3) in
the Right Leg Welded as shown in illustration #3. Make sure the four predrilled holes are under the fifth slot from the top.
- Insert 9 Wood Dowels (B1) in
holes in the Back Panel (P6).
Page 6 of 12
Text on page 7
Attach two Middle Shelf Brackets (J) to the bottom sides of the Middle Shelf (P11) using 2 CS Wood Screws (A5) as shown in illustration #4A.
- Place Middle Shelf assembly, from Step 8, in the fourth slot down from th the top of Slotted End Panel (P3). Use 2 CS Screws (A5) to attach through the Middle Shelf Bracket (J) and into the Slotted End Panel’s(P3) predrilled holes as shown in illustration #4B.
Page 7 of 12
Text on page 8
- Slide 8 Shelves (P7) over Dowels (B1) and into slots in Slotted End Panel (P3) as shown in illustration # 4C.
- Place Slotted End Panel (P3) over the end of 9 Shelves (P7) as shown in illustration #5.
- Attach Left Leg Welded (P1)
to the Top and bottom Panels (P4 & P5) using 6 screws (A1) .
- Attach the Left Leg Welded
(P1) to the Back Panel (P6) using 3 screws (A1) as shown in illustration #5.
Page 8 of 12
Text on page 9
- Attach 2 Locking Casters (D), and 2 Lock Washers (C) to
the front of Welded Legs (P1 & P2).
- Attach 2 Casters (E) and 2 Lock Washers (C)
to the back of Welded Legs (P1 & P2). Tighten all Casters using Caster Wrench (N). Attach Bracket (J) that is under Middle Shelf (P11) to left (P3) End Panel using 2 CS Screws (A5) as shown in detail.
DETAIL
- Place the Right Door (P8) with the
Predrilled holes (for hinges) facing up and Insert 1 each Lock Cylinder (K1) through the hole in the Door (P8) as shown in illustration #7.
- Secure Lock Cylinder (K1) using the Lock Washer (K2) and the Lock Hex (K3). (F INGER T IGHTEN O NLY .)
- Slide Lock Retainer (K4) over the square end of Lock Cylinder (K1). Secure using the ¼” Phil Head Lock Screw (K5).
- Attach 1 Door Handle (F)
to the Door (P8) using 2 Screws (A4).
Page 9 of 12
Text on page 10
- Attach the Right Door (P10) to the Right Leg Welded (P2) using three CS Wood Screws (A3) through each Door Hinge as shown in illustration # 8b.
- Before tightening the Lock Hex (K3), Insert the Key (L) and turn lock. Be sure that Lock Retainer (K4) turns 90 degrees and rotates behind Door Stop on the Left Leg Welded (P1). T IGHTEN L OCK H EX (K3).
Page 10 of 12
Text on page 11
- Attach the Metal Plate (S) to the front of the Door (P8) using one CS Wood Screw (A6) in the predrilled hole in the Door. Attach the Magnet (R) to the Right Leg Welded (P2) using two Screws (A5) into the predrilled holes near the top of the Leg. See illustration # 9.
- Push in four Tube Closures (Q) into the top tubes of the Right and Left Legs. See illustration #9
Page 11 of 12
Page 12 of 12 ยท End of manual
Quick start
- Identify and separate all parts and hardware.
- Attach the Right Leg Welded (P2) to the Top and Bottom Panels (P4 and P5) with 6 screws (A1), then attach the Back Panel (P6) to the leg with 3 screws (A1) and to the bottom panel with one Screw (A2).
- Insert a Slotted End Panel (P3) in the right leg with the four predrilled holes under the fifth slot from the top, and press 9 Wood Dowels (B1) into the back panel.
- Fit the Middle Shelf Brackets (J) to the Middle Shelf (P11), set it in the fourth slot from the top and screw it to the end panel; slide the 8 Shelves (P7) over the dowels into the slots.
- Place the second Slotted End Panel over the shelf ends and attach the Left Leg Welded (P1) to the top, bottom and back panels.
- Attach 2 Locking Casters (D) at the front and 2 Casters (E) at the back, each with a Lock Washer (C), and tighten with the Caster Wrench (N).
- Fit the Lock Cylinder (finger tight only), Lock Retainer and Door Handle (F) to the door, hang it with three screws (A3) per hinge, check the retainer turns 90 degrees behind the door stop, then tighten the Lock Hex. Add the Metal Plate, Magnet and Tube Closures.
Frequently asked questions
How many shelves does the 27754 cart use?
One Middle Shelf (P11) fixed with brackets plus 8 slide-in Shelves (P7). See page 7 and page 8.
Which slot does the middle shelf go in?
The fourth slot down from the top of the Slotted End Panel. See page 7.
How do I make sure the door lock works?
Finger-tighten the Lock Hex at first. After hanging the door, insert the key and turn it to confirm the Lock Retainer rotates 90 degrees behind the door stop on the left leg, then tighten the Lock Hex. See page 10.
