Balt 4' x 6' Black Enlighten Glass Dry-Erase Whiteboard Instruction Manual, page 1

Page 1 of 6

Balt 4' x 6' Black Enlighten Glass Dry-Erase Whiteboard Instruction Manual, page 2

Page 2 of 6

Balt 4' x 6' Black Enlighten Glass Dry-Erase Whiteboard Instruction Manual, page 3
Text on page 3

EEnlighten Board

Hardware Chart by Board Size 2’X3’ GBoard - 4 pcs. (A), (B) 4 pcs. (C), (D),(E) 4 pcs. (F) 3’X4’ GBoard - 4 pcs. (A), (B) 4 pcs. (C), (D), (E) 4 pcs. (F) 4’X6’ GBoard - 6 pcs. (A), (B) 6 pcs. (C), (D), (E) 6 pcs. (F) 1’ X1’ GBoard- 4 pcs. (A),(B) 4 pcs. (C), (D), (E) 4 pcs. (F) 1.5” X 2’ GBoard- 4 pcs. (A), (B) 4 pcs. (C), (D), (E) 4 pcs. (F) 20” X 30” GBoard-4 pcs. (A),(B) 4 pcs. (C), (D), (E) 4 pcs. (F)

See Chart

See Chart

See Chart

See Chart

See Chart

See Chart

Special Note:

Your new glass board requires a flat wall for mounting. Make sure the area behind the glass board is free of any high spots.

Page 3 of 6

Balt 4' x 6' Black Enlighten Glass Dry-Erase Whiteboard Instruction Manual, page 4
Text on page 4

stallPreparing to Install Your New Enlighten Board

Measure the length and width of your new board. Determine the wall center line and height off the floor that you want your new board to be located. Hold your board up in position and draw a line under the bottom of the board and parallel with the floor. If your wall has studs, determine the centerline of the studs. It is recommended that you tie into as many studs as possible when mounting your board. .

NOTE: The proper installation of your board will require at least two people. Tools required: Tape measure, chalkline, electric drill / screwdriver, drill and screwdriver bits, stud finder and level. .

2.) When you have your glass board positioned, mark the wall through the mount holes that are in the board.

Page 4 of 6

Balt 4' x 6' Black Enlighten Glass Dry-Erase Whiteboard Instruction Manual, page 5
Text on page 5

Installing the Glass Board

3.) After you have followed the guidelines from Page 3, install the correct number of wall anchors for the size board you are mounting to the wall. Install the anchors as shown in Illustration #3A and #3B.

3A.) For all walls except sheet rock:

. . Predrill a 5/16” diameter hole in the center of each of your marked mount holes. Push in a Plastic Anchor (C) into each predrilled hole. Repeat this Step for each anchor that is required for your size board. .

5/16” Predrilled Hole

. . Predrill a 1/4” diameter hole in the center of each of your marked holes. Screw in a Drywal l Anchor

  1. in the center of each of the marked mount holes. Repeat this Step for each anchor that is required for your size board.

3B.) For sheet rock walls:

1/4”” Predrilled Hole

Page 5 of 6

Balt 4' x 6' Black Enlighten Glass Dry-Erase Whiteboard Instruction Manual, page 6
Text on page 6

To attach your Glass Board (P1) to the wall, use a Screw (D) through a Brass Mount (B), a Plastic Washer (F) ,through the hole in the board and into the wall anchor as shown in illustration # 4. Repeat this Step for each mounting hole in your board.

5.) Screw an Outer Cap (A) onto each Brass Mount (B) as shown in illustration # 5. Repeat this Step for each mount on your board.

WWW.MYBINDING.COM

Page 6 of 6 · End of manual

Quick start

  1. Gather a tape measure, chalk line, electric drill/screwdriver, drill and screwdriver bits, stud finder and level. Plan on at least two people, and make sure the wall is flat with no high spots behind the board.
  2. Choose the board's center line and height, hold it in place and draw a level line under its bottom edge. Locate studs and tie into as many as possible.
  3. With the board positioned, mark the wall through the mount holes in the glass.
  4. For walls other than sheet rock, predrill a 5/16" hole at each mark and push in a plastic anchor (C). For sheet rock, predrill 1/4" and screw in a drywall anchor.
  5. Attach the glass board (P1) with a screw (D) through a brass mount (B), a plastic washer (F) and the hole in the board into each anchor.
  6. Screw an outer cap (A) onto each brass mount.

Frequently asked questions

How many mounts does the 4' x 6' Enlighten board use?

The hardware chart lists 6 each of the outer caps and brass mounts (A, B), the anchors and screws (C, D, E) and the plastic washers (F) for the 4' x 6' board. See page 3.

What size holes do I drill for the anchors?

Predrill 5/16" for plastic anchors in walls other than sheet rock, and 1/4" for drywall anchors in sheet rock. See page 5.

How many people does installation take?

The instructions say proper installation requires at least two people. See page 4.

Does the wall need to be flat?

Yes. The glass board requires a flat wall, and the area behind it must be free of high spots. See page 3.