Page 1 of 6
Page 2 of 6
Text on page 3
EEnlighten Board
Hardware Chart by Board Size 2’X3’ GBoard - 4 pcs. (A), (B) 4 pcs. (C), (D),(E) 4 pcs. (F) 3’X4’ GBoard - 4 pcs. (A), (B) 4 pcs. (C), (D), (E) 4 pcs. (F) 4’X6’ GBoard - 6 pcs. (A), (B) 6 pcs. (C), (D), (E) 6 pcs. (F) 1’ X1’ GBoard- 4 pcs. (A),(B) 4 pcs. (C), (D), (E) 4 pcs. (F) 1.5” X 2’ GBoard- 4 pcs. (A), (B) 4 pcs. (C), (D), (E) 4 pcs. (F) 20” X 30” GBoard-4 pcs. (A),(B) 4 pcs. (C), (D), (E) 4 pcs. (F)
See Chart
See Chart
See Chart
See Chart
See Chart
See Chart
Special Note:
Your new glass board requires a flat wall for mounting. Make sure the area behind the glass board is free of any high spots.
Page 3 of 6
Text on page 4
stallPreparing to Install Your New Enlighten Board
Measure the length and width of your new board. Determine the wall center line and height off the floor that you want your new board to be located. Hold your board up in position and draw a line under the bottom of the board and parallel with the floor. If your wall has studs, determine the centerline of the studs. It is recommended that you tie into as many studs as possible when mounting your board. .
NOTE: The proper installation of your board will require at least two people. Tools required: Tape measure, chalkline, electric drill / screwdriver, drill and screwdriver bits, stud finder and level. .
2.) When you have your glass board positioned, mark the wall through the mount holes that are in the board.
Page 4 of 6
Text on page 5
Installing the Glass Board
3.) After you have followed the guidelines from Page 3, install the correct number of wall anchors for the size board you are mounting to the wall. Install the anchors as shown in Illustration #3A and #3B.
3A.) For all walls except sheet rock:
. . Predrill a 5/16” diameter hole in the center of each of your marked mount holes. Push in a Plastic Anchor (C) into each predrilled hole. Repeat this Step for each anchor that is required for your size board. .
5/16” Predrilled Hole
3B.) For sheet rock walls:
. . Predrill a 1/4” diameter hole in the center of each of your marked holes. Screw in a Drywal l Anchor
- in the center of each of the marked mount holes. Repeat this Step for each anchor that is required for your size board.
1/4”” Predrilled Hole
Page 5 of 6
Text on page 6
To attach your Glass Board (P1) to the wall, use a Screw (D) through a Brass Mount (B), a Plastic Washer (F) ,through the hole in the board and into the wall anchor as shown in illustration # 4. Repeat this Step for each mounting hole in your board.
5.) Screw an Outer Cap (A) onto each Brass Mount (B) as shown in illustration # 5. Repeat this Step for each mount on your board.
WWW.MYBINDING.COM
Page 6 of 6 · End of manual
Quick start
- Make sure the wall is flat and free of high spots behind the board.
- Measure the board, choose the wall center line and height, and with a helper hold the board in place and draw a line under its bottom edge, parallel with the floor. Tie into studs where possible.
- Mark the wall through the mount holes in the board.
- For walls other than sheet rock, drill a 5/16" hole at each mark and push in a Plastic Anchor (C). For sheet rock, drill a 1/4" hole and screw in a Drywall Anchor.
- Attach the Glass Board (P1) with a Screw (D) through a Brass Mount (B), a Plastic Washer (F) and the board hole into each anchor.
- Screw an Outer Cap (A) onto each brass mount.
Frequently asked questions
How many mounts does my Enlighten board size need?
The 4'x6' board uses 6 sets of mounting hardware. The 1'x1', 1.5'x2', 20"x30", 2'x3' and 3'x4' boards use 4 sets. See page 3.
What size holes do I drill for the anchors?
5/16" holes with Plastic Anchors for most walls, or 1/4" holes with Drywall Anchors for sheet rock. See page 5.
How many people and what tools are needed?
At least two people, plus a tape measure, chalkline, electric drill/screwdriver, drill and screwdriver bits, stud finder and level. See page 4.
What kind of wall does the board need?
A flat wall with no high spots behind the board. See page 3.
