Page 1 of 9
Page 2 of 9
Text on page 3
WOW
Hardware List
(NOT INCLUDED)
Page 3 of 9
Text on page 4
Assembly Diagram
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING
TO END BEFORE STARTING TO ASSEMBLE UNIT .
1.) Identify and Separate all the Parts and Hardware.
2.) Place the LCD Platform (P-3) with the insert nuts facing up. Attach 1 Right Leg Assembly (P-1) and 1 Left Leg Assembly (P-2) using 4 each (A) screws. (Finger tighten only)
3.) Attach Stability Panel (P-7) to Right & Left Leg Assemblies (P-1 & P-2) using 4 (A) Screws as shown in illustration #1. (Finger tighten only)
Page 4 of 9
Text on page 5
4.) Align 4 each Angle Brackets (P-8) with the edge of the Middle Shelf (P-6) and attach using 4 each (A) Screws as shown in illustration #2. (Finger tighten only)
5.) Attach Right Shelf Bracket (P-9) and
Left Shelf Bracket (P-10) to Laptop Shelf (P-4) using 4 Flat Head screws (A) as shown in illustration # 4.
Page 5 of 9
Text on page 6
6.) Attach Lower Shelf (P-5) to the Right & Left Leg Assemblies (P1 & P2) using 4 each (B) screws as shown in illustration # 4. (Finger tighten only)
7.) Attach 2 Locking Casters (D-1) to the front of the unit. Attach 2 Casters (D-2) to the back of the unit. Tighten all Casters using Caster Wrench (G).
8.) Slide Middle Shelf (P-6) Between Right & Left Leg Assemblies (P-1 & P-2) and attach Middle Shelf (P-6) using 4 each (A) screws and 4 each (C) Square Nuts as shown in illustration # 4. Secure Middle Shelf (P-6) to Stability Panel (P-7) using two screws (A).
9.) (Tighten all the screws at this time using Allen Wrench (F)).
Page 6 of 9
Text on page 7
10.) To install Grommets (E) in LCD Platform (P-3) and Middle Shelf (P-6), separate parts and press Grommet Sleeve in opening as shown in illustration # 5.
11.) Snap a plastic Cap into the top of each Sleeve as shown in illustration # 5.
12.)Hook the Right Shelf Bracket (P-9) and Left Shelf Bracket (P-10) into the Right & Left Leg Assemblies at the desired height as shown in illustration # 5.
Important
The product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal use due to defect or imperfection, the defective part or product will be replaced. Damage caused by common carriers during shipment is not included in this guarantee.
This guarantee sets forth all applicable guarantees and remedies. No other warranty, expressed or implied shall apply. Failure to follow instructions found in Important Information Section of Owner Sheet shall void the guarantee. Consequential or incidental damages and or costs are not refundable.
Page 7 of 9
Text on page 8
Optional Electric Outlet
Assembly Diagram
Metal Bracket w/Cord Winder
(NOT INCLUDED)
1.) Identify and Separate all the Parts and Hardware.
2.) Slide Metal Bracket over the Electrical
Outlet (EL-1) as shown. (note that Metal Stop is at the end with the electrical Plugin.)
Attach Metal Bracket (EL-2) to the Right or Left Leg Assembly (P-1 or P-2) using 2 Phillips Head Screws (EL-3) and 2 Hex Nuts (EL-4) as shown in Optional EL-2 Electrical illustration.
Metal Stop
Electrical Plug-in
Optional Electrical Illustration
Page 8 of 9
Text on page 9
Presentation Cart
#66450 Optional Electrical Outlet
Adjustable Height 19” - 39-½”
Middle Shelf 15 3/4” X 15 1/2”
Shipping Information 0.2 Cubic Feet 4.0 lbs.
Shipping Information 2.86 Cubic Feet 49 lbs.
#66450 electric Outlet
#89759 Presentation Cart
WWW.MYBINDING.COM
Page 9 of 9 · End of manual
Quick start
- Identify and separate all parts and hardware.
- Place the LCD Platform (P-3) insert nuts up and attach the Right and Left Leg Assemblies with 4 screws (A), then the Stability Panel (P-7) with 4 screws (A). Finger tighten only.
- Fix 4 Angle Brackets (P-8) to the Middle Shelf (P-6), and the Right and Left Shelf Brackets (P-9, P-10) to the Laptop Shelf (P-4).
- Attach the Lower Shelf (P-5) with 4 screws (B), then 2 Locking Casters (D-1) at the front and 2 Casters (D-2) at the back; tighten with the Caster Wrench (G).
- Slide the Middle Shelf between the legs, secure with 4 screws (A) and 4 Square Nuts (C) plus two screws into the stability panel, then tighten all screws with Allen Wrench (F).
- Press the Grommets (E) into the LCD platform and middle shelf and snap on the caps.
- Hook the laptop shelf brackets into the leg assemblies at the height you want.
Frequently asked questions
What is the height adjustment range of the 89759 cart?
19" to 39 1/2". See page 9.
How big is the middle shelf?
15 3/4" x 15 1/2". See page 9.
Is an electrical outlet included?
No. The #66450 electric outlet is optional and not included. It mounts to either leg with a metal bracket and cord winder. See page 8.
How do I change the laptop shelf height?
Hook the Right and Left Shelf Brackets into the leg assemblies at the height you want. See page 7.
