Page 1 of 8
Text on page 2
WOW
DIVERSITY STAND
Adjustable Height Presentation Center
Hardware List
Wrench for acorn nuts
Page 2 of 8
Text on page 3
Diversity Stand
Assembly Diagram
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING
TO END BEFORE STARTING TO ASSEMBLE UNIT .
We recommend that you assemble this unit on a table.
1.) Identify and Separate all the Parts and Hardware.
2.) Place the Shelf Platform (P7) with the insert nuts facing up. Attach 1 each Left Leg Receiver (P5) and 1 each Right Leg Receiver (P6) using 4 each (A) screws.
3.) Attach 1 each Back Panel (P8) using 3 each (A) screws as shown in illustration #1. (Finger tighten only)
- Screw M6 X 1/2” For Scale only
- Square Nut M6 For Scale only
4.) Attach 4 Locking casters (D) in the front and back as shown in illustration #1. Tighten the Casters using Caster Wrench (K).
5.) Attach Bottom Panel (P9) between the Left Leg Receiver (P5) and Right Leg Receiver (P6) using 7 Screws
- and 7 Square Nuts (B) as shown in illustration #2.
Do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorized parts.
Page 3 of 8
Text on page 4
6.) Attach Wire Rail (P-13) to the Shelf Platform (P-7) using 4 Acorn Nuts(A4) as shown in illustration #3.
(C)Acorn Nut For Scale only
Tighten Acorn Nuts (C) using Wrench(L).
7.) Attach 2 each Hinges(H) to the LCD Platform (P-1) and the Tilt Platform (P2) using 12 Screws (A3).
8.) Attach 1 Left Tilt Support Bracket (P-10) and 1 Right Tilt Support Bracket (P-11) to the Tilt Platform (P-2) using 6 Screws (A3) as shown in illustration #4.
9.) Attach Paper Stop (P-16) to the Tilt Platform (P-2) using 2 Screws (A) as shown in illustration #4.
- Screw M6 X 1/2” For Scale only
(A3) Screw #4 X 5/8”
Page 4 of 8
Text on page 5
(A2) Screw M6 X 2” For Scale only
10.) Place the LCD Platform (P1) with the insert nuts facing up. Attach 1 Left Upper Insert (P-3) and 1 Right Upper Insert (P-4) to the LCD Platform (P-1) using 4 Screws (A2) as shown in illustration #5.
11.) Slide Tilt Support Arm (P-12) through Left Tilt Support Bracket (P-10) and Right Tilt Support Bracket (P-11) as shown in illustration #5.
12.) Rotate Tilt Support Arm (P-12) and attach to 1 Left Upper Insert (P-3) and 1 Right Upper Insert (P-4) using 2 Screws (A1), 2 Flat Washers (F), and 2 Interior Threaded Posts (B1) as shown in illustration #6.
(A1) Screw M6 X 1-1/2” For Scale only
- Flat Washer For Scale only
(B1) Interior Threaded Post M6 X 9/16” For Scale only
Page 5 of 8
Text on page 6
Missing Parts or UPS Damaged Parts For Your Convenience you can EMAIL us at
Should you require assistance during assembly, please call our Customer Service Department Monday - Friday 8 a.m. - 5 p.m. Central Standard Time 1-800-749-2258
24HOURS 7 DAYS A WEEK
13.) Insert Left Upper Insert (P-3) and Right Upper Insert (P-4) into the Left Leg Receiver (P5) and Right Leg Receiver (P6) as shown in illustration #4. Secure at desired height using 4 Knobs(G)
Page 6 of 8
Text on page 7
14.) Attach 1 wire LCD Front Rail (P10) to the Front of the LCD Platform (P1) using 2 Acorn Nuts (C) as shown in illustration #7.
15.) Attach 2 wire LCD SideRail (P11) to the sides of the LCD Platform (P1) using 4 Acorn (C) as shown in illustration #7.
Tighten all the screws at this time using Allen Wrench (K).
(C)Acorn Nut For Scale only
Tighten Acorn Nuts (C) using Wrench(L).
Important
The Balt product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal use due to defect or imperfection, the defective part or product will be replaced. Damage caused by common carriers during shipment is not included in this guarantee.
This guarantee sets forth all applicable guarantees and remedies. No other warranty, expressed or implied shall apply. Failure to follow instructions found in Important Information Section of Owner Sheet shall void the guarantee. Consequential or incidental damages and or costs are not refundable.
Page 7 of 8
Text on page 8
#89786 Diversity Stand
Adjustable Height Presentation Center
Adjustable Height 11-19”
Adjustable Height 37 ½ - 45 ½
Shipping Information 4.0 Cubic Feet 48 lbs.
5 Positions 0 to 35º
WWW.MYBINDING.COM
Page 8 of 8 · End of manual
Quick start
- Assemble on a table. Identify and separate all parts and hardware.
- Place the Shelf Platform (P7) insert nuts up, attach the Left and Right Leg Receivers with 4 screws (A), and attach the Back Panel (P8) with 3 screws (finger tight).
- Attach the 4 Locking Casters (D) and tighten with the Caster Wrench (K), then fit the Bottom Panel (P9) with 7 screws and 7 Square Nuts (B).
- Attach the Wire Rail (P-13) to the shelf platform with Acorn Nuts, tightened with Wrench (L).
- Join the LCD Platform (P-1) and Tilt Platform (P-2) with 2 Hinges (H), then add the tilt support brackets and Paper Stop (P-16).
- Attach the Upper Inserts to the LCD platform, slide the Tilt Support Arm (P-12) through the brackets and fix it to the inserts.
- Insert the upper inserts into the leg receivers and set the height with the 4 Knobs (G). Add the LCD front and side wire rails, then tighten all screws.
Frequently asked questions
What height range does the Diversity Stand offer?
The spec sheet lists adjustable heights of 11"-19" and 37 1/2"-45 1/2". See page 8.
How far does the tilt platform tilt?
It has 5 positions from 0 to 35 degrees. See page 8.
Do all the casters lock?
Yes. The stand uses 4 Locking Casters (D), front and back. See page 3.
Who do I contact for help or missing parts?
Customer Service at 1-800-749-2258, Monday to Friday, 8 a.m. to 5 p.m. Central. See page 6.
