Page 1 of 6
Page 2 of 6
Text on page 3
Adjustable Height Utility Stand
Screw M6X12mm Pan Hd
Screw M5X45mm Pan Hd
Hex nut M5 w/Flange
Lock Washer Ext Tooth
Missing Parts or UPS Damaged Parts For Your Convenience you can EMAIL us at
24HOURS 7 DAYS A WEEK
Should you require assistance during assembly, please call our Customer Service Department Monday - Friday 8 a.m. - 5 p.m. Central Standard Time 1-800-749-2258
Do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorized parts.
Page 3 of 6
Text on page 4
#89842
Assembly Diagram
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING TO
END BEFORE STARTING TO ASSEMBLE UNIT .
1.) Identify and Separate all the Parts
2.) Slide Welded Top Shelf (P-1) over the Welded Base (P-2) and secure at desired height using 8 Screws (A), 8 Lock Washers with Teeth (C), and 8 M6 Hex Nuts (B).
3.) Attach Cord Winder (P-5) and Electrical Strip (P-6) using 2 screws (A2) and two M5 Hex Nuts with Shoulder (B2).
4.) Lay the Non-Slip Mat (P-4) atop the Welded Top Shelf (P-1). 5.) Tighten all screws using Phillip’s head screwdriver (Not Provided).
WWW.MYBINDING.COM
Page 4 of 6
Text on page 5
6.) Press in both locking and non-locking casters (D and E) into the factory installed nylon inserts in the Welded Base (P-2).
Important
The Balt product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal use due to defect or imperfection, the defective part or product will be replaced. Damage caused by common carriers during shipment is not included in this guarantee.
This guarantee sets forth all applicable guarantees and remedies. No other warranty, expressed or implied shall apply. Failure to follow instructions found in Important Information Section of Owner Sheet shall void the guarantee. Consequential or incidental damages and or costs are not refundable.
Page 5 of 6
Text on page 6
4.) Loosen the Hex Nuts on each side of the Pull-Out Shelf (P-3) and adjust the mounting brackets to fit on the inside vertical supports of Top Shelf (P-1).
5.) Tilt the Pullout Shelf (P-3) and slide it in the cart. Attach Pullout Shelf (P-3) to Top Shelf (P-1) using 8 screws (A1) and 8 Hex Nuts (B1) as shown in Detail 3A.
Should you require assistance during assembly, please call our Customer Service Department Monday - Friday 8 a.m. - 5 p.m. Central Standard Time 1-800-749-2258
Page 6 of 6 · End of manual
Quick start
- Identify and separate all parts.
- Slide the Welded Top Shelf (P-1) over the Welded Base (P-2) and secure it at the height you want with 8 Screws (A), 8 Lock Washers with Teeth (C) and 8 M6 Hex Nuts (B).
- Attach the Cord Winder (P-5) and Electrical Strip (P-6) with 2 screws (A2) and two M5 Hex Nuts with Shoulder (B2).
- Lay the Non-Slip Mat (P-4) on the top shelf and tighten all screws with a Phillips head screwdriver (not provided).
- Press the locking and non-locking casters (D, E) into the factory-installed nylon inserts in the base.
- Loosen the hex nuts on the Pull-Out Shelf (P-3), adjust its brackets to fit inside the top shelf's vertical supports, tilt it into the cart and attach with 8 screws (A1) and 8 Hex Nuts (B1).
Frequently asked questions
How is the height of the 89842 stand adjusted?
The welded top shelf slides over the welded base and is fixed at the height you want with 8 screws, lock washers and M6 hex nuts. See page 4.
What tools are needed?
A Phillips head screwdriver, which is not provided. See page 4.
Who can help if parts are missing?
Call Customer Service at 1-800-749-2258, Monday to Friday, 8 a.m. to 5 p.m. Central. See page 3.
