Page 1 of 6
Text on page 2
Which board assembly instructions should you use?
Use L-Clip instructions for...
Use Z-Clip instructions for...
Scroll down for instructions.
Page 2 of 6
Text on page 3
Z Clip Install Instructions
Top Edge of Board
a Bo
oc rd L
atio
Note: Install Masonry Anchors (D) into 1/4” Diameter predrill holes for masonry walls.
Install Drywall Anchors (E) into 1/4” Diameter predrill holes for sheet rock walls.
Lift, Tilt, and Slide Board down over the Z-Hangers. Z-Hangers should catch in the top trim on the back of the board. Draw line along bottom edge of board.
Bo
oc rd L
atio
Bottom Edge of Board
Determine board location. Measure from floor to the top edge of board. Mark with pencil line the corner location. Measure down from top edge of board 3/4”, and draw line as shown. Locate stud near each end of board and drill pilot hole along line using 1/8” drill bit.
Bo
ard
a Loc
tion
Z Brackets hang in the trim on back of board
Lift and remove board from the Z-Hangers. Measure up from bottom line of board 1-1/8”, and draw line as shown. Locate stud near each end of board and drill pilot hole along line using 1/8” drill bit.
Attach Z-Hangers (E) using Long Screws (A) as shown.
- Secure 2 bottom brackets (F) to the wall using 2
long screws (A) as shown. Hang board on the Z-Hangers (E).
- Secure board to bottom
Screw Anchor - Concrete (For Concrete walls)
Screw Anchor - Drywall (For Drywall)
brackets (F) using 2 short screws (B) as shown.
Z Clip Install
Page 3 of 6
Text on page 4
L Clip Install Instructions
Bo
ard
Loc
n atio
Note: Install Masonry Anchors (D) into 1/4” Diameter predrill holes for masonry walls.
Install Drywall Anchors (E) into 1/4” Diameter predrill holes for sheet rock walls.
Top Edge of Board
Bo
Bottom Edge of Board
1 Determine board location. Measure from floor to
the bottom edge of board. Mark with pencil line the corner location. Measure up from bottom edge of board 1-1/4” and draw line as shown. Locate stud near each end of board and drill pilot holes along line using 1/8” drill bit. See diagram below.
Edge of Board
Bo
L ard
oca
16” min. 3” 24” max.
Angle Bracket
Edge of Board
oca
tion
tion
Equally Spaced
Angle Bracket Locations on Board
L ard
3 Set board on the Angle
Lift and remove board from the angle brackets. Measure down from top line of board 1” and draw line as shown. Locate stud near each end of board and drill pilot hole along line using 1/8” drill bit.
Brackets. Draw line along top edge of board.
½ the # of Angle Brackets using
2 Attach
Long Screws (B) as shown.
L Clip Install
5 Secure top Angle Brackets (A) to the wall using 6
long screws (B) as shown. Follow diagram in
- Set board on the bottom angle brackets.
Secure board to bottom and top brackets (A) using short screws (C) as shown.
Page 4 of 6
Text on page 5
Attention
Please read and follow these instructions! Failure to follow these instructions will void your warranty and could result in board failure and possible injury.
- Always use the correct supplied mounting hardware for the type wall your board will be mounted on.
- Use the correct stated predrill for the type anchor you will be using.
- The Angle Brackets and Z Clips MUST be installed according to the layout and spacing as shown below.
NOTE: For more information, please refer to our web-site: www.partsandinstructions.com
WWW.MYBINDING.COM
Page 5 of 6
Text on page 6
Proper L-Clip Layout
Your top and bottom L-Clip layouts should be spaced like this for an 8’ wide board.
If you don’t use this number of L-Clips on top and bottom, your board could end up like this. Please follow these installation directions.
Page 6 of 6 · End of manual
Quick start
- Check which method your board uses (L-Clip or Z-Clip) and use the matching instructions. Use the masonry anchors for masonry walls or the drywall anchors for sheet rock, each in a 1/4" predrilled hole.
- Z-Clip: Measure from the floor to where the top edge of the board will sit and mark it. Draw a line 3/4" below that mark, find a stud near each end and drill pilot holes on the line with a 1/8" bit.
- Z-Clip: Attach the Z-hangers with the long screws. Lift, tilt and slide the board down over the hangers so they catch in the top trim on the back, then draw a line along the bottom edge.
- Z-Clip: Lift the board off, draw a line 1-1/8" above the bottom line and drill pilot holes. Fasten the 2 bottom brackets with long screws, hang the board on the Z-hangers and secure it to the bottom brackets with 2 short screws.
- L-Clip: Measure from the floor to where the bottom edge of the board will sit and mark it. Draw a line 1-1/4" above it and drill 1/8" pilot holes at studs near each end.
- L-Clip: Attach half of the angle brackets along the bottom line with the long screws, equally spaced as shown in the bracket layout diagram. Set the board on them and draw a line along its top edge.
- L-Clip: Lift the board off, draw a line 1" below the top line, drill pilot holes and fasten the top angle brackets with long screws. Set the board on the bottom brackets and secure it to the bottom and top brackets with the short screws.
Frequently asked questions
Can the Best-Rite 302PB be mounted on drywall or concrete?
Yes. The kit includes masonry anchors for masonry walls and drywall anchors for sheet rock walls. Install either type in a 1/4" predrilled hole, and always use the supplied hardware that matches your wall type (page 3).
What size drill bit do I need for the pilot holes?
Pilot holes at the wall studs are drilled with a 1/8" bit. Holes for the masonry or drywall anchors are predrilled at 1/4" diameter (page 4).
What is the difference between L-Clip and Z-Clip mounting?
With Z-Clips, Z-hangers on the wall catch in the top trim on the back of the board, and 2 bottom brackets hold the lower edge (page 3). With L-Clips, angle brackets are fastened along both the bottom and top edges and the board is screwed to each one (page 4).
Does it matter how many L-Clips I use?
Yes. The angle brackets and Z-Clips must be installed in the layout and spacing shown. The manual shows the correct top and bottom L-Clip layout for an 8' wide board and warns that using fewer clips can lead to board failure (page 6).
Will installing the board incorrectly affect the warranty?
Yes. Not following these instructions voids the warranty and could result in board failure and possible injury (page 5).
