Page 1 of 6
Text on page 2
Which board assembly instructions should you use?
Use L-Clip instructions for...
Use Z-Clip instructions for...
Scroll down for instructions.
Page 2 of 6
Text on page 3
Z Clip Install Instructions
Top Edge of Board
a Bo
oc rd L
atio
Note: Install Masonry Anchors (D) into 1/4” Diameter predrill holes for masonry walls.
Install Drywall Anchors (E) into 1/4” Diameter predrill holes for sheet rock walls.
Lift, Tilt, and Slide Board down over the Z-Hangers. Z-Hangers should catch in the top trim on the back of the board. Draw line along bottom edge of board.
Bo
oc rd L
atio
Bottom Edge of Board
Determine board location. Measure from floor to the top edge of board. Mark with pencil line the corner location. Measure down from top edge of board 3/4”, and draw line as shown. Locate stud near each end of board and drill pilot hole along line using 1/8” drill bit.
Bo
ard
a Loc
tion
Z Brackets hang in the trim on back of board
Lift and remove board from the Z-Hangers. Measure up from bottom line of board 1-1/8”, and draw line as shown. Locate stud near each end of board and drill pilot hole along line using 1/8” drill bit.
Attach Z-Hangers (E) using Long Screws (A) as shown.
- Secure 2 bottom brackets (F) to the wall using 2
long screws (A) as shown. Hang board on the Z-Hangers (E).
- Secure board to bottom
Screw Anchor - Concrete (For Concrete walls)
Screw Anchor - Drywall (For Drywall)
brackets (F) using 2 short screws (B) as shown.
Z Clip Install
Page 3 of 6
Text on page 4
L Clip Install Instructions
Bo
ard
Loc
n atio
Note: Install Masonry Anchors (D) into 1/4” Diameter predrill holes for masonry walls.
Install Drywall Anchors (E) into 1/4” Diameter predrill holes for sheet rock walls.
Top Edge of Board
Bo
Bottom Edge of Board
1 Determine board location. Measure from floor to
the bottom edge of board. Mark with pencil line the corner location. Measure up from bottom edge of board 1-1/4” and draw line as shown. Locate stud near each end of board and drill pilot holes along line using 1/8” drill bit. See diagram below.
Edge of Board
Bo
L ard
oca
16” min. 3” 24” max.
Angle Bracket
Edge of Board
oca
tion
tion
Equally Spaced
Angle Bracket Locations on Board
L ard
3 Set board on the Angle
Lift and remove board from the angle brackets. Measure down from top line of board 1” and draw line as shown. Locate stud near each end of board and drill pilot hole along line using 1/8” drill bit.
Brackets. Draw line along top edge of board.
½ the # of Angle Brackets using
2 Attach
Long Screws (B) as shown.
L Clip Install
5 Secure top Angle Brackets (A) to the wall using 6
long screws (B) as shown. Follow diagram in
- Set board on the bottom angle brackets.
Secure board to bottom and top brackets (A) using short screws (C) as shown.
Page 4 of 6
Text on page 5
Attention
Please read and follow these instructions! Failure to follow these instructions will void your warranty and could result in board failure and possible injury.
- Always use the correct supplied mounting hardware for the type wall your board will be mounted on.
- Use the correct stated predrill for the type anchor you will be using.
- The Angle Brackets and Z Clips MUST be installed according to the layout and spacing as shown below.
NOTE: For more information, please refer to our web-site: www.partsandinstructions.com
WWW.MYBINDING.COM
Page 5 of 6
Text on page 6
Proper L-Clip Layout
Your top and bottom L-Clip layouts should be spaced like this for an 8’ wide board.
If you don’t use this number of L-Clips on top and bottom, your board could end up like this. Please follow these installation directions.
Page 6 of 6 · End of manual
Quick start
- Z-Clip method: Measure from the floor to where the top edge of the board will sit and mark the corner location with a pencil line.
- Measure down 3/4" from the top-edge line and draw a line. Locate a stud near each end of the board and drill pilot holes along the line with a 1/8" bit.
- Attach the Z-Hangers to the wall with the long screws (A).
- Lift, tilt and slide the board down over the Z-Hangers so they catch in the top trim on the back of the board. Draw a line along the bottom edge of the board.
- Lift the board off. Measure up 1-1/8" from the bottom line, draw a line, and drill pilot holes at the studs with a 1/8" bit.
- Secure the 2 bottom brackets (F) to the wall with 2 long screws (A), hang the board back on the Z-Hangers, and fasten it to the bottom brackets with 2 short screws (B).
- L-Clip method: Draw a line 1-1/4" up from the bottom edge location and mount the bottom angle brackets with long screws. Set the board on them, mark its top edge, then mount the top angle brackets on a line 1" below that mark. Fasten the board to the top and bottom brackets with short screws (C).
- On masonry walls, set masonry anchors in 1/4" predrilled holes. On drywall, use drywall anchors in 1/4" predrilled holes.
Frequently asked questions
What wall-mounting options does the Best-Rite 321AB have?
The instructions cover two methods: Z-Clip (Z-Hanger) mounting on page 3 and L-Clip (angle bracket) mounting on page 4.
What anchors do I use on drywall or a masonry wall?
Use the masonry anchors in 1/4" diameter predrilled holes for masonry walls, and the drywall anchors in 1/4" diameter predrilled holes for sheetrock walls. Always use the supplied hardware that matches your wall type (page 3).
What size drill bit do I need for the pilot holes?
Pilot holes into the studs are drilled with a 1/8" drill bit, one near each end of the board along each marked line (page 3).
How far apart should the L-Clip angle brackets be?
The angle brackets are spaced equally along the board, with the diagram showing 16" minimum and 24" maximum between brackets (page 4). The brackets and Z-Clips must follow the layout and spacing shown, or the warranty is void and the board could fail (page 5).
