Page 1 of 6
Text on page 2
Which board assembly instructions should you use?
Use L-Clip instructions for...
Use Z-Clip instructions for...
Scroll down for instructions.
Page 2 of 6
Text on page 3
Z Clip Install Instructions
Top Edge of Board
a Bo
oc rd L
atio
Note: Install Masonry Anchors (D) into 1/4” Diameter predrill holes for masonry walls.
Install Drywall Anchors (E) into 1/4” Diameter predrill holes for sheet rock walls.
Lift, Tilt, and Slide Board down over the Z-Hangers. Z-Hangers should catch in the top trim on the back of the board. Draw line along bottom edge of board.
Bo
oc rd L
atio
Bottom Edge of Board
Determine board location. Measure from floor to the top edge of board. Mark with pencil line the corner location. Measure down from top edge of board 3/4”, and draw line as shown. Locate stud near each end of board and drill pilot hole along line using 1/8” drill bit.
Bo
ard
a Loc
tion
Z Brackets hang in the trim on back of board
Lift and remove board from the Z-Hangers. Measure up from bottom line of board 1-1/8”, and draw line as shown. Locate stud near each end of board and drill pilot hole along line using 1/8” drill bit.
Attach Z-Hangers (E) using Long Screws (A) as shown.
- Secure 2 bottom brackets (F) to the wall using 2
long screws (A) as shown. Hang board on the Z-Hangers (E).
- Secure board to bottom
Screw Anchor - Concrete (For Concrete walls)
Screw Anchor - Drywall (For Drywall)
brackets (F) using 2 short screws (B) as shown.
Z Clip Install
Page 3 of 6
Text on page 4
L Clip Install Instructions
Bo
ard
Loc
n atio
Note: Install Masonry Anchors (D) into 1/4” Diameter predrill holes for masonry walls.
Install Drywall Anchors (E) into 1/4” Diameter predrill holes for sheet rock walls.
Top Edge of Board
Bo
Bottom Edge of Board
1 Determine board location. Measure from floor to
the bottom edge of board. Mark with pencil line the corner location. Measure up from bottom edge of board 1-1/4” and draw line as shown. Locate stud near each end of board and drill pilot holes along line using 1/8” drill bit. See diagram below.
Edge of Board
Bo
L ard
oca
16” min. 3” 24” max.
Angle Bracket
Edge of Board
oca
tion
tion
Equally Spaced
Angle Bracket Locations on Board
L ard
3 Set board on the Angle
Lift and remove board from the angle brackets. Measure down from top line of board 1” and draw line as shown. Locate stud near each end of board and drill pilot hole along line using 1/8” drill bit.
Brackets. Draw line along top edge of board.
½ the # of Angle Brackets using
2 Attach
Long Screws (B) as shown.
L Clip Install
5 Secure top Angle Brackets (A) to the wall using 6
long screws (B) as shown. Follow diagram in
- Set board on the bottom angle brackets.
Secure board to bottom and top brackets (A) using short screws (C) as shown.
Page 4 of 6
Text on page 5
Attention
Please read and follow these instructions! Failure to follow these instructions will void your warranty and could result in board failure and possible injury.
- Always use the correct supplied mounting hardware for the type wall your board will be mounted on.
- Use the correct stated predrill for the type anchor you will be using.
- The Angle Brackets and Z Clips MUST be installed according to the layout and spacing as shown below.
NOTE: For more information, please refer to our web-site: www.partsandinstructions.com
WWW.MYBINDING.COM
Page 5 of 6
Text on page 6
Proper L-Clip Layout
Your top and bottom L-Clip layouts should be spaced like this for an 8’ wide board.
If you don’t use this number of L-Clips on top and bottom, your board could end up like this. Please follow these installation directions.
Page 6 of 6 · End of manual
Quick start
- Choose your hanging method, Z-clip or L-clip, and follow only that section. Always use the supplied hardware for your wall type.
- For drywall, set the drywall anchors in 1/4" pre-drilled holes. For masonry, use the masonry anchors in 1/4" holes. On studs, drill 1/8" pilot holes.
- Z-clip: Measure from the floor to the top edge of the board and mark it. Draw a line 3/4" below that mark, drill 1/8" pilot holes at a stud near each end, and attach the Z-hangers with the long screws.
- Z-clip: Lift, tilt and slide the board down over the Z-hangers so they catch in the top trim on the back. Draw a line along the bottom edge, lift the board off, and drill pilot holes on a line 1-1/8" above it.
- Z-clip: Screw the 2 bottom brackets to the wall with 2 long screws, hang the board on the Z-hangers, then fasten it to the bottom brackets with 2 short screws.
- L-clip: Measure from the floor to the bottom edge of the board. Draw a line 1-1/4" above it, drill 1/8" pilot holes at studs, and attach half of the angle brackets with long screws, spaced as shown in the diagram.
- L-clip: Set the board on the brackets and draw a line along its top edge. Remove the board, draw a line 1" below the top line, drill pilot holes and screw the top angle brackets to the wall with long screws.
- L-clip: Set the board on the bottom brackets and fasten it to the bottom and top brackets with the short screws.
Frequently asked questions
What hardware do I use to mount the 406-70-PM-X2 on drywall or masonry?
Use the drywall anchors in 1/4" diameter pre-drilled holes for sheetrock walls, and the masonry anchors in 1/4" holes for masonry walls. Where you hit a stud, drill a 1/8" pilot hole. See page 3.
Where do I mark the line for the Z-hangers?
Measure from the floor to where you want the top edge of the board, then draw a line 3/4" below it. The bottom bracket line goes 1-1/8" above the line you draw along the board's bottom edge. See page 3.
How many L-clips should I use?
Follow the layout diagram on page 6, which shows the top and bottom L-clip spacing for an 8' wide board. The angle brackets and Z-clips must be installed with the spacing shown. Using fewer L-clips than shown can cause the board to fail.
What happens if I do not follow the mounting instructions?
The sheet warns that not following the instructions voids your warranty and could lead to board failure and possible injury. See page 5.
