Page 1 of 6
Page 2 of 6
Text on page 3
#62382 and #62383 Lumina Reversible Boards
Bottom Cross Brace 1 EA
Should you require assistance during assembly, please call our Customer Service Department Monday - Friday 8 a.m. - 5 p.m. Central Standard Time 1-800-749-2258
Important
The Balt product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal use due to defect or imperfection, the defective part or product will be replaced. Damage caused by common carriers during shipment is not included in this guarantee.
This guarantee sets forth all applicable guarantees and remedies. No other warranty, expressed or implied shall apply. Failure to follow instructions found in Important Information Section of Owner Sheet shall void the guarantee. Consequential or incidental damages and or costs are not refundable.
Page 3 of 6
Text on page 4
Lumina Reversible
Assembly Instructions
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING TO
END BEFORE STARTING TO ASSEMBLE UNIT . 1.) Identify and Separate all the Parts and Hardware.
2.)To attach Hinge Pivot (G) to each side of Board Assembly (P-1), first remove the two factory installed screws in the board’s clamp. Place Hinge Pivot (G) over holes and tighten screws back as shown in Illustration #1A.
3.) Insert the Board Assembly (P-1) between the two Legs (P-2) and connect using two Knobs (F) as shown in Illustration #1B. Leave the Knobs (F) loose.
3.) Attach the Top Cross Bar (P-3), it has two tapped Tray holes on one side of the tube, to the Legs (P-2) using four Screws (A) and tightening with Allen Wrench (D). Repeat this Step to attach the Bottom Cross Bar (P-4) to the Legs (P-2) using four more Screws (A) as shown in Illustration #2.
Page 4 of 6
Text on page 5
#62382 and #62383 Lumina Reversible
4.) Tighten both Knobs (F) at this time. Attach Tray (P-5) to the Top Cross Bar (P-3) using two Screws (A) as shown in Illustration #3. .
K AC
5.) Place a Lock Washer (H) on each Caster’s threaded stem before attaching. . Screw in two Non-Locking Casters (B) and two Locking Casters (C) into the bottom of Legs (P-2) as shown in Illustration #4 and tighten with Caster Wrench (E). .
N RO
WWW.MYBINDING.COM
Page 5 of 6
Page 6 of 6 · End of manual
Quick start
- Read all the instructions first, then identify and separate the parts and hardware.
- On each side of the board, remove the two factory-installed screws in the clamp, place a hinge pivot over the holes and refit the screws.
- Set the board between the two legs and connect it with the two knobs. Leave the knobs loose for now.
- Attach the top cross bar (the one with two tapped tray holes) to the legs with four screws, tightening with the Allen wrench. Attach the bottom cross bar the same way.
- Tighten both knobs, then attach the tray to the top cross bar with two screws.
- Put a lock washer on each caster stem. Screw the two non-locking and two locking casters into the bottom of the legs and tighten with the caster wrench.
Frequently asked questions
What tools do I need to assemble the Lumina Reversible?
The steps use an Allen wrench for the cross bar screws and a caster wrench for the casters, both listed with the hardware. See page 4 and page 5.
Does the stand have locking casters?
Yes. It uses two locking and two non-locking casters, each fitted with a lock washer. See page 5.
What warranty does the Lumina Reversible board have?
The sheet guarantees the product against material and workmanship defects for 1 year from the date of purchase. Defective parts or products are replaced. Shipping damage caused by carriers is not covered. See page 3.
