Page 1 of 3
Text on page 2
2 Locking Casters (E) and 2 Non-Locking
1 Attach
Casters (F) to Legs (P-1) as shown.
Cross Brace (P-3) to Legs (P-1) using 2
- Attach Screws (A).
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING TO
END BEFORE STARTING TO ASSEMBLE UNIT .
Missing Parts or UPS Damaged Parts For Your Convenience you can EMAIL us at
24HOURS 7 DAYS A WEEK
Tighten Casters using Caster Wrench (G).
3 Remove 2 Screws from each side of Framed Board (P4).
Attach 2 Flanges (C) to theFramed Board (P-4) using 4 Screws removed in Step #3.
#668AC, AF & AG
Page 2 of 3
Text on page 3
the frame assembly at the top and insert the Framed Board(P-4) between Legs(P-1) and attach 5 Spread Flanges (C) to the legs using 2 Knobs (D).
6 Assemble Tray (P-2) to Legs (P-1) using 6 Drill Screws (B).
7 Tighten All Screws using a Phillips Screwdriver.
Sh ou l ass d you ass istan requ ir em ce bly dur e ou , ple ing Se r Cus ase rvi ce tom call Mo Dep er a nd ay rtme
- n Ce a.m. Frida t ntr y
- al S p tan .m. dar d T ime T
Cus oll-F
r
1-8 tomer ee
00- Serv 749 ice
Do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorized parts.
WWW.MYBINDING.COM
Page 3 of 3 · End of manual
Quick start
- Read the instructions from beginning to end before you start.
- Attach 2 Locking Casters (E) and 2 Non-Locking Casters (F) to the Legs (P-1) and tighten them with the Caster Wrench (G).
- Attach the Cross Brace (P-3) to the Legs (P-1) using 2 Screws (A).
- Remove 2 screws from each side of the Framed Board (P-4), then use those 4 screws to attach the 2 Flanges (C) to the board.
- Spread the frame assembly at the top, insert the Framed Board (P-4) between the Legs (P-1) and fasten the flanges to the legs with the 2 Knobs (D).
- Assemble the Tray (P-2) to the Legs (P-1) using 6 Drill Screws (B).
- Tighten all screws with a Phillips screwdriver.
Frequently asked questions
What tools do I need to assemble the Best-Rite 668AF-HH?
A Caster Wrench (G) to tighten the casters and a Phillips screwdriver for the final tightening of all screws (page 2, page 3).
How is the board attached to the legs?
Two Flanges (C) are fastened to the sides of the Framed Board (P-4) with the screws you remove from the board. The board is then set between the legs and the flanges are secured to the legs with 2 Knobs (D) (page 3).
Does the stand have locking casters?
Yes. It uses 2 Locking Casters (E) and 2 Non-Locking Casters (F) (page 2).
How often should I check the screws?
Only use it when all screws are tight, and check every screw at least every six months. If parts are missing, broken, damaged or worn, stop using it until your dealer repairs it with factory-authorized parts. (page 3)
