Page 1 of 7
Page 2 of 7
Text on page 3
WOW
Expanding Nest Easel
Hardware List
2” Locking Caster(for front) 2 EA
Should you require assistance during assembly, please call our Customer Service Department Monday - Friday 8 a.m. - 5 p.m. Central Standard Time
Toll-Free Customer Service
Page 3 of 7
Text on page 4
Nest Easel
Assembly Diagram
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING
TO END BEFORE STARTING TO ASSEMBLE UNIT . To Assemble:
- Identify and Separate all the Parts and Hardware.
- Attach Middle Tray (P-3) to 2 Lower Legs (P-1) at desired height using 2 Socket Screws (B) as shown in illustration # 1.
- Attach 2 each Upper Legs (P-2) to the 2 each Lower Legs (P-1) using 4 Socket Screws (A) as shown in illustration # 2.
Missing Parts or UPS Damaged Parts For Your Convenience you can EMAIL us at
24HOURS 7 DAYS A WEEK
Page 4 of 7
Text on page 5
- Insert Markerboard (P-5) into Middle Tray (P-3) as shown in illustration # 3.
- Slide Top Support (P-4) over Markerboard (P-5) and secure to the 2 Upper Legs(P-2) using 2 each Socket Screws(B) as shown in illustration # 4. (Finger tighten only)
Do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorized parts.
Page 5 of 7
Text on page 6
- Attach Book Rack Front Panel (P-7) and Book Rack Back Panel (P-6)to the 2 Lower Leg Frames (P-1) using 4 Socket Screws (A1) and 4 Interior Threaded Posts (C) as shown in illustration # 5.
- Attach 2 Locking Casters (D) in the front and 2 Casters (E) in the back of the unit as shown in illustration # 5. Tighten the Casters using Caster Wrench (G).
(Tighten all Screws at this time)
- Peel the paper from the back of adhesive pad on Plastic Chart Support (F). (See Illustration # 6-A)
Adhesive Pad
See page 7 for High and Low Book Rack Settings
- Attach 2 Plastic Chart Supports on each side of board: Insert 2 pins on back side of Chart Support (F) through holes in markerboard (P-5) as shown in illustration # 6-B.
- Press Plastic Chart Support (F) firmly to the Markerboard surface.
Page 6 of 7
Text on page 7
11.) Attach four of the Plastic Receivers (I) to each Upper Leg (P2) using one Phillips Screw-Short (J) in the top hole and one Phillips Screw-Long(K) in the bottom in the locations shown in illustration #7.
12.) Insert a Hanging Panel (P8) into the Plastic Receivers (I) on each side tube as shown in illustration #8. Place the other two Hanging Panels in the bottom Book Storage.
785-EXP_10-7-13
WWW.MYBINDING.COM
Page 7 of 7 · End of manual
Quick start
- Identify and separate all parts and hardware.
- Attach the Middle Tray (P-3) to the 2 Lower Legs (P-1) at the height you want using 2 Socket Screws (B).
- Attach the 2 Upper Legs (P-2) to the Lower Legs (P-1) using 4 Socket Screws (A).
- Insert the Markerboard (P-5) into the Middle Tray, slide the Top Support (P-4) over it and secure it to the upper legs with Socket Screws (B), finger tight only.
- Attach the Book Rack Front Panel (P-7) and Back Panel (P-6) to the lower leg frames with 4 Socket Screws (A1) and 4 Interior Threaded Posts (C).
- Attach 2 Locking Casters (D) at the front and 2 Casters (E) at the back, tighten them with the Caster Wrench (G), then tighten all screws.
- Peel the backing from each Plastic Chart Support (F), push its pins through the holes in the markerboard and press it firmly to the board (2 on each side).
- Attach four Plastic Receivers (I) to each Upper Leg (P2) with a short Phillips screw (J) at the top and a long one (K) at the bottom, then hang a Hanging Panel (P8) on each side.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Parts are missing or damaged | Shipping damage or missing items | Call the Customer Service Department Monday to Friday, 8 a.m. to 5 p.m. Central Standard Time, or email the 24 hours a day, 7 days a week address. Page 4 |
| Easel wobbles or feels loose | Screws are not tight | Check all screws every six months and tighten them. Do not use the unit unless all screws are tight. Page 5 |
| Parts are broken, damaged or worn | Wear or damage | Stop use until your dealer repairs it using factory authorized parts. Page 5 |
| Casters are loose | Casters not tightened | Attach 2 locking casters in front and 2 casters in back, then tighten them with the caster wrench (G). Page 6 |
| Chart support does not stay on the board | Adhesive pad not applied | Peel the paper from the adhesive pad, insert the 2 pins through the markerboard holes and press firmly. Page 6 |
| Hanging panels do not fit | Plastic receivers not placed correctly | Attach four plastic receivers to each upper leg, then insert a hanging panel into the receivers on each side. Page 7 |
Frequently asked questions
How are the hanging panels attached?
Screw four Plastic Receivers (I) to each upper leg, then insert a Hanging Panel (P8) into the receivers on each side tube. The other two panels go in the bottom book storage (page 7).
Is the height adjustable?
Yes. The Middle Tray (P-3) is attached to the lower legs at the height you choose, and the book rack has high and low settings (page 4, page 6).
Do the casters lock?
The 2 front casters (D) are locking; the 2 back casters (E) are standard (page 6).
How often should I check the screws?
Only use it when all screws are tight, and check every screw at least every six months. If parts are missing, broken, damaged or worn, stop using it until your dealer repairs it with factory-authorized parts. (page 5)
