Page 1 of 8
Text on page 2
EWall Hung Bulletin Board Cabinets
Bulletin Board Cabinet 1 EA (One, Two or Three Door)
Long Screw (1-1/4” )
Short Screw ( 3/8”)
Screw Anchor - Concrete
Screw Anchor - Drywall
Use Screw Anchor (C) in place of Screw Anchor (B) for Drywall Applications.
Important Information
Do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorized parts.
Page 2 of 8
Text on page 3
To Attach to Wall:
- Identify and Separate all the Parts and Hardware.
- Determine the type wall you are going to mount your new Bulletin Board Cabinet (P-1) on. Decide the location and draw a line under the cabinet and on top of the cabinet on the wall as shown in illustration #1.
Draw Line on Wall
- Determine the type mounting brackets that are attached to the back of your Bulletin Board
Cabinet (P-1) . Find the mounting instructions that match your type Cabinet’s mounts on the following pages. .
4a. Bulletin Board Cabinets with four Cross Type mounting brackets:
Measure the distance up from the bottom of the Bullentin Board Cabinet up to the center point of one of the bottom Cross Brackets as shown in Detail #2a. Add thisdistance on top of your bottom Cabinet wall mark and mark a second line that is parallel as shown in illustration #2a. .
Bottom of Cabinet
Bottom of Cabinet Line
Page 3 of 8
Text on page 4
6a. Measure the Length and Width of the center points of the Cross Mounting Brackets as shown in Detail #3a. Use these dimensions to mark your four Mount Screw holes on the wall as shown in illustration #3a. . .
Mount Screw Holes .
Bottom of Cabinet Line
7a. Check Chart A for the correct Screw and Anchor for your type wall.
CHART A
- Use Long Screw (A-1) for attaching direct into wood and metal wall studs.
- Use Screw Anchor (B) and Long Screw (A-1) for attaching into Concrete walls.
- Use Screw Anchor (C) and Long Screw (A-1) for attaching into Drywall.
Page 4 of 8
Text on page 5
8a. Install a Small L Clip (E) on the bottom drawn line in the center. Use the correct hardware for your type wall. Hang the Cabinet by placing the Screw heads into the Cross Type mounting brackets and resting dow on the bottom Small L Clip. Use a Short Screw (A2) through the bottom Small L Clip’s leg to secure the cabinet in place. See illustrations # 4a and 5a.
Top edge of cabinet
Bottom edge of cabinet
4b. Bulletin Board Cabinets with Cross Type Mounting Brackets at the top and L Clips at the bottom:
Measure the distance from the top of the Bulletin Board Cabinet down to the top center point of the Cross Brackets as shown in Detail #2b. Draw a lower line parallel to the top Cabinet line. Measure the distance between the Top Cross Type brackets and mark this distance on the second top line you just drew. Install the correct mounting hardware for your type wall in these marks. See illustration #2b. . Top of Cabinet
Bottom of Cabinet
Page 5 of 8
Text on page 6
6b. Install the Large L Clips (D) on the bottom drawn line of Cabinet as shown in illustration #3b.
7b. Place the Cabinet’s Cross Type Top Mounting brackets over the heads of the top hanging Screws and lower Cabinet doewn onto the bottom Large L Clips (D). Secure in place using Short Screws (A2) into the bottom leg of the L Clip and into the Cabinet’s bottom frame as shown in illustration #4b.
Page 6 of 8
Text on page 7
Bulletin Board Cabinets with Z Hanger Bar at top and L Clip at bottom:
5c. Measure the distance down fro the top edge of your Cabinet to the center point of the Z Hanger Bar that is screwed to the back. Measure down this same amount from the top line you drew on the wall and draw a line parallel to it. This will be the top edge location of the wall mounted Z Hanger (F). Mount the Z Hanger (F) to the wall using the correct hardware for your type wall (see Chart A on page 4). See Detail # 2c and illustration # 2c.
Top of Cabinet
Bottom of Cabinet
6c. Place a Small L Clip (E) in the center of the bottom drawn line of the Cabinet. Attach it to the wall with the correct Hardware as shown in illustration #3c. .
7c. Hook the Cabinet’s Z-Hanger on the Z-Hanger on the wall. Secure the Cabinet to the wall and the Small L Clip using Screw (A2) as shown in illustration #4c.
Page 7 of 8
Text on page 8
4d. Bulletin Board Cabinets with Large L-Clips Top and Bottom:
5d. Install the Large L-Clips on the bottom drawn line with the correct Hardware for your type wall. Make sure the bottom edge of the L-Clips are even with the bottom line when the Screw (A1) is in the top of the L-Clips slot as shown in illustration #2d.
6d. Install the top Large L-Clips so that they can be raised 1/2” above the top drawn line and then pushed down to touch the line and the top of the board once it is installed. See illustration # 2d.
7d. Place the Cabinet on the bottom row of L-Clipsand tilt the Cabinet up against the wall. Push the top L-clips down until they touch the top of the Cabinet. Secure the L-Clips to the Cabinet using Small Screws (A2). .
Bulletin Board Cabinets 1-30-14
Page 8 of 8 ยท End of manual
Quick start
- Identify and separate all parts and hardware.
- Decide where the cabinet goes and draw a line on the wall at the bottom and at the top of the cabinet.
- Check which mounting brackets are on the back of your cabinet and follow the matching procedure (cross brackets, cross brackets with bottom L-clips, Z-hanger bar, or large L-clips).
- Choose hardware from Chart A: Long Screws (A-1) into wood or metal studs, Screw Anchor (B) with Long Screw for concrete, Screw Anchor (C) with Long Screw for drywall.
- Measure from the cabinet edge to its brackets or hanger, transfer the measurements to the wall and install the screws, Z-hanger or clips.
- Hang the cabinet and secure it to the bottom clip with Short Screws (A2).
Frequently asked questions
Which mounting instructions apply to my cabinet?
It depends on the brackets attached to the back of the cabinet. The guide covers four types: four cross-type brackets, cross brackets at the top with L-clips at the bottom, a Z-hanger bar at the top with an L-clip at the bottom, and large L-clips top and bottom (page 3 to page 8).
What screws and anchors should I use for my wall?
Use Long Screws (A-1) directly into wood or metal studs, Screw Anchor (B) with a Long Screw for concrete, and Screw Anchor (C) with a Long Screw for drywall (page 4).
Can I mount it on drywall?
Yes. Use Screw Anchor (C) in place of Screw Anchor (B) for drywall (page 2).
How often should I check the mounting screws?
Only use it when all screws are tight, and check every screw at least every six months. If parts are missing, broken, damaged or worn, stop using it until your dealer repairs it with factory-authorized parts. (page 2)
