Page 1 of 6
Text on page 2
WOW
DOC Room Divider
Hardware List
Parts List
Screw M5 X 8mm
Screw M5 X 50mm
Screw M6 X 55mm
For Hooking Two Units Together
Page 2 of 6
Text on page 3
DOC
Assembly Diagram
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING
TO END BEFORE STARTING TO ASSEMBLE UNIT .
To Assemble: 1.) Identify and Seperate all the Parts and Hardware
2.) Place two Screw Blocks (E) into the slot of the aluminum side extrusion on each side of the Board (P1) as shown in Illustration #1 Detail A-1. Attach four Plastic Mounting Brackets (D) to the Screw Blocks (E) using one Screw (A) in the center of each bracket. Assembly should slide easily.
NOTE: Tilt the Screw Blocks (E) at a 45 degree angle as you insert them into the side extrusion’s slot. They should fall into place.
Page 3 of 6
Text on page 4
3.) Align the upright Post (P3) with the holes in the Plastic Mount Brackets (D) on each side and attach with two Screws (A1). These Screws (A1) go through the plastic Mounting Brackets (D) and tighten into the Screw Blocks (E) as shown in Illustration #2.
4.) Insert two Bumpers (B) in the top holes on Crossbrace (P2) as shown in Illustration #3.
Page 4 of 6
Text on page 5
5.) Slide the Crossbrace (P2), with Bumpers (B) facing up, in between the Posts (P3) and up to the bottom of Board (P1). Line up the the Crossbrace’s (P2) mount holes with the holes in the Posts (P3) and secure using two Screws (A2) on each side as shown in Illustration #4.
6.) Place a Leg Base (P4) on the end of each Post (P3) and lign up the slot hole in the Leg Base (P4) with the threaded hole in the Post (P3). Note: The Leg Base (P4) may be turned to the inside or to the outside. Use Leg Secure Screw (L) to attach Leg Base (P4). Do not tighten at this time. Insert a Bottom Leg Bolt (J) through a Large Bottom Washer (K) and into the bottom of each Leg Base (P4) and tighten with Large Allen Wrench (G). You can now tighten each Leg Secure Screws (L) as shown in Illustration #5.
Leg Base shown turned to inside
Page 5 of 6
Text on page 6
7.) Push in four Locking Casters (C) into the legs of the Leg Bases (P4) and stand completed unit upright.
DOC_10-9-14
Page 6 of 6 · End of manual
Quick start
- Identify and separate all parts and hardware.
- Tilt two Screw Blocks (E) at 45° into the slot on each side of the board, then attach four Plastic Mounting Brackets (D) with one Screw (A) each.
- Attach an upright Post (P3) on each side with two Screws (A1) through the brackets into the screw blocks.
- Insert two Bumpers (B) in the top holes of the Crossbrace (P2), slide it between the posts up to the board and secure with two Screws (A2) per side.
- Fit a Leg Base (P4) on each post with the Leg Secure Screw (L) loose, fit the Bottom Leg Bolt (J) and washer (K) with the large Allen wrench, then tighten the Leg Secure Screws.
- Push the four Locking Casters (C) into the leg bases and stand the unit upright.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Parts are mixed up during assembly | The parts and hardware were not sorted first. | Read the instructions from beginning to end before starting. Identify and separate all the parts and hardware. Page 3 |
| Screw blocks will not go into the side extrusion | The blocks are not angled when inserted. | Tilt the screw blocks (E) at a 45 degree angle as you insert them into the slot. They should fall into place. Assembly should slide easily. Page 3 |
| Post does not line up with the mounting brackets | The post holes are not aligned with the bracket holes. | Align post P3 with the holes in the plastic mount brackets D on each side and attach with two screws A1 into the screw blocks E. Page 4 |
| Crossbrace is the wrong way up | The bumpers are not facing up. | Insert two bumpers B in the top holes of crossbrace P2. Slide it in with the bumpers facing up, then secure with two screws A2 on each side. Page 5 |
| Leg base will not fit right | The leg secure screw was tightened too soon. | Attach leg base P4 with leg secure screw L but do not tighten yet. Insert bottom leg bolt J through large washer K and tighten with the large Allen wrench G. Then tighten screws L. Page 5 |
| Unit will not stand or roll | The casters are not fitted. | Push the four locking casters C into the legs of the leg bases, then stand the unit upright. Page 6 |
Frequently asked questions
Can the leg bases face inward?
Yes. The Leg Base may be turned to the inside or the outside. See page 5.
Can two dividers be connected?
The hardware list includes M6 x 55mm screws for hooking two units together. See page 2.
Does the divider roll?
Yes. Four locking casters push into the leg bases. See page 6.
