Page 1 of 7
Text on page 2
Great Divide Add-On Panel
Spring Assisted Foot Assembly
Hardware List
Screw M6X12mm See note on page 3
Important
The BestRite product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal use due to defect or imperfection, the defective part or product will be replaced. Damage caused by common carriers during shipment is not included in this guarantee. Do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorized parts. This guarantee sets forth all applicable guarantees and remedies. No other warranty, expressed or implied shall apply. Failure to follow instructions found in Important Information Section of Owner Sheet shall void the guarantee. Consequential or incidental damages and or costs are not refundable.
Page 2 of 7
Text on page 3
Insert 4 STARTING StorageTubs TO (P6). R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING TO END BEFORE ASSEMBLE UNIT .
NOTE: Some screws (A) are installed by the factory for shipping purposes and must be removed and reinstalled during the assembly process. Mounting Illustration # 1A Bracket To Assemble:
1.) Identify and Separate all the Parts and Hardware.
2.) Pull up on mounting brackets of the 2
Foot assemblies (P-4), rotate brackets 90 degrees until they lock in position as shown in illustration # 1A & 1B.
Pull up on mounting Bracket and Turn 90 Degrees.
Foot assembly (P-4) after rotating bracket
Missing Parts or UPS Damaged Parts For Your Convenience you can EMAIL us at
3.) Press 2 Locking Casters (B) onto the
bottom of the Foot Assembly (P-4) as shown in illustration # 2.
24HOURS 7 DAYS A WEEK
Page 3 of 7
Text on page 4
GREAT DIVIDE STARTER UNIT + 1 GREAT DIVIDE ADD-ON UNIT
For 3 Middle Panels (P-2) Follow these assembly instructions when 1 Add-On Panel unit will be connected to an existing Great Divide Starter Panel unit.
P-2 from ADD-ON
P-2 from STARTER
4.) Attach two (P-6) Hinges to the bottom and two (P-6) Hinges to the top of the Middle Panels (P-2) using 16 screws (A) as shown in Illustration #3.
NOTE: At this point, go back to the Great Divide Starter Unit instructions and substitute this assembly for the single P-2 Middle Panel in Step 5.
GREAT DIVIDE STARTER UNIT + 2 GREAT DIVIDE ADD-ON UNITS
For 5 Middle Panels (P-2) Follow these assembly instructions when 2 Add-On Panel units will be connected to an existing Great Divide Starter Panel unit.
5.) Attach four (P-6) Hinges to the bottom and four (P-6) Hinges to the top of the Middle Panels (P-2) using 32 screws (A) as shown in Illustration #4.
P-2 from STARTER
P-2 from ADD-ONs
NOTE: At this point, go back to the Great Divide Starter Unit instructions and substitute this assembly for the single P-2 Middle Panel in Step 5.
Page 4 of 7
Text on page 5
GREAT DIVIDE STARTER UNIT + 3 GREAT DIVIDE ADD-ON UNITS
For 7 Middle Panels (P-2)
Follow these assembly instructions when 3 Add-On Panel units will be connected to an existing Great Divide Starter Panel unit.
P-2 from STARTER
P-2 from ADD-ONs
6.) Attach six (P-6) Hinges to the bottom and six (P-6) Hinges to the top of the Middle Panels (P-2) using 48 screws (A) as shown in Illustration #5. NOTE: At this point, go back to the Great Divide Starter Unit instructions and substitute this assembly for the single P-2 Middle Panel in Step 5.
P-1 & P-3 Assembly
P-2 from ADD-ONs
7.) Attach each End Panel (P-1) and Middle Panel w/ Tube (P-3) assembly to your number of Middle Panels (P-2) using 8 screws (A) and going through Hinge (P-6) at the bottom and the top as shown in Illustration #6.
Page 5 of 7
Page 6 of 7
Text on page 7
PANEL LOCK LOCATION CHART
(BOTTOM VIEW)
Panel Lock location for GREAT DIVIDE STARTER UNIT
9.) Attach a Panel Lock(P-7) to the bottom of each End Panel(P-1) using one Screw, one Lock Washer and one Flat Washer, that come in the Panel Lock P-1 package, in the hole locations shown in Illustration #8.
Panel Lock location for GREAT DIVIDE STARTER UNIT + 1 ADD-ON UNIT
Panel Lock location for GREAT DIVIDE STARTER UNIT + 2 ADD-ON UNITS
Panel Lock location for GREAT DIVIDE STARTER UNIT + 3 ADD-ON UNITS
Page 7 of 7 · End of manual
Quick start
- Read the instructions through before you start, then identify and separate all parts and hardware. Some M6x12mm screws (A) are factory-installed for shipping and must be removed and reused.
- Pull up on the mounting brackets of the two foot assemblies (P-4) and rotate them 90 degrees until they lock.
- Press two locking casters (B) onto the bottom of each foot assembly.
- For 1 add-on (3 middle panels): attach two hinges (P-6) to the bottom and two to the top of the middle panels (P-2) with 16 screws. For 2 add-ons use 4+4 hinges and 32 screws; for 3 add-ons use 6+6 hinges and 48 screws.
- Return to the Starter Unit instructions and use this hinged assembly in place of the single middle panel in Step 5.
- Attach the end panel (P-1) and the middle panel with tube (P-3) to the middle panels with 8 screws through the top and bottom hinges.
- Fit a panel lock (P-7) to the bottom of each end panel with the screw, lock washer and flat washer supplied, using the hole locations in the panel lock chart.
Frequently asked questions
How many hinges and screws do I need for each add-on unit?
One add-on uses 4 hinges and 16 screws, two add-ons use 8 hinges and 32 screws, and three add-ons use 12 hinges and 48 screws. See page 4 and page 5.
Can I add more than one add-on panel to a Great Divide Starter unit?
Yes. The sheet covers a starter unit with 1, 2 or 3 add-on units (3, 5 or 7 middle panels).
What warranty covers the Great Divide panels?
Best-Rite guarantees the product against material and workmanship defects for 1 year from the date of purchase. Shipping damage by carriers is not covered (page 2).
How often should I check the screws?
At least every six months. Do not use the divider unless all screws are tight (page 2).
