Text on page 1
BEST-RITE ____
“It’s A Better Board”
Page 1 of 5
Text on page 2
WOW
Straight Wall Swing Panels (698)
Top Cross Bar w/ deep holes 1 EA
Bottom Cross Bar w/ angle support 1 EA
Tool required: Adjustable Cresent Wrench or Socket Wrench
Should you require assistance during assembly, please call our Customer Service Department Monday - Friday 8 a.m. - 5 p.m. Central Standard Time
Toll-Free Customer Service
Page 2 of 5
Text on page 3
Wall Mount Swing Panels
Assembly Diagram
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING
TO END BEFORE STARTING TO ASSEMBLE UNIT .
- To Assemble:
Identify and Separate all the Parts and Hardware.
2. Assemble Top Cross Bar with deep holes (P-2) on top of Uprights (P-1) with holes facing down. Bottom Cross Bar with angle support (P-3) should go on the bottom of the Uprights (P-1) with holes facing up. Use Socket Screws
(A) and Interior Threaded Post (B), and tighten with Allen Wrench (H). See illustration #1.
3. Find the desire location and mark the 16 screw holes with pencil on the wall by using the assembled main frame as a pattern. Drill the holes and make sure you drilled holes in stud or solid part of the wall. Please make sure you use proper anchor bolts if ours are not suitable for your type of wall. See illustration #2
Anchor Bolt Assembly
Anchor Bolt (assembled)
5. Insert the assembled Anchor bolts inside the holes untill Washers are flush with the surface of the wall. Tighten the nuts with Socket Wrench to spread the Anchor Sleeve (F) from the slot in the wall. See Illustration #4 and #4a.
4. Assemble Anchor Bolts, if you chose to use and are suitable for your wall, by inserting Anchor Bolt (G) into the Anchor Sleeve (F) from the slotted end. Insert the Flat Washer (D) over the Bolt and fasten the Nut (C). Tighten by hand as shown in illustration #3.
Missing Parts or UPS Damaged Parts For your convenience you can EMAIL us at
24 HOURS 7 DAYS A WEEK
Page 3 of 5
Text on page 4
- Remove Nuts (C) and Flat Washers (D) off of the Anchor Bolts (G) from the wall. Place the assembled Wall Mount Frame over the Anchor Bolts (G) coming out of the wall as shown in illustration #5 and #5a
- Place the Flat Washer (D) and Lock Washer (E) over the Anchor Bolt (G) and fasten the Nuts (C). Tighten all 16 nuts by using Socket Wrench or Adjustable Wrench. See illustration #6 and #6a.
Do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorized parts.
Page 4 of 5
Text on page 5
- Remove the poly cover from both sides of the Acrylic Panels (P-6). Slide the White Poster Panle (P-5) or Hook & Loop board (optional) in between the Acrylic Panels (P-6), and insert into the Panel Frame (P-4). See illustration #7. If you have 698U model you would not have the Acrylic Panels (P-6).
- Insert one tab of Panel Spacer (I) in punched slot, and using your thumb, compress the Panel Spacer (I) until the second tab inserts into the second slot. See illustration #8 and #8a. There are 2-Spacers (I) per each Panel Frame (P-4).
- Place the long stub coming out of the Panel Frame into first hole underneath the Top Cross bar (P-2). Push up as far as it goes into the hole and set the smaller Stub on the bottom of the Panel frame (P-4). Line up with the first hole on Bottom Cross bar (P-3) as shown in illustration #9. Repeat the same step to place all your Panel Frames (P-4).
- Slide the U-Channel (P-7) on top of each Panel Frame (P-4). This step will secure all panels from falling off. See illustration #10 and #10a. To access the panels you must remove the U-Channel (P-7).
Page 5 of 5 · End of manual
Quick start
- Identify and separate all parts. You need an adjustable crescent wrench or socket wrench.
- Fit the top cross bar (holes down) and bottom cross bar (holes up) to the uprights with socket screws and threaded posts, tightened with the Allen wrench.
- Use the frame as a template to mark the 16 screw holes, and drill into studs or solid wall.
- Assemble the anchor bolts, insert them flush with the wall and tighten to spread the sleeves.
- Remove the nuts and washers, place the frame over the bolts, refit flat and lock washers and tighten all 16 nuts.
- Remove the poly cover, slide the poster panel between the acrylic sheets and insert into a panel frame with 2 spacers. Model 698U has no acrylic panels.
- Hang each panel frame in the top and bottom cross bar holes and slide a U-channel onto each one.
Frequently asked questions
What tools do I need for the 698 swing panels?
An adjustable crescent wrench or socket wrench, plus the Allen wrench used for the cross bars (page 2).
How many anchor bolts hold the frame to the wall?
Sixteen (page 4).
What is different about the 698U model?
The 698U does not include the acrylic panels (page 5).
