Copyright © 2013 by Stephanie Hwang

All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of the publisher, except in the case of brief quotations embodied in critical reviews and certain other noncommercial uses permitted by copyright law. For permission requests, write to the publi

Sealer Sales, Inc. 8820 Baird Avenue Northridge, Ca 91324 www.sealersales.com

Printed in the United States of America

General Information

Thank you for purchasing our CBS-880 continuous band sealer.

your band sealer machine. The manual will provide you with basic information concerning both operation and maintenance of your new machine. Please read it carefully as failure to do so may result in bodily injury and/or damage to the equipment.

Please fill in the information below. You will find the information on the machine identification plate. You will need this information when ordering replacement parts or making technical inquiries.

No part of this manual may be duplicated, reproduced, stored in a retrieval system, translated, transcribed, or transmitted in any form without the express prior written permission of Sealer Sales.

EQUIPMENT

INFORMATION

Purchase Date:

Reference # (found on packing slip)

Owner:

Table of Contents

Safety Instructions ........................................................................................... 1 Introduction ...................................................................................................... 3 Operating your Band Sealer ............................................................................ 7 Vertical Configuration Set-up ....................................................................... 13 Maintenance .................................................................................................... 18 Parts Diagram ................................................................................................. 20 Troubleshooting ............................................................................................. 34 Spare Parts List ............................................................................................... 36 Quality Control Testing ................................................................................. 37

Safety Instructions

Below are general safety precautions and warnings that should be understood prior to setting up or operating your equipment. Read and fully understand all instructions and warnings prior to using this unit. Your safety is most important! Failure to comply with procedures may result in serious injury or property damage. Remember:

Unsafe practices or unauthorized modifications could result in accidents or property damage. Failure to follow these safety rules and take necessary precautions can result in serious injury as well as damage to equipment.

Never operate or service your band sealer until you have read this manual completely and understand it fully.

Plug the band sealer into a standard 120 Volt, 60Hz wall outlet or surge protector. We highly suggest using a surge protector. Some special order units are 220 Volt, 50Hz. Make adjustments as necessary.

Do not use the band sealer if the power cord, plug or any other parts are damaged. Be sure not to allow the power cord to drape into your work area. Check that all parts are operating properly and perform the intended functions. Check for all other conditions that may affect the operation.

Reduce risk of unintentional starting. Make sure the power switch is in the "OFF" position before attaching to the power source.

Always disconnect sealer from power source before servicing, changing accessories or cleaning the unit.

To provide protection against the risk of electrical shock, the power connection must be properly grounded at all times.

Do not leave the sealer unattended when in use. Disconnect the sealer from the power source before leaving the work area.

Band sealer is used solely for sealing thermoplastic materials. Using the machine for any other purpose can cause damage to the machine and operator. Do NOT use the machine for any other purpose other than to seal thermoplastic materials. Doing so may result in damage to the machine and injury to the operator.

Always operate machine on a flat stable surface.

While operating machinery, wear close-fitting clothing and tie back long hair to prevent any external items from getting caught in the machine. Do not wear jewelry when operating the band sealer.

While machine is operating do not touch the heating and/or cooling blocks. Blocks will be extremely hot and may burn your hands.

While machine is in operation, do not place fingers, tools, or other foreign objects on or into the machine. Do not touch any moving parts while machine is operating. Fingers may get caught in between the gears /pinch points and cause significant injury.

Thermoplastic bags and material are hand fed into the machine. Place bag on the guide and carefully feed the bag through the band sealer. Fingers may be placed on the guide but do not allow fingers to touch any of the moving parts on the band sealer.

Use emergency stop to turn off machine should material/bags get jammed into the machine. Carefully pull material out of the band sealer. Do NOT use fingers to touch any part of the machine.

The band sealer is not water resistant or water proof. Spraying down the machine will damage machine or cause electrical shock. Do not submerge the band sealer into water or liquid.

Do not operate band sealer in a corrosive or humid environment.

Always keep the machine clean, lubricated and in good working condition. Follow any maintenance and lubrication procedures outlined in this manual. Make sure unit is disconnected from power source before cleaning

NEVER use any accessories or parts from other manufacturers. Machine should not be altered or modified using parts that are not genuine authorized parts. Doing so will VOID YOUR WARRANTY.

Never leave the band sealer unattended. Be safe, disconnect the band sealer from power source before leaving work area.

Close supervision is necessary when any appliance is near children or persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge . This sealer is NOT to be used by children or by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge.

DO NOT use the band sealer outdoors.

DO NOT use the band sealer while under the influence of drugs, medications or alcohol.

SAVE THESE INSTRUCTIONS - REFER TO THEM OFTEN AND USE THEM TO INSTRUCT OTHERS.

Introduction

CBS-880 is equipped with an electronic temperature controller and variable speed conveyor to seal all types of thermoplastic materials (PP, PE, stand up pouches, gusseted bags, moisture barrier bags, etc.). Seals are created using PTFE bands which maintain high seal quality and produce consistently strong, clean seals on all heat sealable bags. Because bags are placed on a conveyor system, the width of the bag does not matter. These versatile machines offer several adjustments which allow them to be used for a wide range of applications. These machines are used extensively in the food/produce, medical, chemical, cosmetic, and electronic industries. The CBS-880 band sealer will significantly increase efficiency of packaging your products.

There are two configurations for the CBS-880 band sealer. The horizontal configuration (CBS-880I) is primarily used for sealing dry materials and when you can lay flat your pouch. The vertical configuration (CBS-880II) typically seals small solid products (ex: powders, grains, coffee) and liquids. In addition, sealing using the vertical configuration also works best with stand up pouches.

Features of the CBS-880 Band Sealer

Your band sealer is equipped with a wide range of standard features and capabilities.

Simple to use minimal operator training Rust inhibiting stainless steel construction Unit feeds right to left Equipped with electronic adjustable speed control Equipped with bag entry guide for easy bag feeding and straight seals Control panel includes industrial grade safety emergency stop switch 10amp protection power surge breaker Wide seal (8mm) to assure airtight seal / Optional 15mm width sealer model available PTFE sealing belts Extended forced-air cooling system with extra wide cooling bars and 6 heat transfer orifices One pair of brass sealing bars Sealing method constant heat Adjustable 2-way pulley system for optimal stability and embossing clarity Knurled pressure rolls with variable pressure adjustment Fast warm up time PID digital temperature controller 0temp) Motorized rubber conveyor with speed control Capable of speeds up to 472 inches/minute Optional pressure embossing printing coder

How Does the CBS-880 Work?

CBS-880 is comprised of a stainless steel frame, speed adjusting mechanism, sealing temperature control system and transmission system. Turning on the heat for the band sealer will cause a rapid rise in the temperature of the heating blocks. Required temperature and speed can be adjusted via the temperature controller and speed adjusting device. Plastic material to be sealed is placed on the guide and conveyor. Conveyor will then take the material between the two heating blocks to fuse the material together. Material will then pass through the cooling blocks to allow the material to congeal. Finally, material will then pass through the embossing wheel for a meshed seal line.

CBS-880 is easy to use. To seal, adjust temperature and place bag on conveyor

The motor drives the sealing belts, drive belts and conveyor simultaneously.

Specifications

Power Motor Power Sealing Speed Sealing Width Temperature Range Conveyor Size Max Conveyor Load Min/Max Height of Bag (Vertical Only) Character Size Embossing (Optional Feature)

110V/60Hz 50W 0-472 inches/minutes 8mm (Optional 15mm width available)

3x4x9mm / 18PT 1 line embossing (2 lines available) 3 sections w/ 15 characters/line

Dimensions Weight

CBS-880 Diagram

Figure 1. Horizontal Band Sealer (1) Guide, (2) Driven Wheel Seat (Adjusting Block), (3) Driven Wheel, (4) Control Panel, (5) Heating Block, (6) Holding Plate, (7) Pinch Roller, (8) Cooling Block, (9) Driving Wheel, (10) Embossing Roller, (11) Silicone Wheel, (12) Guiding Wheel, (13) Conveyor Belt, (14) Conveyor Table, (15) Fastening Knob for Elevating Table, (16) Transverse Tightening Knob for Conveyor Table, (17) Conveyor Support

Figure 2. Vertical Band Sealer (1) Conveyor Table, (2) Driving Roller, (3) Conveyor Belt, (4) Fixed Bracket, (5) Slip Bracket, (6) Safety Cover, (7) Adjusting Knob for Embossing Roller, (8) Housing, (9) Circuit Breaker, (10) Control Panel, (11) Feed Opening, (12) Fastening Knob, (13) Worktable, (14) Adjusting Knob for Conveyor Belt, (15) Tightening Nut, (16) Transverse Tightening Knob for Conveyor Table, (17) Conveyor Support, (18) Vertical Shaft, (19) Gimbel Assembly, (20) Umbrella Gear Shaft

Figure 3. Horizontal Band Sealer with Stand. Optional stand available for CBS-880. Please ask your distributor.

Cbs-88Oinstructionmanual

Getting to Know your Band Sealer

Sealing Height Knob Adjust:seaingheight cn

Umbrella Gear Base

Embossing Knob

Circuit Breaker

Bag entry guide

Conveyor Height Adjustment

Heat Switch

ollerto adivate seaing

Xmte1000

Temperature

Continuous Band Sealer

ed Adjustiment

Electrical Circuit Diagram

Figure 4. Electrical Circuit Diagram. (QF1) Breaker, (SB1) Switch/Emergency Stop, (K1) Switch/On-Off, (K2) Switch/Seal, (K3) Switch/Fan, (MD) DC Motor, (FAN) Axial-Flow Fan, (THC1) Temperature Controller, (ST1) Thermocouple, (HE1) Heating Element, (W1) Potentiometer, (AP1) Speed-Regulating PCB

Operating Your Band Sealer

Initial Set-up

To prevent damage to the band sealer, the band sealer body and conveyor are shipped disconnected. Please follow these simple steps to connect the drive shaft (Figure 34, Item #17) on the band sealer body with the conveyor middle post (Figure 40, Items #5, 14-18) on the band sealer conveyor.

1. Loosen the knobs for the conveyor table to move the conveyor table forward.

Figure 5. Two flower shaped knobs are found under conveyor.

2. Loosen the screw on the drive shaft and insert the conveyor middle post (found on the conveyor table) to the drive shaft. Be sure the groove on the conveyor middle post lines up along the screw on the drive shaft. Move the conveyor belt as needed to allow the conveyor middle post to meet with the drive shaft. Once the conveyor middle post is in place, tighten the screw on the drive shaft to lock the conveyor middle post in place.

Figure 6. Insert the conveyor middle post in drive shaft. Make sure grooves are aligned.

Figure 7. Tighten the screw on the drive shaft to lock the conveyor middle post in place.

3. Tighten the round nut (Figure 34, Item #18) along the drive shaft as well as the knobs and in front of the band sealer (Figure 40, Item #12)

Operation Set-up

1. Our machines are equipped with a three-prong grounded plug. Make sure the plug is wellconnected in the socket to ensure safe operation.
2. Make sure the circuit bre

tion. (Levers pointing up)

3. First time operation. Allow the machine to pre-heat by running at a low temperature for a few minutes. This would apply if the machine has not been in operation for a long time. The machine can sometimes be damp from storage or shipment and running at a low temperature will dry out any residual moisture.
4. Adjust the conveyor position forwards or backwards. Refer to Figure 8 for knob adjustments. For vertical configuration only, adjust the height of the band sealer appropriate for your bag to be sealed.

Figure 8. (1) Adjusting Knob, (2) Foot Rest

5. Adjust the guide to adjust seal width and position of seal line on your material.

Operation

Figure 9. Control Panel of CBS-880

1. Switch the circuit breaker (Figure 44 , Item #7) to the "On" position.
2. Turn Power, Heater, and Fan switches to the On position. Belts and conveyor will begin to move simultaneously.

Press the emergency stop to turn off the machine. In order to restart the

4. Adjust the conveyor speed.
5. Adjust the temperature controller to the temperature desired to seal your material. Temperature settings will vary based on bag material and thickness. If you are unsure what temperature setting to use, we recommend starting at a low temperature and gradually increase to a temperature that will seal your material. The PV value (red light) is the actual temperature and the SV value (green light) is the desired temperature setting.

Figure 10. CBS-880 Temperature Controller

1. To set the temperature, press the SET button.
2. Press the <AT (auto tuning) button to move from the ones, tens, and hundreds place. Adjust the value using the up and down arrows.
3. Press the SET button to save the temperature settings. Your desired temperature settings should appear in green in the SV Value.

d. Wait until the PV temperature matches the SV temperature which should take approximately 5-10 minutes.

6. Adjust the pressure knob (Figure 34 , Item #7) on your band sealer depending on the thickness of your bag material.

7. Place material on the guide (Figure 34 , Item #1) and allow the band sealer to pull your material through. Make sure your material is flat on the guide. While the material is moving through the band sealer, do not push or pull the material as this will cause irregular sealing.

8. If the sealing belt is running off the guide wheels, make adjustments to the screws that are found on the driven wheel seat (Figure 11, Item #1 & 2)

Figure 11. (1) Driven Wheel Seat (Adjusting Block), (2) Driven Wheel Seat (Adjusting Block), (3)/(4) Adjusting Screws, (5) Springs

9. To shut down, turn off the heater switch and allow the temperature of the machine to drop before turning off the power and fan switches. Following the shut down procedure will significantly prolong the life of machine and sealing belts.

Installing the Embossing Wheel (Optional Feature)

CBS-880 can be equipped with an optional embossing function. The embossing coder will continually emboss characters directly on your bag. The coder uses pressure and does not use ink to print. The CBS- 880 embossing wheel is equipped for 1-line embossing with 15 characters. There are three sections so three sets of characters are needed. Optional feature: 2-line embossing which can be purchased separately.

1. Place the key in the groove of the embossing wheel plate and turn counter clockwise to loosen the print wheel plate. (Figure 12) Remove the embossing wheel plate, as well as the o-ring (Figure 13)
2. Carefully install your typesets in each of the three cavities. Once all cavities are filled, place the o-ring and print wheel plate back in place. Using the key, carefully turn clockwise to lock wheel plate. Make sure none of the typesets are pushed out of the cavity by holding the typesets in place as you turn the key.
3. Unscrew and remove the pattern knurled wheel on the sealer. Replace with the embossing wheel by lifting the embossing wheel seat and pushing the embossing wheel in place. Please note: remove safety cover before accessing the embossing wheel.

Sealing & Printing Optimization

1. Sealing performance can be adjusted with the sealing temperature and sealing speed. The higher the speed the less exposure the material and therefore a higher temperature will be required to seal the material.
2. Try a variety of different sealing temperatures and conveyor speeds to get the optimal seal for your material.
3. Make adjustments to the pressing wheel with the pressure knob (Figure 34 , Item #7) to ensure a good quality seal as well as a clear and visible embossed image.

Vertical Configuration Set-Up

To use the CBS-880 in its vertical configuration, please follow the instructions below. If you purchased the CBS-880I horizontal band sealer and wish to use your band sealer in the vertical configuration, please order the conversion kit (Part # CBS-880-72) from your distributor.

Figure 16. CBS-880II Vertical CBS-880 Band Sealer for sealing liquids and stand up pouches

1. Detach the conveyor table by removing the two knobs under the conveyor table. Slide the conveyor table off the conveyor support.
2. Remove the drive shaft (Figure 34 , Item #17) and loosen the round nut (Figure 34 , Item #18).

Figure 17. Remove the two knobs underneath the conveyor to slide the conveyor off the conveyor support.

Figure 18. After removing the conveyor, remove the drive shaft and loosen the round nut.

3. Assemble the vertical stand as in the diagram below.

Figure 19. Parts needed to convert to the vertical configuration.

Figure 20. Assemble vertical stand as shown above.

4. Remove the cover from the Umbrella Gear (Figure 45, Item #4). Set aside for later.

Figure 21. Remove the cover from the umbrella gear by removing the four screws on the side of the gear.

Figure 22. Umbrella Gear without the cover.

5. Turn the umbrella gear over and remove the three screws/nuts. Keep screws aside for later.

Figure 23. Remove the three screws and nuts on the umbrella gear.

Figure 24. Umbrella Gear without the screws.

6. Insert the long drive shaft of the Umbrella Gear into the axis hole. Take note of the alignment groove.

Figure 26. Take note of the alignment grove in the axis hole.

Figure 25. Insert umbrella gear into the axis hole.

7. Insert the vertical stand from step 3 into the conveyor support. Tighten both sides with screw and knob. (Note: this is the sealing height regulator).

Figure 27. Insert the vertical stand on the conveyor support..

Figure 28. Tighten both sides with screw and knob. You can make adjustments to the height of your band sealer.

8. Position the groove of the short drive shaft on the conveyor table unto the groove of the umbrella gear. Do not lock the umbrella gear to the conveyor table yet. Tighten the knobs under the conveyor to lock the conveyor in place.

Short drive shaft on conveyor table

Umbrella gear Figure 30. Tighten screw and knob on both sides under the conveyor to lock conveyor in place.

Figure 29. Insert the short drive shaft on the conveyor unto the groove of the umbrella gear.

9. Position the band sealer in the upright position. The height between the sealing bars and the conveyor table can be adjusted using the sealing height regulator. In some cases, the drive shaft may protrude from the back cover.
10. Move the conveyor belt until the grove of the short drive shaft on the conveyor table is locked in place with the groove of the umbrella gear. Be sure there is no space in between as it should fit exactly (moving the conveyor belt will turn the long shaft.) Set the three screws.

Figure 31. Umbrella gear and the conveyor should be flush against each other. Move the conveyor belt in order to align the groves.

Figure 32. Set the three screws back on the umbrella gear.

11. Replace the cover on the Umbrella Gear.

12. Final tuning:

a. To adjust height, use the sealing height regulator.

b. To adjust conveyor table, use knob under the conveyor table. (Figure 43, Item #14)

Maintenance

The following maintenance procedures should be followed to ensure the longevity of your CBS-880 band sealer.

Inspection and Cleaning

1. Inspect your machine daily.
2. Check if there is any foreign matter or dirt adhering to the band sealer.
3. To clean your band sealer, wipe down your sealer with silicone spray and a shop cloth. Do not apply silicone directly to your sealer. Definitely DO NOT wash down your machine with water.

Sealing and Drive Belts

1. Check and replace the belts as necessary. Both the sealing and drive belts are consumable items. Replace sealing belts when there are burn marks or if the belts become hard and brittle. Replace drive belts when the belts break or become badly cracked.
2. To change out the belts, make sure the machine is turned off.
3. Remove the safety cover (Figure 34, Item #6).
4. Remove the two drive belts.
5. To remove the sealing belts, push on the adjustment blocks (Figure 34, Item #3 & 20) and the sealing belts should easily slip off.
6. Put new sealing and/or drive belts back on the machine. Test the machine, making adjustments as necessary.
7. Replace the safety cover.
8. Check our YouTube channel (https://www.youtube.com/user/sealersales) for a video demo.

Turbocase Maintenance

1. Remove dust and clean motor at regular intervals. Avoid contact with alcohol, gasoline and benzene chemicals.

2. The turbocase should be oiled monthly with 50g 20# oil by:

a. Remove the back cover.

b. Locate the turbocase and unscrew the cap. Replenish any depleted gear oil with 50g 20# oil.

3. The motor brush (Part#BS-29A) is designed to be used 2,500 hours continuously. Replace carbon brush at regular intervals.

Figure 33. Turbocase cap.

Parts Diagram

To order spare parts, please use diagram and part #s below:

Figure 34 Spare Parts Diagram Overview

Figure 36 Heating / Cooling Blocks

Figure 40 Conveyor Table

Figure 42 Motor / Turbocase

Figure 43 Sealer Body

Figure 45 Umbrella Gear (only in CBS-880II units)

Figure 35. Spare Parts Diagram Overview

CBS-880-44

CBS-880-13A

CBS-880-13

CBS-880-84

CBS-880-8-5

CBS-880-7

BS-5B

BS-5C

BS-5A

CBS-880-6B

CBS-880-6A

CBS-880-6A

CBS-880-4

CBS-880-3

CBS-880-3A

CBS-880-6-26

CBS-880-40

CBS-880-42

CBS-880-42

CBS-880-6

CBS-880-6-27A

CBS-880-6-25

CBS-880-2-31

CBS-880-2

CBS-880-2-33

CBS-880-26

CBS-880-10

CBS-880-12

CBS-880-13

Figure 37. Heating / Cooling Blocks

BS-9I

CBS-880-9-2

BS-9J

CBS-880-21-19

BS-9D

BS-9F

CBS-880-9A

BS-9B

CBS-880-9A

CBS-880-9-10

CBS-880-9-11

CBS-880-21-23

CBS-880-21-24

CBS-880-8

CBS-880-21

CBS-880-21

CBS-880-8

Figure 39. Gears

Item

Quantity

Description

CBS-880-40

BS-35A

BS-35A

BS-35A

BS-33B

BS-35A

BS-35A

BS-35A

BS-35A

BS-35B

BS-35C

CBS-880-32

Comments

Figure 41. Conveyor Table

CBS-880-1

CBS-880-41

CBS-880-36

CBS-880-36

CBS-880-36

CBS-880-15

CBS-880-18

CBS-880-20

CBS-880-41

CBS-880-41

CBS-880-41-17

CBS-880-41-18

CBS-880-37

CBS-880-37

CBS-880-37

CBS-880-37

CBS-880-38

Cbs-88Oinstructionmanual

Figure 42. Motor / Turbocase

Item Comments Quantity Part # Description

110V DC motor

Not shown. In motor.

BS-29A motor brush CBS-880-30 worm-gearcaseassembly driving gearwheel pig iron gearwheel / turbocase support

Figure 44. Sealer Body

CBS-880-88-1

CBS-880-88-1

BS-25A

BS-22A

TMC-XMTE-1000-2

TMC-XMTE-1000-2-O

CBS-880-83

CBS-880-88

BS-52A

BS-45A

CBS-880-18

CBS-880-18

CBS-880-68

BS-67B

CBS-880-68B

CBS-880-88-18

R-JQX-13F

Figure 45. Umbrella Gear (only in CBS-880II units)

Item

Description

Quantity

CBS-880-72c

CBS-880-72c

CBS-880-72c

CBS-880-72c

CBS-880-72c

CBS-880-72c

CBS-880-72c

CBS-880-72c

CBS-880-72c

CBS-880-72c

CBS-880-72c

CBS-880-72c

Comments

Cbs-88Oinstructionmanual

Problem Possible Causes

Adjust two adjusting screws on the adjusting block

Driving wheel shaft is not parallel to Sealing belt is off tracking. driven wheel shaft seat (Part# CBS-880-13)

1. Adjust the vertical adjusting screw on driven

1. Too much tension on sealing belt

wheel seal to decrease tension on sealing belt

2. Sealing belt is off tracking 2. see above Sealing belts are tearing 3. Creases on the sealing belt
3. When installing belt, make sure no creases are
4. Residual film or other debris

found on belt

attached to the sealing belt

4. Clean surface of belt with cloth

1. Reduce temperature

2. Adjust guide belt

1. Temperature is too high 3. Clean or replace sealing belt

Seal is crumpled and film sticks to

2. Guide belt is not correctly in place sealing belts
3. Plastic melted on the sealing belt If any plastic melts on the sealing belt, your bags

will stick to the melted plastic

1. Embossing roller is worn out

1. Replace embossing roller

Embossing is not clear 2. Pressure spring on embossing

2. Adjust the embossing roller spring (Part# BS-5)

roller needs to be tightened

Adjust the clearance between blocks by adjusting

Clearance between heating blocks or Material will not pass through

the springs and stopping flakes found above the

sealing blocks cooling blocks may be too small blocks

Driving roller shaft is not parallel to Adjust using the conveyor belt adjustment (Part# Conveyor belt is off tracking the driven roller shaft BS-16)

1. Tighten the chain of driving roller shaft (front shaft) and middle shaft. (Parts # CBS-880-37 and

Conveyor and sealing belt are not Not enough tension on conveyor belt CBS-880-41) moving at same speed

2. Tighten the conveyor belt

1. Heat switch is damaged 1. Heat switch (BS-22-Large) t2. Heater (BS-9B) is damaged

Temperature doesn't rise or cannot

2. Heater (BS-9B)

be controlled 3. Temperature Controller

3. Temperature Controller
4. Coupling 4. Thermocouple (CBS-880-34)

Cbs-88Oinstructionmanual

Problem Possible Causes

Motor runs at a high speed and Speed controller has malfunctioned Replace the speed controller (BS-52A) cannot be regulated

1. No AC Voltage Check power source /power cord

Power,heater, and or fan switches

do not light up Connect the power 2. Open Fuse

3. Lamp is damaged Replace thefuse

Replace the lamp

Machine does not run 1. Board for speed regulation is 1. Replace the speed board (BS-52A) abnormal 2. Tighten the connecting screws

2. Doesn't connect well 3. Replace motor brushes (BS-29A)
3. Brushes in the motor are too short because of friction If the temperature controller works and the power lamp illuminates but the motor does not move, start off by checking the motor and turbocase connection. Remove the back of the machine and you will see bushing where the motor connects to the gear box. Ensure the bushing is not broken. Thereis also a set screw that connects thebushing to the gear box / motor shafts. Ensure that these are tight so that when the motor turns, the turbocase turns as well.

If the turbocase is noisy before it stopped working, the gear box could be broken inside. Lack of oil could cause this.

If the lamp illuminates and the motor does not turn, the motor speed controller may need to be

Other things could be faulty or wires to the motor or the brushes in the motor are worn.

Spare Parts List

Included with your band sealer are the following parts. Please note that spare parts included with your band sealer are subject to change without notice.

Power Cord (Part# PWC-CBS)

PTFE Sealing Belts (Part# CBS-880-10)

Drive Belts (Part# CBS-880-26)

Speed Adjusting PC Board (Part# BS-52A)

Optional: Typeset Box which includes numbers (0-9), Letters - EXD, embossing wheel, and key wrench

Quality Control Testing

Our band sealers are manufactured in a facility which is certified in accordance with ISO 9001:2008. In addition, we quality test all of our band sealers in our facility following a rigorous and exacting standards to ensure that the product you purchased is a high quality reliable machine.

Description Inspect all wiring on the unit, nothing is loosely attached. Make sure all wires are connected correctly. Make sure all connections are tight and properly mounted. (Ex: PC Board, Relay) Check parts to ensure they are in proper working order (ex: wheels, belts, knobs, etc) CBS-880 only - Attach the conveyor to the body via the drive shaft (Part #40). Detach after testing. Turn on machine - start, seal, fan, printer Check all knobs to make sure they start and end in the correct position Make adjustments as necessary if there is any unusual noise. Noise should be under 80db. Check fan - There should be air coming out of the cooling blocks Check motor - motor brushes should be held in tightly Check conveyor belt to make sure the belt is running smoothly and evenly Run machine for at least 20 minutes - after the seal temperature has been reached, seal bag sample to ensure good quality seal Clean machine Enter serial # of the unit in the manual Repackage sealer w/ QC form, sealed bag / printed sample and manual.

Date: Technician: