Compact Classic 32" Mat Cutter from Logan Graphics - 301-1 Manual, page 1

Page 1 of 7

Compact Classic 32" Mat Cutter from Logan Graphics - 301-1 Manual, page 2
Text on page 2

INSTRUCTION MANUAL

MODEL 301-1

COMPACT CLASSIC MAT CUTTER

INSTRUCTIONS AND OPERATION MANUAL

32in (81cm) mat cutting system with bevel

cutting head and straight cut mat knife.

For best results use only authentic Logan blades

Uses Logan Replacement Blade #270

CAUTION!!

MAT CUTTING BLADES ARE SHARP

Mat border calculator Mobile app

ID Number (on bottom of board)

Date (on bottom of board)

LoganGraphic.com

Page 2 of 7

Compact Classic 32" Mat Cutter from Logan Graphics - 301-1 Manual, page 3
Text on page 3

Congratulations on your purchase of the Logan Compact Classic Mat Cutter.

This versatile and dependable tool will prove to be a useful device for those seeking professional results from a low priced, easy to use mat cutter. This instruction manual is written to aquaint you thoroughly with this product. Please take some time to familiarize yourself with it before cutting. You will find that the time taken will be well worth it and you will be cutting quality mats in no time.

CHECK OF CONTENTS:

301-1 Compact Classic - 32” base board with Mat Guide, Bevel Cutting Head, Mat Knife, Slip Sheet, Instructional DVD and 1 five pack of Logan #270 blades.

IDENTIFICATION OF MACHINE COMPONENTS:

Cutting Board

Blade Holder Blade holding device which slides, allowing blade to cut into mat

Bevel Cutting Head

Slip Sheet A Slip Sheet is a piece of scrap mat board that is placed beneath the mat when bevel cutting

Start and Stop Indicator Line which shows where to begin and end cut

Guide Rail Used to guide cutting heads while in use

Cutting Board Vinyl covered base board of machine

Blade Knob Holds blade in place for cutting.

Mat Guide Used to set the border width of a mat and keep the mat in position

Nylon Guides Guides which allow Bevel Cutting Head to hook onto Guide Rail

Mat Knife

Blade Cover Covers blade on knife

Blade Knob Holds blade in place inside blade holder

Handle Knife handle which holds blade in two depth settings

Warranty

Logan Graphic Products, Inc. (“Logan”) warrants the 301-1 COMPACT CLASSIC to be free from defects in parts and workmanship for a period of two years from the date of original purchase. Logan warrants that it will either repair or replace, in its sole discretion, any necessary replacement parts found to be defective. Should the product need to be returned to Logan for repair or replacement parts, authorization for any return must come from Logan in writing. Costs of returning the product to Logan, including insurances, shall be borne by the purchaser. Logan shall not be liable for any damages or losses, incidental or consequential, direct or indirect, arising from the use of this product. This warranty extends only to the original purchaser and is not assignable or transferable. This warranty is in lieu of all other warranties, expressed or implied. Be advised that any Logan products purchased as “new” from an unauthorized dealer, such as an online auction site or similar, may be void of their warranty. Logan Graphic Products, Inc. 1100 Brown Street Wauconda, IL 60084 800/331-6232 847/526-5515

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com

Page 3 of 7

Compact Classic 32" Mat Cutter from Logan Graphics - 301-1 Manual, page 4
Text on page 4

Orientation

The procedures detailed in the following instructions refer to the right & left sides and top & bottom of the machine as shown (Fig. 1).

Blade Installation - Model 302 Bevel Cutter

Remove one blade from the package of five.

NOTE: Because the blades are packed with a small amount of oil, they may stick together. Be certain that only one blade is being inserted into the blade slot.

Place blade onto blade holder, sharp edge down and slide blade until corner of blade tip enters slot and hole in blade lines up with hole in blade holder (Fig. 2)(Fig. 3).

Safety Setting Standard Mat Board Setting Foamboard Setting

Replace blade knob and tighten.

NOTE: Blade holder has a spring that is designed to keep blade safely withdrawn when not in use. It is not designed to pull blade out of mat after cutting.

Blade Installation - Model 500 Mat Knife

Remove blade knob and blade cover.

Align blade hole over thread. Be sure sharp edge of blade is facing down.

Reassemble blade cover and blade knob.

NOTE: Adjust blade to foamboard (fully extended), standard mat board (middle setting) or safety (fully retracted) (Fig. 4).

Straight Cutting Board to Size

Remove mat guide and slip sheet.

Mark dimensions of cut on back of mat board.

Place mat color side down under guide rail, and align cut mark with edge of guiderail.

Set the proper depth setting on the #500 Mat Knife.

Hold the rail firmly with your left hand. With your right hand, hold the mat knife vertical so the handie is at a 45º angle (Fig. 5).

Draw the knife towards you along guide rail, keeping downward pressure on the mat knife.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com

Page 4 of 7

Compact Classic 32" Mat Cutter from Logan Graphics - 301-1 Manual, page 5
Text on page 5

Bevel Cutting Mat Openings

EXAMPLE: Cutting a mat with a 2” border.

To re-install the Mat Guide, loosen the Black Knobs with the raised edge towards the Guide Rail, line up the Mat Guide with the parallel slots. Hold the Mat Guide at either end and evenly drop the Mat Guide into the slots and then tighten the black knobs.

Set the Mat Guide to the desired border width. For example, for a 2” border, align the back of the Mat Guide at the 2” mark and tighten the Black Knobs (Fig. 6).

Make sure the Slip Sheet is in place before bevel cutting. You must use a Slip Sheet. The straight cut slot underneath the Guide Rail is for straight cutting only.

Place the mat color side down under the Guide Rail and up against the squaring bar and mat guide (Fig. 7).

Using a pencil, draw a line down the full length of the back of the matboard. Turn the mat after each marking and repeat this for the remaining three sides.

Attach the 302 Bevel Cutter to the Guide Rail by fitting the black nylon guides over the raised edge of the channel.

Position the cutter so the start & stop line lines up with the marked line closest to the bottom of the machine (Fig. 8).

Use your thumb to firmly depress the blade holder all the way down to insert the blade (Fig. 9).

With your left hand putting pressure down on the guide rail, slide the bevel cutter forward until the Start and Stop indicator lines up with the top pencil line. DO NOT GO PAST THE LINE! (Fig. 10)

NOTE: It is essential to keep even downward pressure on the Blade Holder as you cut.

  1. Use your thumb to pop the blade holder back out of the matboard, lift the guide rail slightly to turn the mat 1/4 turn and continue cutting the remaining three sides.

Adjustments

Bevel blade depth adjustment

Increase depth to increase overcuts - Decrease depth to reduce overcuts

Hold the 302 Bevel Cutter upside down in your hand with the blade activated in the cutting position.

Measure the exposed amount with a ruler at the same angle as the blade. For standard thickness mat board (4 ply/1.4mm) only 1/8” of blade should be seen (Fig. 11).

Turn blade depth screw (clockwise) to decrease blade depth and (counterclockwise) to increase depth.

NOTE: Always have blade depth set so that Slip Sheet is only slightly scored.

BEVEL

MAT CUTTER

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com

Page 5 of 7

Compact Classic 32" Mat Cutter from Logan Graphics - 301-1 Manual, page 6
Text on page 6

Re-parallel Mat Guide

Tools Needed: Phillips Screwdriver, Ruler

2” 5 cm

To re-parallel the Mat Guide, first determine that the Mat Guide is out of parallel by doing a parallel test.

Parallel Test:

Lock the Mat Guide at the 2” mark on the scale (Fig. 12).

Place a scrap piece of matboard under the Guide Rail and up against the Mat Guide at the far end of the machine.

Using a pencil, mark a line across the matboard.

Slide the mat all the way down near where you are standing keeping under the Guide Rail.

Mark another line across the matboard.

The piece of matboard should now appear to only have one single line across it. If the two lines drawn do not line up with each other, the Mat Guide needs to be re-paralleled.

Straight Edge

To Re-parallel:

Release the Mat Guide.

Use a Phillips head screwdriver to loosen the four screws on either side of the black knobs one turn.

Place a ruler or straight edge between the Mat Guide and the Guide Rail (Fig. 13).

Slide the Mat Guide against the straight edge and the Guide Rail. Make sure both the Mat Guide and the Guide Rail are making solid contact on both sides of the straight edge.

Re-tighten the Black Knobs first.

Then re-tighten the four screws. Do another parallel test to ensure that the Mat Guide is now parallel.

Mat Guide Assembly

If mat guide wedge becomes unscrewed from mat guide, reassemble making sure angle of wedge is aligned correctly (Fig. 14).

#112N Mat Guide Knob

#604 Mat Guide Screws (2)

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com

Page 6 of 7

Compact Classic 32" Mat Cutter from Logan Graphics - 301-1 Manual, page 7
Text on page 7

Trouble Shooting

Blade depth set too deep. Blade is dull. Blade is catching on previous cut in Slip Sheet. Uneven pressure being applied to Cutting Head during cut.

Overcut on Top Cut

Blade depth set too deep.

Overcut on Bottom Cut If too small - align start and stop indicator slightly below pencil line and cut.

If too big - align start and stop indicator slightly above pencil line and cut.

Mat Guide not parallel.

Cutting without a Slip Sheet.

Slip Sheet is worn out.

Not changing the blade often enough.

Machine not on a level surface.

Not using a Slip Sheet as least as long as the mat you are cutting.

Blade depth set too shallow.

Helpful Hints

Avoid Board Warp - Always store your Mat Cutter flat. Clean Guide Rail - Only use evaporative solvents such as lighter fluid or alcohol. Do not lubricate the Guide Rail: lubricants will soften the nylon guides and cause them to bind on guide rail. Cutting a Border Less Than 3/4” - Mark mat (back side) using a pencil and do not use Mat Guide. Blade Life - Use only authentic Logan blades to ensure best results. No two blades last the same amount of time. Size of mats and differences in mat board effect blade life. It is best practice to use a new blade whenever starting a new project.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com

Page 7 of 7 ยท End of manual

Quick start

  1. Install one Logan #270 blade in the 302 bevel cutter, sharp edge down, with the blade hole lined up with the holder hole, and tighten the blade knob. Blades are oiled and may stick together.
  2. To cut board to size, remove the mat guide and slip sheet, place the mat color side down under the guide rail with your mark at the rail edge, and draw the 500 mat knife toward you held vertical with the handle at 45°.
  3. For a mat opening, set the back of the Mat Guide to your border width (for example the 2" mark) and tighten the black knobs. Make sure the slip sheet is in place.
  4. Place the mat color side down against the squaring bar and mat guide and pencil a line along the full length. Turn and repeat for all four sides.
  5. Hook the bevel cutter on the rail, line up the start and stop line with the bottom pencil line, press the blade holder down, and push forward to the top line without going past it.
  6. Pop the blade holder out, turn the mat 1/4 turn and cut the remaining three sides.

Troubleshooting

ProblemLikely causeFix (from the manual)
Overcut on the top cutBlade depth set too deepReduce the bevel blade depth (turn the depth screw clockwise) so only 1/8" of blade shows for 4-ply mat board and the slip sheet is only slightly scored. Page 7
Overcut on the bottom cutStart and stop indicator not aligned with the pencil lineIf the overcut is too small, align the start and stop indicator slightly below the pencil line. If too big, align it slightly above the line. Page 7
Mat borders are uneven from one end to the otherMat Guide not parallel to the guide railRun the parallel test at the 2" mark and re-parallel the Mat Guide with a straight edge if the two pencil lines do not match. Page 7
Poor quality bevel cutsBlade too deep or dull, blade catching on a previous cut in the slip sheet, uneven pressure on the cutting head, no slip sheet or a worn one, or blade not changed often enoughUse a fresh Logan #270 blade, move or replace the slip sheet, set the correct blade depth, and keep even downward pressure on the blade holder throughout the cut. Page 7

Frequently asked questions

What replacement blade does the Logan 301-1 use?

It uses Logan replacement blade #270. A five-pack is included with the cutter (page 2, page 3).

How deep should the bevel blade be set?

For standard 4-ply (1.4 mm) mat board only 1/8" of blade should show when measured at the blade's angle. The slip sheet should be only slightly scored (page 5).

How do I cut a border narrower than 3/4"?

Mark the back of the mat with a pencil and cut without using the Mat Guide (page 7).

Can I lubricate the guide rail?

No. Lubricants soften the nylon guides and make them bind. Clean the rail only with evaporative solvents such as lighter fluid or alcohol (page 7).

What is the warranty on the Compact Classic?

Logan warrants the 301-1 against defects in parts and workmanship for two years from the original purchase date, for the original purchaser (page 3).