TABLEMATIC PLUS

INSTRUCTION

And

PARTS MANUAL

TABLEMATIC-PLUS IL LUSTRATION

TABLE/work base Platen Numbering Head Action Indicator Ink Cartridge Holder Cross Bar Head Block Bracket Head Leveling Bracket Knurled Knob 1/4" - 20 Head Lock Down Knob

10. ON/OFF Switch
11. Vertical adjust pressure
12. Horizontal adjust screw
13. Electrical Outlet For Numbering Head
14. Circuit Breaker
15. Built-in Side Guides
16. Magnetic Backstop
17. Foot Pedal
18. Control Panel

Place the TABLEMATIC Plus on a an uncluttered, sturdy desk, conveniently located near a 115V grounded outlet. Place the footswitch on the floor and plug the main power cord into the nearby outlet. DO NOT USE UNGROUNDED EQUIPMENT ON THE SAME CIRCUIT.

..-------- LIMITED WARRANTY--------.

Count Machinery Company warrants it's equipment against defective parts or workmanship under normal use and service for a period of: (1) year on all electrical and other parts; (90) days on numbering heads, During this time, COUNT will either repair or replace any COUNT unit returned (shipping prepaid) which, after examination by us, is determined to be defective. All freight charges for equipment sent in for warranty service is the responsibility of the purchaser and must be prepaid. Count will not be held responsible for any shipping charges. You may request your desired shipping method when the product is returned. If no me1hod is stated Count will send the time back UPS Ground. This warranty will be voided, if the product has been repaired or altered by anyone except for Count, or which has been subjected to misuse, negligence, or accident. Under no circumstances will Count be liable for consequential damages. The user shall determine the suitabiltty of the product for the intended use and the user 1 ,

assumes all risk and liability whatsoever in connection herewith. For service. return the unit prepaid with written \ I explanation of service needed to: COUNT MACHINERY COMPANY 2128 Vineyard Ave. Escondido, CA. 92029, 760-489-1400 Fax: 760-489-1543. J

Action Indicator/ Repeat Selector

Action Indicator Shaft& C Clip

Wheel Assembly

Action Indicator/ Repeat Selector - S-AAM-0870 WheelAssembly -H-1125 Ink Cartridge Swing Arm

• S-UNS-0912

Action Indicator Shaft & C-Clip - H-1176

Ink Cartridge Swing Arm

DEPRESSING A WHEEL

The standard Numbering Head is capable of recessing the first three wheels so there is no image when striking. For example, to print the number 4750 instead of 004750, you will need to depress the first two wheels. To do so. remove the Numbering Head from the Head Bracket and hold rt upside down resting ,t on a flat surface.

Swing the Ink Cartridge away from the wheels (or remove). Rotate the 1st wheel until the 9 is in the up position. Then press forward slightly and down. you will feel the wheel depress below the level of the others. Do the same to the 2nd wheel. Now you can print a 4 digit number. To return to position, simply rotate the wheel and 11 will pop up. This feature is also available on the custom Numbering Wheel with letters. Rotate the wheel until the blank position 1s up then press forward and down.

CHANGING DIRECTION OF THE HEAD

The Numbering Head is capable of rotating 270 degrees in 90 degree increments. To change the direction, simply remove the Vertical Bracket (using the 5/32 Wrench Supplted) and reinstall on the desired side. NOTE: To get to the Upper Mounting Screw for the Vertical Bracket, you must remove the Lock Knob and Pressure Adjustment Screw first. Take notice of how far the Adjustment Screw extends below the Stem so that when replacing you have a reference point. When replacing the Pressure Adjustment Screw, compress the sprrng slightly before trying to screw in the Adjustment Screw. This is a very fine thread and can easily be started incorrectly leading to thread damage. Do not try to press the Spring in with the AdJust Screw and turn at the same time. (Trust Us1 ) See photo.

FUNCTION OF HEAD BRACKETS

For direction purposes we will call the mounting of the Vertical Bracket. In this position:

PARALLEL

VERTICAL

It is important to be familiar with the adjustment of the brackets. Shown below are the various adjustments and the effect they have on the image of the number.

Depending on the orientation of the head the adjustment of the Vertical Bracket can be either:

In the Parallel Position: LEFT TO RIGHT

In the Vertical Position: TOP TO BOTTOM

oo::z.

• ADJUSTING THE VERTICAL BRACKET

The bottom of the vertical bracket is slotted to allow for movement. The effect of this movement depends on the orientation of the head (See Function of Head Brackets). To make an adjustment to the vertical bracket, simply loosen the lower screw and slide toward the direction desired, then retighten the screw. It is not necessary to loosen the top screw.