Page 1 of 10
Page 2 of 10
Text on page 3
TABLE OF CONTENTS
CONTENTS
PAGE
READ CAREFULLY BEFORE USING
Proper care of your new hard drive punch will ensure many years of trouble free operation, with minimum of maintenance or repair.
IMPORTANT:
Please note that all packaging should be retained by the customer for (30) days from the time of receipt. In the event that this unit needs to be sent back for replacement or repair this packaging will be required to do so. Should the packaging have been discarded before the (30) day requested period, packaging costs may be incurred by the customer.
SPECIFICATIONS
HARD DRIVE PUNCH
Security Level:
Dimensions: 19.75” X 20” X 34.5”
Power Supply:
115v 50/60 Hz 15 Amp
Warranty includes labor but excludes wearable parts.
Page 3 of 10
Text on page 4
IMPORTANT SAFETY PRECAUTIONS
Your new shredder features powerful cutting mechanisms that may cause serious injury. Please follow all safety precautions.
- Only store, transport, and operate the shredder in an upright position!
- All liquids and gases used on the shredder must comply with Dahle guidelines!
- The shredder must only be operated in enclosed spaces at temperatures of 15 °C to
32 °C(59 °F–90 °F) and non-condensed humidity of 15% to 95%!
- Do not place the shredder near a heat source!
- Ensure the shredder is firmly on the floor at a distance of 4” from the wall; activate
- Avoid any accumulation of heat!
- The mains socket must be grounded and easily accessible at all times!
- Use only the power cord supplied with the device by Dahle and ensure that it is not
- Ensure that the building installation has short-circuit protection: max. 16 A (US
- Do not use near flammable liquids and gases!
- Do not use near caustic substances!
- Do not subject to moisture!
- Do not open up the machine!
- Automatic start-up!
- Switch off the shredder at the main switch when not in use!
- Only use the shredder provided that it is in perfect working order, while observing
the operating instructions and the usual regulations, guidelines and applicable safety and accident prevention requirements. Take the shredder out of service immediately if faults occur!
- The device is not intended for use by persons (including children) with restricted
physical, sensory or mental capabilities or a lack of experience and knowledge, unless they are working under supervision or receive detailed instruction about how to use the device from a person who is responsible for safety.
Page 4 of 10
Text on page 5
IMPORTANT SAFETY PRECAUTIONS
It is obligatory to follow the safety instructions!
Read the operating instructions carefully before using the shredder!
This shredder is not intended to be used by children (the product is not a toy)!
Do not touch the feed opening with your hands!
Do not allow items of clothing to touch the feed opening!
Do not allow your hair to touch the feed opening!
Prior to maintenance work, disconnect the shredder from the power supply!
INSTALLATION
- Insert supplied waste bin into the machine.
- Plug machine directly into a wall outlet.
Do not use a power strip or extension cord.
Page 5 of 10
Text on page 6
OPERATION
- Turn on both power switches. One is located inside the door and the other is on
the right side of the shredder.Slide open the clear safety shield feed opening door located at the top of the machine.
- Insert 2.5” or 3.5” Hard Drive into the feed opening.
- Slide the safety shield feed opening door closed.
- Press the START button on the keypad. The punching area will illuminate and the punching die will drive through the hard drive. After a short delay, the die will reverse direction automatically and the LED light will go out, indicating the process is complete.
- Press down the Discharge Handle located on the top of the machine to release the punched hard drive into the waste container.
REVERSE
- In case of a jam, the machine is designed to automatically operate in reverse.
DOOR OPEN
- The DOOR OPEN will illuminate if the safety shield feed opening door located on the top of the machine or the cabinet door is open. Both must be closed for the machine to operate.
FULL
- The FULL LED light will illuminate if the waste container is full. Open the cabinet door, empty the waste container, replace the waste container, and close the cabinet door.
Page 6 of 10
Text on page 7
MAINTENANCE
- Switch off the machine and disconnect power by removing
power cord from wall outlet.
- Clean the exterior of the machine with a soft cloth. Do not use
harsh detergents or chemicals.
WARRANTY
Dahle guarantees this hard drive punch to be free from manufacturing defects (materials / workmanship) for a period of one year.
This warranty shall not apply to wearable items or defects caused by ordinary wear and tear, insufficient maintenance or improper operation. This warranty applies to the original purchaser only and is not transferable. There are no other warranties expressed or implied beyond the face of this agreement.
Page 7 of 10
Page 8 of 10
Page 9 of 10
Text on page 10
Dahle North America, Inc. 49 Vose Farm Road Peterborough, NH 03458 Tel. (800) 995-1379 info@dahle.com
www.dahle.com
Page 10 of 10 ยท End of manual
Quick start
- Insert the supplied waste bin and plug the machine directly into a wall outlet (no power strip or extension cord).
- Turn on both power switches: one inside the door and one on the right side.
- Slide open the clear safety shield feed door on top of the machine.
- Insert a 2.5" or 3.5" hard drive and slide the door closed.
- Press START. The die punches through the drive and reverses automatically; the light goes out when done.
- Press down the Discharge Handle on top to drop the punched drive into the waste container.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Jam during punching | The machine is designed to reverse automatically when a jam occurs. Page 6 | |
| DOOR OPEN light is lit and the machine won't run | The safety shield feed door on top or the cabinet door is open. | Close both doors. Page 6 |
| FULL light is lit | The waste container is full. | Open the cabinet door, empty and replace the waste container, and close the door. Page 6 |
Frequently asked questions
What size hard drives does the PowerTEC 818 HD accept?
2.5" and 3.5" hard drives (page 6).
How do I remove a punched drive?
Press down the Discharge Handle on top of the machine to release it into the waste container (page 6).
What power does it need?
115v 50/60 Hz, 15 Amp. Plug it directly into a wall outlet (page 3, page 5).
What is the warranty?
One year against manufacturing defects for the original purchaser; wearable items are excluded (page 7).
